From fe2921d137ce66eb1176c8fb0cdf692d697bda9b Mon Sep 17 00:00:00 2001 From: Laurent Ghigonis Date: Mon, 25 Mar 2013 18:55:15 +0100 Subject: add viensamoi - WIFI tools targeting clients --- viensamoi/hostapd.conf | 1128 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1128 insertions(+) create mode 100644 viensamoi/hostapd.conf (limited to 'viensamoi/hostapd.conf') diff --git a/viensamoi/hostapd.conf b/viensamoi/hostapd.conf new file mode 100644 index 0000000..9e28b45 --- /dev/null +++ b/viensamoi/hostapd.conf @@ -0,0 +1,1128 @@ +##### hostapd configuration file ############################################## +# Empty lines and lines starting with # are ignored + +# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for +# management frames); ath0 for madwifi +interface=wlan0 + +# In case of madwifi, atheros, and nl80211 driver interfaces, an additional +# configuration parameter, bridge, may be used to notify hostapd if the +# interface is included in a bridge. This parameter is not used with Host AP +# driver. If the bridge parameter is not set, the drivers will automatically +# figure out the bridge interface (assuming sysfs is enabled and mounted to +# /sys) and this parameter may not be needed. +# +# For nl80211, this parameter can be used to request the AP interface to be +# added to the bridge automatically (brctl may refuse to do this before hostapd +# has been started to change the interface mode). If needed, the bridge +# interface is also created. +#bridge=br0 + +# Driver interface type (hostap/wired/madwifi/test/none/nl80211/bsd); +# default: hostap). nl80211 is used with all Linux mac80211 drivers. +# Use driver=none if building hostapd as a standalone RADIUS server that does +# not control any wireless/wired driver. +# driver=hostap +driver=nl80211 + +# hostapd event logger configuration +# +# Two output method: syslog and stdout (only usable if not forking to +# background). +# +# Module bitfield (ORed bitfield of modules that will be logged; -1 = all +# modules): +# bit 0 (1) = IEEE 802.11 +# bit 1 (2) = IEEE 802.1X +# bit 2 (4) = RADIUS +# bit 3 (8) = WPA +# bit 4 (16) = driver interface +# bit 5 (32) = IAPP +# bit 6 (64) = MLME +# +# Levels (minimum value for logged events): +# 0 = verbose debugging +# 1 = debugging +# 2 = informational messages +# 3 = notification +# 4 = warning +# +logger_syslog=-1 +logger_syslog_level=0 +logger_stdout=-1 +logger_stdout_level=0 + +# Dump file for state information (on SIGUSR1) +dump_file=/tmp/hostapd.dump + +# Interface for separate control program. If this is specified, hostapd +# will create this directory and a UNIX domain socket for listening to requests +# from external programs (CLI/GUI, etc.) for status information and +# configuration. The socket file will be named based on the interface name, so +# multiple hostapd processes/interfaces can be run at the same time if more +# than one interface is used. +# /var/run/hostapd is the recommended directory for sockets and by default, +# hostapd_cli will use it when trying to connect with hostapd. +ctrl_interface=wlan0 + +# Access control for the control interface can be configured by setting the +# directory to allow only members of a group to use sockets. This way, it is +# possible to run hostapd as root (since it needs to change network +# configuration and open raw sockets) and still allow GUI/CLI components to be +# run as non-root users. However, since the control interface can be used to +# change the network configuration, this access needs to be protected in many +# cases. By default, hostapd is configured to use gid 0 (root). If you +# want to allow non-root users to use the contron interface, add a new group +# and change this value to match with that group. Add users that should have +# control interface access to this group. +# +# This variable can be a group name or gid. +#ctrl_interface_group=wheel +ctrl_interface_group=0 + + +##### IEEE 802.11 related configuration ####################################### + +# SSID to be used in IEEE 802.11 management frames +ssid=BigJambox + +# Country code (ISO/IEC 3166-1). Used to set regulatory domain. +# Set as needed to indicate country in which device is operating. +# This can limit available channels and transmit power. +#country_code=US + +# Enable IEEE 802.11d. This advertises the country_code and the set of allowed +# channels and transmit power levels based on the regulatory limits. The +# country_code setting must be configured with the correct country for +# IEEE 802.11d functions. +# (default: 0 = disabled) +#ieee80211d=1 + +# Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g, +# Default: IEEE 802.11b +hw_mode=g + +# Channel number (IEEE 802.11) +# (default: 0, i.e., not set) +# Please note that some drivers do not use this value from hostapd and the +# channel will need to be configured separately with iwconfig. +channel=1 + +# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) +beacon_int=100 + +# DTIM (delivery traffic information message) period (range 1..255): +# number of beacons between DTIMs (1 = every beacon includes DTIM element) +# (default: 2) +dtim_period=2 + +# Maximum number of stations allowed in station table. New stations will be +# rejected after the station table is full. IEEE 802.11 has a limit of 2007 +# different association IDs, so this number should not be larger than that. +# (default: 2007) +max_num_sta=255 + +# RTS/CTS threshold; 2347 = disabled (default); range 0..2347 +# If this field is not included in hostapd.conf, hostapd will not control +# RTS threshold and 'iwconfig wlan# rts ' can be used to set it. +rts_threshold=2347 + +# Fragmentation threshold; 2346 = disabled (default); range 256..2346 +# If this field is not included in hostapd.conf, hostapd will not control +# fragmentation threshold and 'iwconfig wlan# frag ' can be used to set +# it. +fragm_threshold=2346 + +# Rate configuration +# Default is to enable all rates supported by the hardware. This configuration +# item allows this list be filtered so that only the listed rates will be left +# in the list. If the list is empty, all rates are used. This list can have +# entries that are not in the list of rates the hardware supports (such entries +# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110. +# If this item is present, at least one rate have to be matching with the rates +# hardware supports. +# default: use the most common supported rate setting for the selected +# hw_mode (i.e., this line can be removed from configuration file in most +# cases) +#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540 + +# Basic rate set configuration +# List of rates (in 100 kbps) that are included in the basic rate set. +# If this item is not included, usually reasonable default set is used. +#basic_rates=10 20 +#basic_rates=10 20 55 110 +#basic_rates=60 120 240 + +# Short Preamble +# This parameter can be used to enable optional use of short preamble for +# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance. +# This applies only to IEEE 802.11b-compatible networks and this should only be +# enabled if the local hardware supports use of short preamble. If any of the +# associated STAs do not support short preamble, use of short preamble will be +# disabled (and enabled when such STAs disassociate) dynamically. +# 0 = do not allow use of short preamble (default) +# 1 = allow use of short preamble +#preamble=1 + +# Station MAC address -based authentication +# Please note that this kind of access control requires a driver that uses +# hostapd to take care of management frame processing and as such, this can be +# used with driver=hostap or driver=nl80211, but not with driver=madwifi. +# 0 = accept unless in deny list +# 1 = deny unless in accept list +# 2 = use external RADIUS server (accept/deny lists are searched first) +macaddr_acl=0 + +# Accept/deny lists are read from separate files (containing list of +# MAC addresses, one per line). Use absolute path name to make sure that the +# files can be read on SIGHUP configuration reloads. +#accept_mac_file=/etc/hostapd/hostapd.accept +#deny_mac_file=/etc/hostapd/hostapd.deny + +# IEEE 802.11 specifies two authentication algorithms. hostapd can be +# configured to allow both of these or only one. Open system authentication +# should be used with IEEE 802.1X. +# Bit fields of allowed authentication algorithms: +# bit 0 = Open System Authentication +# bit 1 = Shared Key Authentication (requires WEP) +auth_algs=3 + +# Send empty SSID in beacons and ignore probe request frames that do not +# specify full SSID, i.e., require stations to know SSID. +# default: disabled (0) +# 1 = send empty (length=0) SSID in beacon and ignore probe request for +# broadcast SSID +# 2 = clear SSID (ASCII 0), but keep the original length (this may be required +# with some clients that do not support empty SSID) and ignore probe +# requests for broadcast SSID +ignore_broadcast_ssid=0 + +# TX queue parameters (EDCF / bursting) +# tx_queue__ +# queues: data0, data1, data2, data3, after_beacon, beacon +# (data0 is the highest priority queue) +# parameters: +# aifs: AIFS (default 2) +# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023) +# cwmax: cwMax (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023); cwMax >= cwMin +# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for +# bursting +# +# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): +# These parameters are used by the access point when transmitting frames +# to the clients. +# +# Low priority / AC_BK = background +#tx_queue_data3_aifs=7 +#tx_queue_data3_cwmin=15 +#tx_queue_data3_cwmax=1023 +#tx_queue_data3_burst=0 +# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 +# +# Normal priority / AC_BE = best effort +#tx_queue_data2_aifs=3 +#tx_queue_data2_cwmin=15 +#tx_queue_data2_cwmax=63 +#tx_queue_data2_burst=0 +# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 +# +# High priority / AC_VI = video +#tx_queue_data1_aifs=1 +#tx_queue_data1_cwmin=7 +#tx_queue_data1_cwmax=15 +#tx_queue_data1_burst=3.0 +# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 +# +# Highest priority / AC_VO = voice +#tx_queue_data0_aifs=1 +#tx_queue_data0_cwmin=3 +#tx_queue_data0_cwmax=7 +#tx_queue_data0_burst=1.5 +# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3 + +# 802.1D Tag (= UP) to AC mappings +# WMM specifies following mapping of data frames to different ACs. This mapping +# can be configured using Linux QoS/tc and sch_pktpri.o module. +# 802.1D Tag 802.1D Designation Access Category WMM Designation +# 1 BK AC_BK Background +# 2 - AC_BK Background +# 0 BE AC_BE Best Effort +# 3 EE AC_BE Best Effort +# 4 CL AC_VI Video +# 5 VI AC_VI Video +# 6 VO AC_VO Voice +# 7 NC AC_VO Voice +# Data frames with no priority information: AC_BE +# Management frames: AC_VO +# PS-Poll frames: AC_BE + +# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): +# for 802.11a or 802.11g networks +# These parameters are sent to WMM clients when they associate. +# The parameters will be used by WMM clients for frames transmitted to the +# access point. +# +# note - txop_limit is in units of 32microseconds +# note - acm is admission control mandatory flag. 0 = admission control not +# required, 1 = mandatory +# note - here cwMin and cmMax are in exponent form. the actual cw value used +# will be (2^n)-1 where n is the value given here +# +wmm_enabled=1 +# +# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] +# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) +#uapsd_advertisement_enabled=1 +# +# Low priority / AC_BK = background +wmm_ac_bk_cwmin=4 +wmm_ac_bk_cwmax=10 +wmm_ac_bk_aifs=7 +wmm_ac_bk_txop_limit=0 +wmm_ac_bk_acm=0 +# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 +# +# Normal priority / AC_BE = best effort +wmm_ac_be_aifs=3 +wmm_ac_be_cwmin=4 +wmm_ac_be_cwmax=10 +wmm_ac_be_txop_limit=0 +wmm_ac_be_acm=0 +# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 +# +# High priority / AC_VI = video +wmm_ac_vi_aifs=2 +wmm_ac_vi_cwmin=3 +wmm_ac_vi_cwmax=4 +wmm_ac_vi_txop_limit=94 +wmm_ac_vi_acm=0 +# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 +# +# Highest priority / AC_VO = voice +wmm_ac_vo_aifs=2 +wmm_ac_vo_cwmin=2 +wmm_ac_vo_cwmax=3 +wmm_ac_vo_txop_limit=47 +wmm_ac_vo_acm=0 +# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102 + +# Static WEP key configuration +# +# The key number to use when transmitting. +# It must be between 0 and 3, and the corresponding key must be set. +# default: not set +#wep_default_key=0 +# The WEP keys to use. +# A key may be a quoted string or unquoted hexadecimal digits. +# The key length should be 5, 13, or 16 characters, or 10, 26, or 32 +# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or +# 128-bit (152-bit) WEP is used. +# Only the default key must be supplied; the others are optional. +# default: not set +#wep_key0=123456789a +#wep_key1="vwxyz" +#wep_key2=0102030405060708090a0b0c0d +#wep_key3=".2.4.6.8.0.23" + +# Station inactivity limit +# +# If a station does not send anything in ap_max_inactivity seconds, an +# empty data frame is sent to it in order to verify whether it is +# still in range. If this frame is not ACKed, the station will be +# disassociated and then deauthenticated. This feature is used to +# clear station table of old entries when the STAs move out of the +# range. +# +# The station can associate again with the AP if it is still in range; +# this inactivity poll is just used as a nicer way of verifying +# inactivity; i.e., client will not report broken connection because +# disassociation frame is not sent immediately without first polling +# the STA with a data frame. +# default: 300 (i.e., 5 minutes) +#ap_max_inactivity=300 + +# Disassociate stations based on excessive transmission failures or other +# indications of connection loss. This depends on the driver capabilities and +# may not be available with all drivers. +#disassoc_low_ack=1 + +# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to +# remain asleep). Default: 65535 (no limit apart from field size) +#max_listen_interval=100 + +# WDS (4-address frame) mode with per-station virtual interfaces +# (only supported with driver=nl80211) +# This mode allows associated stations to use 4-address frames to allow layer 2 +# bridging to be used. +#wds_sta=1 + +# If bridge parameter is set, the WDS STA interface will be added to the same +# bridge by default. This can be overridden with the wds_bridge parameter to +# use a separate bridge. +#wds_bridge=wds-br0 + +# Client isolation can be used to prevent low-level bridging of frames between +# associated stations in the BSS. By default, this bridging is allowed. +#ap_isolate=1 + +##### IEEE 802.11n related configuration ###################################### + +# ieee80211n: Whether IEEE 802.11n (HT) is enabled +# 0 = disabled (default) +# 1 = enabled +# Note: You will also need to enable WMM for full HT functionality. +#ieee80211n=1 + +# ht_capab: HT capabilities (list of flags) +# LDPC coding capability: [LDPC] = supported +# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary +# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz +# with secondary channel below the primary channel +# (20 MHz only if neither is set) +# Note: There are limits on which channels can be used with HT40- and +# HT40+. Following table shows the channels that may be available for +# HT40- and HT40+ use per IEEE 802.11n Annex J: +# freq HT40- HT40+ +# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) +# 5 GHz 40,48,56,64 36,44,52,60 +# (depending on the location, not all of these channels may be available +# for use) +# Please note that 40 MHz channels may switch their primary and secondary +# channels if needed or creation of 40 MHz channel maybe rejected based +# on overlapping BSSes. These changes are done automatically when hostapd +# is setting up the 40 MHz channel. +# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC] +# (SMPS disabled if neither is set) +# HT-greenfield: [GF] (disabled if not set) +# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) +# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) +# Tx STBC: [TX-STBC] (disabled if not set) +# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial +# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC +# disabled if none of these set +# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) +# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not +# set) +# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) +# PSMP support: [PSMP] (disabled if not set) +# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) +#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40] + +# Require stations to support HT PHY (reject association if they do not) +#require_ht=1 + +##### IEEE 802.1X-2004 related configuration ################################## + +# Require IEEE 802.1X authorization +#ieee8021x=1 + +# IEEE 802.1X/EAPOL version +# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL +# version 2. However, there are many client implementations that do not handle +# the new version number correctly (they seem to drop the frames completely). +# In order to make hostapd interoperate with these clients, the version number +# can be set to the older version (1) with this configuration value. +#eapol_version=2 + +# Optional displayable message sent with EAP Request-Identity. The first \0 +# in this string will be converted to ASCII-0 (nul). This can be used to +# separate network info (comma separated list of attribute=value pairs); see, +# e.g., RFC 4284. +#eap_message=hello +#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com + +# WEP rekeying (disabled if key lengths are not set or are set to 0) +# Key lengths for default/broadcast and individual/unicast keys: +# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits) +# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits) +#wep_key_len_broadcast=5 +#wep_key_len_unicast=5 +# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once) +#wep_rekey_period=300 + +# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if +# only broadcast keys are used) +eapol_key_index_workaround=0 + +# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable +# reauthentication). +#eap_reauth_period=3600 + +# Use PAE group address (01:80:c2:00:00:03) instead of individual target +# address when sending EAPOL frames with driver=wired. This is the most common +# mechanism used in wired authentication, but it also requires that the port +# is only used by one station. +#use_pae_group_addr=1 + +##### Integrated EAP server ################################################### + +# Optionally, hostapd can be configured to use an integrated EAP server +# to process EAP authentication locally without need for an external RADIUS +# server. This functionality can be used both as a local authentication server +# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices. + +# Use integrated EAP server instead of external RADIUS authentication +# server. This is also needed if hostapd is configured to act as a RADIUS +# authentication server. +eap_server=0 + +# Path for EAP server user database +#eap_user_file=/etc/hostapd/hostapd.eap_user + +# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS +#ca_cert=/etc/hostapd/hostapd.ca.pem + +# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS +#server_cert=/etc/hostapd/hostapd.server.pem + +# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS +# This may point to the same file as server_cert if both certificate and key +# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be +# used by commenting out server_cert and specifying the PFX file as the +# private_key. +#private_key=/etc/hostapd/hostapd.server.prv + +# Passphrase for private key +#private_key_passwd=secret passphrase + +# Enable CRL verification. +# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a +# valid CRL signed by the CA is required to be included in the ca_cert file. +# This can be done by using PEM format for CA certificate and CRL and +# concatenating these into one file. Whenever CRL changes, hostapd needs to be +# restarted to take the new CRL into use. +# 0 = do not verify CRLs (default) +# 1 = check the CRL of the user certificate +# 2 = check all CRLs in the certificate path +#check_crl=1 + +# dh_file: File path to DH/DSA parameters file (in PEM format) +# This is an optional configuration file for setting parameters for an +# ephemeral DH key exchange. In most cases, the default RSA authentication does +# not use this configuration. However, it is possible setup RSA to use +# ephemeral DH key exchange. In addition, ciphers with DSA keys always use +# ephemeral DH keys. This can be used to achieve forward secrecy. If the file +# is in DSA parameters format, it will be automatically converted into DH +# params. This parameter is required if anonymous EAP-FAST is used. +# You can generate DH parameters file with OpenSSL, e.g., +# "openssl dhparam -out /etc/hostapd/hostapd.dh.pem 1024" +#dh_file=/etc/hostapd/hostapd.dh.pem + +# Fragment size for EAP methods +#fragment_size=1400 + +# Configuration data for EAP-SIM database/authentication gateway interface. +# This is a text string in implementation specific format. The example +# implementation in eap_sim_db.c uses this as the UNIX domain socket name for +# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:" +# prefix. +#eap_sim_db=unix:/tmp/hlr_auc_gw.sock + +# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret, +# random value. It is configured as a 16-octet value in hex format. It can be +# generated, e.g., with the following command: +# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' ' +#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f + +# EAP-FAST authority identity (A-ID) +# A-ID indicates the identity of the authority that issues PACs. The A-ID +# should be unique across all issuing servers. In theory, this is a variable +# length field, but due to some existing implementations requiring A-ID to be +# 16 octets in length, it is strongly recommended to use that length for the +# field to provid interoperability with deployed peer implementations. This +# field is configured in hex format. +#eap_fast_a_id=101112131415161718191a1b1c1d1e1f + +# EAP-FAST authority identifier information (A-ID-Info) +# This is a user-friendly name for the A-ID. For example, the enterprise name +# and server name in a human-readable format. This field is encoded as UTF-8. +#eap_fast_a_id_info=test server + +# Enable/disable different EAP-FAST provisioning modes: +#0 = provisioning disabled +#1 = only anonymous provisioning allowed +#2 = only authenticated provisioning allowed +#3 = both provisioning modes allowed (default) +#eap_fast_prov=3 + +# EAP-FAST PAC-Key lifetime in seconds (hard limit) +#pac_key_lifetime=604800 + +# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard +# limit). The server will generate a new PAC-Key when this number of seconds +# (or fewer) of the lifetime remains. +#pac_key_refresh_time=86400 + +# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND +# (default: 0 = disabled). +#eap_sim_aka_result_ind=1 + +# Trusted Network Connect (TNC) +# If enabled, TNC validation will be required before the peer is allowed to +# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other +# EAP method is enabled, the peer will be allowed to connect without TNC. +#tnc=1 + + +##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) ####################### + +# Interface to be used for IAPP broadcast packets +#iapp_interface=wlan0 + + +##### RADIUS client configuration ############################################# +# for IEEE 802.1X with external Authentication Server, IEEE 802.11 +# authentication with external ACL for MAC addresses, and accounting + +# The own IP address of the access point (used as NAS-IP-Address) +own_ip_addr=127.0.0.1 + +# Optional NAS-Identifier string for RADIUS messages. When used, this should be +# a unique to the NAS within the scope of the RADIUS server. For example, a +# fully qualified domain name can be used here. +# When using IEEE 802.11r, nas_identifier must be set and must be between 1 and +# 48 octets long. +#nas_identifier=ap.example.com + +# RADIUS authentication server +#auth_server_addr=127.0.0.1 +#auth_server_port=1812 +#auth_server_shared_secret=secret + +# RADIUS accounting server +#acct_server_addr=127.0.0.1 +#acct_server_port=1813 +#acct_server_shared_secret=secret + +# Secondary RADIUS servers; to be used if primary one does not reply to +# RADIUS packets. These are optional and there can be more than one secondary +# server listed. +#auth_server_addr=127.0.0.2 +#auth_server_port=1812 +#auth_server_shared_secret=secret2 +# +#acct_server_addr=127.0.0.2 +#acct_server_port=1813 +#acct_server_shared_secret=secret2 + +# Retry interval for trying to return to the primary RADIUS server (in +# seconds). RADIUS client code will automatically try to use the next server +# when the current server is not replying to requests. If this interval is set, +# primary server will be retried after configured amount of time even if the +# currently used secondary server is still working. +#radius_retry_primary_interval=600 + + +# Interim accounting update interval +# If this is set (larger than 0) and acct_server is configured, hostapd will +# send interim accounting updates every N seconds. Note: if set, this overrides +# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this +# value should not be configured in hostapd.conf, if RADIUS server is used to +# control the interim interval. +# This value should not be less 600 (10 minutes) and must not be less than +# 60 (1 minute). +#radius_acct_interim_interval=600 + +# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN +# is used for the stations. This information is parsed from following RADIUS +# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN), +# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value +# VLANID as a string). vlan_file option below must be configured if dynamic +# VLANs are used. Optionally, the local MAC ACL list (accept_mac_file) can be +# used to set static client MAC address to VLAN ID mapping. +# 0 = disabled (default) +# 1 = option; use default interface if RADIUS server does not include VLAN ID +# 2 = required; reject authentication if RADIUS server does not include VLAN ID +#dynamic_vlan=0 + +# VLAN interface list for dynamic VLAN mode is read from a separate text file. +# This list is used to map VLAN ID from the RADIUS server to a network +# interface. Each station is bound to one interface in the same way as with +# multiple BSSIDs or SSIDs. Each line in this text file is defining a new +# interface and the line must include VLAN ID and interface name separated by +# white space (space or tab). +#vlan_file=/etc/hostapd/hostapd.vlan + +# Interface where 802.1q tagged packets should appear when a RADIUS server is +# used to determine which VLAN a station is on. hostapd creates a bridge for +# each VLAN. Then hostapd adds a VLAN interface (associated with the interface +# indicated by 'vlan_tagged_interface') and the appropriate wireless interface +# to the bridge. +#vlan_tagged_interface=wlan0 + + +##### RADIUS authentication server configuration ############################## + +# hostapd can be used as a RADIUS authentication server for other hosts. This +# requires that the integrated EAP server is also enabled and both +# authentication services are sharing the same configuration. + +# File name of the RADIUS clients configuration for the RADIUS server. If this +# commented out, RADIUS server is disabled. +#radius_server_clients=/etc/hostapd/hostapd.radius_clients + +# The UDP port number for the RADIUS authentication server +#radius_server_auth_port=1812 + +# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API) +#radius_server_ipv6=1 + + +##### WPA/IEEE 802.11i configuration ########################################## + +# Enable WPA. Setting this variable configures the AP to require WPA (either +# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either +# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. +# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), +# RADIUS authentication server must be configured, and WPA-EAP must be included +# in wpa_key_mgmt. +# This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) +# and/or WPA2 (full IEEE 802.11i/RSN): +# bit0 = WPA +# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) +#wpa=1 + +# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit +# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase +# (8..63 characters) that will be converted to PSK. This conversion uses SSID +# so the PSK changes when ASCII passphrase is used and the SSID is changed. +# wpa_psk (dot11RSNAConfigPSKValue) +# wpa_passphrase (dot11RSNAConfigPSKPassPhrase) +#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef +#wpa_passphrase=secret passphrase + +# Optionally, WPA PSKs can be read from a separate text file (containing list +# of (PSK,MAC address) pairs. This allows more than one PSK to be configured. +# Use absolute path name to make sure that the files can be read on SIGHUP +# configuration reloads. +#wpa_psk_file=/etc/hostapd/hostapd.wpa_psk + +# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The +# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be +# added to enable SHA256-based stronger algorithms. +# (dot11RSNAConfigAuthenticationSuitesTable) +#wpa_key_mgmt=WPA-PSK WPA-EAP + +# Set of accepted cipher suites (encryption algorithms) for pairwise keys +# (unicast packets). This is a space separated list of algorithms: +# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] +# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] +# Group cipher suite (encryption algorithm for broadcast and multicast frames) +# is automatically selected based on this configuration. If only CCMP is +# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise, +# TKIP will be used as the group cipher. +# (dot11RSNAConfigPairwiseCiphersTable) +# Pairwise cipher for WPA (v1) (default: TKIP) +#wpa_pairwise=TKIP CCMP +# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) +#rsn_pairwise=CCMP + +# Time interval for rekeying GTK (broadcast/multicast encryption keys) in +# seconds. (dot11RSNAConfigGroupRekeyTime) +#wpa_group_rekey=600 + +# Rekey GTK when any STA that possesses the current GTK is leaving the BSS. +# (dot11RSNAConfigGroupRekeyStrict) +#wpa_strict_rekey=1 + +# Time interval for rekeying GMK (master key used internally to generate GTKs +# (in seconds). +#wpa_gmk_rekey=86400 + +# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of +# PTK to mitigate some attacks against TKIP deficiencies. +#wpa_ptk_rekey=600 + +# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up +# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN +# authentication and key handshake before actually associating with a new AP. +# (dot11RSNAPreauthenticationEnabled) +#rsn_preauth=1 +# +# Space separated list of interfaces from which pre-authentication frames are +# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all +# interface that are used for connections to other APs. This could include +# wired interfaces and WDS links. The normal wireless data interface towards +# associated stations (e.g., wlan0) should not be added, since +# pre-authentication is only used with APs other than the currently associated +# one. +#rsn_preauth_interfaces=eth0 + +# peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e) is +# allowed. This is only used with RSN/WPA2. +# 0 = disabled (default) +# 1 = enabled +#peerkey=1 + +# ieee80211w: Whether management frame protection (MFP) is enabled +# 0 = disabled (default) +# 1 = optional +# 2 = required +#ieee80211w=0 + +# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP) +# (maximum time to wait for a SA Query response) +# dot11AssociationSAQueryMaximumTimeout, 1...4294967295 +#assoc_sa_query_max_timeout=1000 + +# Association SA Query retry timeout (in TU = 1.024 ms; for MFP) +# (time between two subsequent SA Query requests) +# dot11AssociationSAQueryRetryTimeout, 1...4294967295 +#assoc_sa_query_retry_timeout=201 + +# disable_pmksa_caching: Disable PMKSA caching +# This parameter can be used to disable caching of PMKSA created through EAP +# authentication. RSN preauthentication may still end up using PMKSA caching if +# it is enabled (rsn_preauth=1). +# 0 = PMKSA caching enabled (default) +# 1 = PMKSA caching disabled +#disable_pmksa_caching=0 + +# okc: Opportunistic Key Caching (aka Proactive Key Caching) +# Allow PMK cache to be shared opportunistically among configured interfaces +# and BSSes (i.e., all configurations within a single hostapd process). +# 0 = disabled (default) +# 1 = enabled +#okc=1 + + +##### IEEE 802.11r configuration ############################################## + +# Mobility Domain identifier (dot11FTMobilityDomainID, MDID) +# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the +# same SSID) between which a STA can use Fast BSS Transition. +# 2-octet identifier as a hex string. +#mobility_domain=a1b2 + +# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID) +# 1 to 48 octet identifier. +# This is configured with nas_identifier (see RADIUS client section above). + +# Default lifetime of the PMK-RO in minutes; range 1..65535 +# (dot11FTR0KeyLifetime) +#r0_key_lifetime=10000 + +# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) +# 6-octet identifier as a hex string. +#r1_key_holder=000102030405 + +# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535) +# (dot11FTReassociationDeadline) +#reassociation_deadline=1000 + +# List of R0KHs in the same Mobility Domain +# format: <128-bit key as hex string> +# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC +# address when requesting PMK-R1 key from the R0KH that the STA used during the +# Initial Mobility Domain Association. +#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f +#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff +# And so on.. One line per R0KH. + +# List of R1KHs in the same Mobility Domain +# format: <128-bit key as hex string> +# This list is used to map R1KH-ID to a destination MAC address when sending +# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD +# that can request PMK-R1 keys. +#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f +#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff +# And so on.. One line per R1KH. + +# Whether PMK-R1 push is enabled at R0KH +# 0 = do not push PMK-R1 to all configured R1KHs (default) +# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived +#pmk_r1_push=1 + +##### Neighbor table ########################################################## +# Maximum number of entries kept in AP table (either for neigbor table or for +# detecting Overlapping Legacy BSS Condition). The oldest entry will be +# removed when adding a new entry that would make the list grow over this +# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is +# enabled, so this field should not be set to 0 when using IEEE 802.11g. +# default: 255 +#ap_table_max_size=255 + +# Number of seconds of no frames received after which entries may be deleted +# from the AP table. Since passive scanning is not usually performed frequently +# this should not be set to very small value. In addition, there is no +# guarantee that every scan cycle will receive beacon frames from the +# neighboring APs. +# default: 60 +#ap_table_expiration_time=3600 + + +##### Wi-Fi Protected Setup (WPS) ############################################# + +# WPS state +# 0 = WPS disabled (default) +# 1 = WPS enabled, not configured +# 2 = WPS enabled, configured +#wps_state=2 + +# AP can be configured into a locked state where new WPS Registrar are not +# accepted, but previously authorized Registrars (including the internal one) +# can continue to add new Enrollees. +#ap_setup_locked=1 + +# Universally Unique IDentifier (UUID; see RFC 4122) of the device +# This value is used as the UUID for the internal WPS Registrar. If the AP +# is also using UPnP, this value should be set to the device's UPnP UUID. +# If not configured, UUID will be generated based on the local MAC address. +#uuid=12345678-9abc-def0-1234-56789abcdef0 + +# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs +# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the +# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of +# per-device PSKs is recommended as the more secure option (i.e., make sure to +# set wpa_psk_file when using WPS with WPA-PSK). + +# When an Enrollee requests access to the network with PIN method, the Enrollee +# PIN will need to be entered for the Registrar. PIN request notifications are +# sent to hostapd ctrl_iface monitor. In addition, they can be written to a +# text file that could be used, e.g., to populate the AP administration UI with +# pending PIN requests. If the following variable is set, the PIN requests will +# be written to the configured file. +#wps_pin_requests=/var/run/hostapd_wps_pin_requests + +# Device Name +# User-friendly description of device; up to 32 octets encoded in UTF-8 +#device_name=Wireless AP + +# Manufacturer +# The manufacturer of the device (up to 64 ASCII characters) +#manufacturer=Company + +# Model Name +# Model of the device (up to 32 ASCII characters) +#model_name=WAP + +# Model Number +# Additional device description (up to 32 ASCII characters) +#model_number=123 + +# Serial Number +# Serial number of the device (up to 32 characters) +#serial_number=12345 + +# Primary Device Type +# Used format: -- +# categ = Category as an integer value +# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for +# default WPS OUI +# subcateg = OUI-specific Sub Category as an integer value +# Examples: +# 1-0050F204-1 (Computer / PC) +# 1-0050F204-2 (Computer / Server) +# 5-0050F204-1 (Storage / NAS) +# 6-0050F204-1 (Network Infrastructure / AP) +#device_type=6-0050F204-1 + +# OS Version +# 4-octet operating system version number (hex string) +#os_version=01020300 + +# Config Methods +# List of the supported configuration methods +# Available methods: usba ethernet label display ext_nfc_token int_nfc_token +# nfc_interface push_button keypad virtual_display physical_display +# virtual_push_button physical_push_button +#config_methods=label virtual_display virtual_push_button keypad + +# WPS capability discovery workaround for PBC with Windows 7 +# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting +# as a Registrar and using M1 from the AP. The config methods attribute in that +# message is supposed to indicate only the configuration method supported by +# the AP in Enrollee role, i.e., to add an external Registrar. For that case, +# PBC shall not be used and as such, the PushButton config method is removed +# from M1 by default. If pbc_in_m1=1 is included in the configuration file, +# the PushButton config method is left in M1 (if included in config_methods +# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label +# in the AP). +#pbc_in_m1=1 + +# Static access point PIN for initial configuration and adding Registrars +# If not set, hostapd will not allow external WPS Registrars to control the +# access point. The AP PIN can also be set at runtime with hostapd_cli +# wps_ap_pin command. Use of temporary (enabled by user action) and random +# AP PIN is much more secure than configuring a static AP PIN here. As such, +# use of the ap_pin parameter is not recommended if the AP device has means for +# displaying a random PIN. +#ap_pin=12345670 + +# Skip building of automatic WPS credential +# This can be used to allow the automatically generated Credential attribute to +# be replaced with pre-configured Credential(s). +#skip_cred_build=1 + +# Additional Credential attribute(s) +# This option can be used to add pre-configured Credential attributes into M8 +# message when acting as a Registrar. If skip_cred_build=1, this data will also +# be able to override the Credential attribute that would have otherwise been +# automatically generated based on network configuration. This configuration +# option points to an external file that much contain the WPS Credential +# attribute(s) as binary data. +#extra_cred=hostapd.cred + +# Credential processing +# 0 = process received credentials internally (default) +# 1 = do not process received credentials; just pass them over ctrl_iface to +# external program(s) +# 2 = process received credentials internally and pass them over ctrl_iface +# to external program(s) +# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and +# extra_cred be used to provide the Credential data for Enrollees. +# +# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file +# both for Credential processing and for marking AP Setup Locked based on +# validation failures of AP PIN. An external program is responsible on updating +# the configuration appropriately in this case. +#wps_cred_processing=0 + +# AP Settings Attributes for M7 +# By default, hostapd generates the AP Settings Attributes for M7 based on the +# current configuration. It is possible to override this by providing a file +# with pre-configured attributes. This is similar to extra_cred file format, +# but the AP Settings attributes are not encapsulated in a Credential +# attribute. +#ap_settings=hostapd.ap_settings + +# WPS UPnP interface +# If set, support for external Registrars is enabled. +#upnp_iface=br0 + +# Friendly Name (required for UPnP) +# Short description for end use. Should be less than 64 characters. +#friendly_name=WPS Access Point + +# Manufacturer URL (optional for UPnP) +#manufacturer_url=http://www.example.com/ + +# Model Description (recommended for UPnP) +# Long description for end user. Should be less than 128 characters. +#model_description=Wireless Access Point + +# Model URL (optional for UPnP) +#model_url=http://www.example.com/model/ + +# Universal Product Code (optional for UPnP) +# 12-digit, all-numeric code that identifies the consumer package. +#upc=123456789012 + +##### Wi-Fi Direct (P2P) ###################################################### + +# Enable P2P Device management +#manage_p2p=1 + +# Allow cross connection +#allow_cross_connection=1 + +#### TDLS (IEEE 802.11z-2010) ################################################# + +# Prohibit use of TDLS in this BSS +#tdls_prohibit=1 + +# Prohibit use of TDLS Channel Switching in this BSS +#tdls_prohibit_chan_switch=1 + +##### IEEE 802.11v-2011 ####################################################### + +# Time advertisement +# 0 = disabled (default) +# 2 = UTC time at which the TSF timer is 0 +#time_advertisement=2 + +# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004: +# stdoffset[dst[offset][,start[/time],end[/time]]] +#time_zone=EST5 + +##### IEEE 802.11u-2011 ####################################################### + +# Enable Interworking service +#interworking=1 + +# Access Network Type +# 0 = Private network +# 1 = Private network with guest access +# 2 = Chargeable public network +# 3 = Free public network +# 4 = Personal device network +# 5 = Emergency services only network +# 14 = Test or experimental +# 15 = Wildcard +#access_network_type=0 + +# Whether the network provides connectivity to the Internet +# 0 = Unspecified +# 1 = Network provides connectivity to the Internet +#internet=1 + +# Additional Step Required for Access +# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if +# RSN is used. +#asra=0 + +# Emergency services reachable +#esr=0 + +# Unauthenticated emergency service accessible +#uesa=0 + +# Venue Info (optional) +# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34. +# Example values (group,type): +# 0,0 = Unspecified +# 1,7 = Convention Center +# 1,13 = Coffee Shop +# 2,0 = Unspecified Business +# 7,1 Private Residence +#venue_group=7 +#venue_type=1 + +# Homogeneous ESS identifier (optional; dot11HESSID) +# If set, this shall be identifical to one of the BSSIDs in the homogeneous +# ESS and this shall be set to the same value across all BSSs in homogeneous +# ESS. +#hessid=BigJambox + +# Roaming Consortium List +# Arbitrary number of Roaming Consortium OIs can be configured with each line +# adding a new OI to the list. The first three entries are available through +# Beacon and Probe Response frames. Any additional entry will be available only +# through ANQP queries. Each OI is between 3 and 15 octets and is configured a +# a hexstring. +#roaming_consortium=021122 +#roaming_consortium=2233445566 + +##### Multiple BSSID support ################################################## +# +# Above configuration is using the default interface (wlan#, or multi-SSID VLAN +# interfaces). Other BSSIDs can be added by using separator 'bss' with +# default interface name to be allocated for the data packets of the new BSS. +# +# hostapd will generate BSSID mask based on the BSSIDs that are +# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is +# not the case, the MAC address of the radio must be changed before starting +# hostapd (ifconfig wlan0 hw ether ). If a BSSID is configured for +# every secondary BSS, this limitation is not applied at hostapd and other +# masks may be used if the driver supports them (e.g., swap the locally +# administered bit) +# +# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is +# specified using the 'bssid' parameter. +# If an explicit BSSID is specified, it must be chosen such that it: +# - results in a valid MASK that covers it and the dev_addr +# - is not the same as the MAC address of the radio +# - is not the same as any other explicitly specified BSSID +# +# Please note that hostapd uses some of the values configured for the first BSS +# as the defaults for the following BSSes. However, it is recommended that all +# BSSes include explicit configuration of all relevant configuration items. +# +#bss=wlan0_0 +#ssid=BigJambox +# most of the above items can be used here (apart from radio interface specific +# items, like channel) + +#bss=wlan0_1 +#bssid=BigJambox +# ... -- cgit v1.2.3-59-g8ed1b