linux-dev/drivers/char/tpm/Makefile, branch master

tpm: Add tpm_tis_i2c backend for tpm_tis_core

2022-08-03T20:56:20Z

Implement the TCG I2C Interface driver, as specified in the TCG PC Client Platform TPM Profile (PTP) specification for TPM 2.0 v1.04 revision 14, section 8, I2C Interface Definition. This driver supports Guard Times. That is, if required by the TPM, the driver has to wait by a vendor-specific time after each I2C read/write. The specific time is read from the TPM_I2C_INTERFACE_CAPABILITY register. Unfortunately, the TCG specified almost but not quite compatible register addresses. Therefore, the TIS register addresses need to be mapped to I2C ones. The locality is stripped because for now, only locality 0 is supported. Add a sanity check to I2C reads of e.g. TPM_ACCESS and TPM_STS. This is to detect communication errors and issues due to non-standard behaviour (E.g. the clock stretching quirk in the BCM2835, see 4dbfb5f4401f). In case the sanity check fails, attempt a retry. Co-developed-by: Johannes Holland Signed-off-by: Johannes Holland Co-developed-by: Amir Mizinski Signed-off-by: Amir Mizinski Signed-off-by: Alexander Steffen Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

char: tpm: add i2c driver for cr50

2021-02-16T08:40:27Z

Add TPM 2.0 compatible I2C interface for chips with cr50 firmware. The firmware running on the currently supported H1 MCU requires a special driver to handle its specific protocol, and this makes it unsuitable to use tpm_tis_core_* and instead it must implement the underlying TPM protocol similar to the other I2C TPM drivers. - All 4 bytes of status register must be read/written at once. - FIFO and burst count is limited to 63 and must be drained by AP. - Provides an interrupt to indicate when read response data is ready and when the TPM is finished processing write data. This driver is based on the existing infineon I2C TPM driver, which most closely matches the cr50 i2c protocol behavior. Signed-off-by: Duncan Laurie Signed-off-by: Stephen Boyd Signed-off-by: Fabien Lahoudere Signed-off-by: Adrian Ratiu Tested-by: Adrian Ratiu Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: tis: add support for MMIO TPM on SynQuacer

2020-10-01T21:21:02Z

When fitted, the SynQuacer platform exposes its SPI TPM via a MMIO window that is backed by the SPI command sequencer in the SPI bus controller. This arrangement has the limitation that only byte size accesses are supported, and so we'll need to provide a separate module that take this into account. Signed-off-by: Ard Biesheuvel Signed-off-by: Masahisa Kojima Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: Revert tpm_tis_spi_mod.ko to tpm_tis_spi.ko.

2020-02-17T18:46:34Z

Revert tpm_tis_spi_mod.ko back to tpm_tis_spi.ko as the rename could break user space scripts. This can be achieved by renaming tpm_tis_spi.c as tpm_tis_spi_main.c. Then tpm_tis_spi-y can be used inside the makefile. Cc: Andrey Pronin Cc: Stephen Boyd Cc: stable@vger.kernel.org # 5.5.x Fixes: 797c0113c9a4 ("tpm: tpm_tis_spi: Support cr50 devices") Reported-by: Alexander Steffen Tested-by: Alexander Steffen Reviewed-by: Stephen Boyd Signed-off-by: Jarkko Sakkinen

tpm: tpm_tis_spi: Support cr50 devices

2019-11-12T19:45:37Z

Add TPM2.0 PTP FIFO compatible SPI interface for chips with Cr50 firmware. The firmware running on the currently supported H1 Secure Microcontroller requires a special driver to handle its specifics: - need to ensure a certain delay between SPI transactions, or else the chip may miss some part of the next transaction - if there is no SPI activity for some time, it may go to sleep, and needs to be waken up before sending further commands - access to vendor-specific registers Cr50 firmware has a requirement to wait for the TPM to wakeup before sending commands over the SPI bus. Otherwise, the firmware could be in deep sleep and not respond. The method to wait for the device to wakeup is slightly different than the usual flow control mechanism described in the TCG SPI spec. Add a completion to tpm_tis_spi_transfer() before we start a SPI transfer so we can keep track of the last time the TPM driver accessed the SPI bus to support the flow control mechanism. Split the cr50 logic off into a different file to keep it out of the normal code flow of the existing SPI driver while making it all part of the same module when the code is optionally compiled into the same module. Export a new function, tpm_tis_spi_init(), and the associated read/write/transfer APIs so that we can do this. Make the cr50 code wrap the tpm_tis_spi_phy struct with its own struct to override the behavior of tpm_tis_spi_transfer() by supplying a custom flow control hook. This shares the most code between the core driver and the cr50 support without combining everything into the core driver or exporting module symbols. Signed-off-by: Andrey Pronin Cc: Andrey Pronin Cc: Duncan Laurie Cc: Jason Gunthorpe Cc: Arnd Bergmann Cc: Greg Kroah-Hartman Cc: Guenter Roeck Cc: Alexander Steffen Cc: Heiko Stuebner [swboyd@chromium.org: Replace boilerplate with SPDX tag, drop suspended bit and remove ifdef checks in cr50.h, migrate to functions exported in tpm_tis_spi.h, combine into one module instead of two] Signed-off-by: Stephen Boyd Tested-by: Heiko Stuebner Reviewed-by: Heiko Stuebner Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm/tpm_ftpm_tee: A driver for firmware TPM running inside TEE

2019-09-02T14:08:35Z

Add a driver for a firmware TPM running inside TEE. Documentation of the firmware TPM: https://www.microsoft.com/en-us/research/publication/ftpm-software-implementation-tpm-chip/ . Implementation of the firmware TPM: https://github.com/Microsoft/ms-tpm-20-ref/tree/master/Samples/ARM32-FirmwareTPM Tested-by: Ilias Apalodimas Tested-by: Thirupathaiah Annapureddy Signed-off-by: Thirupathaiah Annapureddy Co-authored-by: Sasha Levin Signed-off-by: Sasha Levin Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: factor out tpm 1.x duration calculation to tpm1-cmd.c

2018-11-13T11:46:29Z

Factor out TPM 1.x commands calculation into tpm1-cmd.c file. and change the prefix from tpm_ to tpm1_. No functional change is done here. Signed-off-by: Tomas Winkler Tested-by: Jarkko Sakkinen Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: sort objects in the Makefile

2018-11-13T11:46:29Z

Make the tpm Makefile a bit more in order by putting objects in one column. Signed-off-by: Tomas Winkler Tested-by: Jarkko Sakkinen Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: Move shared eventlog functions to common.c

2018-05-09T11:45:46Z

Functions and structures specific to TPM1 are renamed from tpm* to tpm1*. Signed-off-by: Thiebaud Weksteen Suggested-by: Jarkko Sakkinen Reviewed-by: Jarkko Sakkinen Tested-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: Move eventlog files to a subdirectory

2018-05-09T11:45:46Z

Signed-off-by: Thiebaud Weksteen Suggested-by: Jarkko Sakkinen Reviewed-by: Jarkko Sakkinen Tested-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen