linux-dev/arch/arm64/boot/dts/allwinner/Makefile, branch master

arm64: dts: allwinner: h616: Add X96 Mate TV box support

2022-07-09T18:08:53Z

The X96 Mate is an Allwinner H616 based TV box, featuring: - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU - 2GiB/4GiB RAM (fully usable!) - 16/32/64GiB eMMC - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported) - Unsupported Allwinner WiFi chip - 2 x USB 2.0 host ports - HDMI port - IR receiver - 5V/2A DC power supply via barrel plug Add a basic devicetree for it, with SD card and eMMC working, as well as serial and the essential peripherals, like the AXP PMIC. This DT is somewhat minimal, and should work on many other similar TV boxes with the Allwinner H616 chip. Signed-off-by: Andre Przywara Reviewed-by: Samuel Holland Signed-off-by: Jernej Skrabec Link: https://lore.kernel.org/r/20220708105235.3983266-8-andre.przywara@arm.com

arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

2022-07-09T18:08:53Z

The OrangePi Zero 2 is a development board with the new H616 SoC. It comes with the following features: - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU - 512MiB/1GiB DDR3 DRAM - AXP305 PMIC - Raspberry-Pi-1 compatible GPIO header - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports - 1 USB 2.0 host port - 1 USB 2.0 type C port (power supply + OTG) - MicroSD slot - on-board 2MiB bootable SPI NOR flash - 1Gbps Ethernet port (via RTL8211F PHY) - micro-HDMI port - (yet) unsupported Allwinner WiFi/BT chip Add the devicetree file describing the currently supported features. Signed-off-by: Andre Przywara Acked-by: Samuel Holland Signed-off-by: Jernej Skrabec Link: https://lore.kernel.org/r/20220708105235.3983266-7-andre.przywara@arm.com

arm64: dts: allwinner: h6: Add Tanix TX6 mini dts

2021-12-03T09:55:13Z

Tanix TX6 mini is less capable version of Tanix TX6 although it comes with some features not present on Tanix TX6. Basic specs: - H6 SoC - 2 GiB DDR3 RAM - HDMI - SPDIF - 2x USB - analogue audio - CVBS - SD card - IR remote - LED display - fast ethernet - XR819 wifi - 16 GiB eMMC Currently supported features doesn't differ that much from Tanix TX6, but that will change soon. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard

arm64: dts: allwinner: h5: Add NanoPi R1S H5 support

2021-05-18T15:17:57Z

The NanoPi R1S H5 is a open source board made by FriendlyElec. It has the following features: - Allwinner H5, Quad-core Cortex-A53 - 512MB DDR3 RAM - 10/100/1000M Ethernet x 2 - RTL8189ETV WiFi 802.11b/g/n - USB 2.0 host port (A) - MicroSD Slot - Serial Debug Port - 5V 2A DC power-supply Signed-off-by: Chukun Pan Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn

arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab

2021-01-06T16:49:58Z

PineTabs since Early Adopter batch will use a new LCD panel. Add device tree for PineTab with the new panel. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201224024001.19248-2-icenowy@aosc.io

arm64: allwinner: A100: add support for Allwinner Perf1 board

2020-08-25T08:50:53Z

A100 perf1 is an Allwinner A100-based SBC, with the following features: - 1GiB DDR3 DRAM - AXP803 PMIC - 2 USB 2.0 ports - MicroSD slot and on-board eMMC module - on-board Nand flash - ··· Adds initial support for it, including UART and PMU. Signed-off-by: Yangtao Li Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/30f4a3fc6ac84d05094e2c3b89d1dddc8ff6b7fc.1595572867.git.frank@allwinnertech.com

arm64: dts: allwinner: Add support for PinePhone revision 1.2

2020-07-06T05:11:51Z

Revision 1.2 should be the final production version of the PinePhone. It has most of the known HW quirks fixed. Interrupt to the magnetometer is routed correctly, in this revision. The bulk of the changes are in how modem and the USB-C HDMI bridge chip is powered and where the signals from the modem are connected. Also backlight intensity seemingly behaves differently, than on the 1.1 and 1.0 boards, and the PWM duty cycle where backlight starts to work is 10% (as tested on 2 1.2 PinePhones I have access to). Signed-off-by: Ondrej Jirman Link: https://lore.kernel.org/r/20200703194842.111845-3-megous@megous.com Signed-off-by: Maxime Ripard

arm64: dts: allwinner: Add initial support for Pine64 PinePhone

2020-02-27T13:04:16Z

At the moment PinePhone comes in two slightly incompatible variants: - 1.0: Early Developer Batch - 1.1: Braveheart Batch There will be at least one more incompatible variant in the very near future, so let's start by sharing the dtsi among multiple variants, right away, even though the HW description doesn't yet include the different bits. The differences between 1.0 and 1.1 are: change in pins that control the flash LED, differences in modem power status signal routing, and maybe some other subtler things, that have not been determined yet. This is a basic DT that includes only features that are already supported by mainline drivers. Co-developed-by: Samuel Holland Signed-off-by: Samuel Holland Co-developed-by: Martijn Braam Signed-off-by: Martijn Braam Co-developed-by: Luca Weiss Signed-off-by: Luca Weiss Signed-off-by: Bhushan Shah Signed-off-by: Icenowy Zheng Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard

arm64: dts: allwinner: a64: add support for PineTab

2020-02-10T07:57:41Z

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside. It includes the following peripherals: USB: - A microUSB Type-B port connected to the OTG-capable USB PHY of Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG functionality on this port. - A USB Type-A port is connected to the internal hub attached to the non-OTG USB PHY of Allwinner A64. - There are reserved pins for an external keyboard connected to the internal hub. Power: - The microUSB port has its Vbus connected to AXP803, mentioned above. - A DC jack (of a strange size, 2.5mm outer diameter) is connected to the ACIN of AXP803. - A Li-Polymer battery is connected to the battery pins of AXP803. Storage: - An tradition Pine64 eMMC slot is on the board, mounted with an eMMC module by factory. - An external microSD slot is hidden under a protect case. Display: - A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC. - A mini HDMI port. Input: - A touch panel attached to a Goodix GT9271 touch controller. - Volume keys connected to the LRADC of the A64 SoC. Camera: - An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC. - A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640. Audio: - A headphone jack is conencted to the SoC's internal codec. - A speaker connected is to the Line Out port of SoC's internal codec, via an amplifier. Misc: - Debug UART is muxed with the headphone jack, with the switch next to the microSD slot. - A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC. - Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the one in Pinebook. This commit adds a basically usable device tree for it, implementing most of the features mentioned above. HDMI is not supported now because bad LCD-HDMI coexistence situation of mainline A64 display driver, the front camera currently lacks a driver and a facility to share the bus with the rear one, and the accelerometer currently lacks a DT binding. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard

arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board

2020-01-06T22:24:05Z

The Libre Computer ALL-H5-CC board is an upgraded version of the ALL-H3-CC. Changes include: - Gigabit Ethernet via external RTL8211E Ethernet PHY - 16 MiB SPI NOR flash memory - PoE tap header - Line out jack removed Only H5 variant test samples were made available, and the vendor is not certain whether other SoC variants would be made or not. Furthermore the board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree simply includes the one for the ALL-H3-CC, and adds the changes on top. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard