linux-dev/drivers/dma/dw-edma, branch master

dmaengine: dw-edma: Remove runtime PM support

2022-09-29T17:16:08Z

Currently, the dw-edma driver enables the runtime_pm for parent device (chip->dev) and increments/decrements the refcount during alloc/free chan resources callbacks. This leads to a problem when the eDMA driver has been probed, but the channels were not used. This scenario can happen when the DW PCIe driver probes eDMA driver successfully, but the PCI EPF driver decides not to use eDMA channels and use iATU instead for PCI transfers. In this case, the underlying device would be runtime suspended due to pm_runtime_enable() in dw_edma_probe() and the PCI EPF driver would have no knowledge of it. Ideally, the eDMA driver should not be the one doing the runtime PM of the parent device. The responsibility should instead belong to the client drivers like PCI EPF. So let's remove the runtime PM support from eDMA driver. Cc: Serge Semin Cc: Frank Li Reviewed-by: Serge Semin Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20220910054700.12205-1-manivannan.sadhasivam@linaro.org Signed-off-by: Vinod Koul

Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

2022-08-05T02:30:35Z

Pull pci updates from Bjorn Helgaas: "Enumeration: - Consolidate duplicated 'next function' scanning and extend to allow 'isolated functions' on s390, similar to existing hypervisors (Niklas Schnelle) Resource management: - Implement pci_iobar_pfn() for sparc, which allows us to remove the sparc-specific pci_mmap_page_range() and pci_mmap_resource_range(). This removes the ability to map the entire PCI I/O space using /proc/bus/pci, but we believe that's already been broken since v2.6.28 (Arnd Bergmann) - Move common PCI definitions to asm-generic/pci.h and rework others to be be more specific and more encapsulated in arches that need them (Stafford Horne) Power management: - Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas) Virtualization: - Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate the functions but don't advertise an ACS capability (Pavan Chebbi) Error handling: - Clear PCI Status register during enumeration in case firmware left errors logged (Kai-Heng Feng) - When we have native control of AER, enable error reporting for all devices that support AER. Previously only a few drivers enabled this (Stefan Roese) - Keep AER error reporting enabled for switches. Previously we enabled this during enumeration but immediately disabled it (Stefan Roese) - Iterate over error counters instead of error strings to avoid printing junk in AER sysfs counters (Mohamed Khalfella) ASPM: - Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g., via sysfs, are not lost across power state changes (Kai-Heng Feng) Endpoint framework: - Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie) Endpoint embedded DMA controller driver: - Simplify and clean up support for the DesignWare embedded DMA (eDMA) controller (Frank Li, Serge Semin) Broadcom STB PCIe controller driver: - Avoid config space accesses when link is down because we can't recover from the CPU aborts these cause (Jim Quinlan) - Look for power regulators described under Root Ports in DT and enable them before scanning the secondary bus (Jim Quinlan) - Disable/enable regulators in suspend/resume (Jim Quinlan) Freescale i.MX6 PCIe controller driver: - Simplify and clean up clock and PHY management (Richard Zhu) - Disable/enable regulators in suspend/resume (Richard Zhu) - Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu) - Allow speeds faster than Gen2 (Richard Zhu) - Make link being down a non-fatal error so controller probe doesn't fail if there are no Endpoints connected (Richard Zhu) Loongson PCIe controller driver: - Add ACPI and MCFG support for Loongson LS7A (Huacai Chen) - Avoid config reads to non-existent LS2K/LS7A devices because a hardware defect causes machine hangs (Huacai Chen) - Work around LS7A integrated devices that report incorrect Interrupt Pin values (Jianmin Lv) Marvell Aardvark PCIe controller driver: - Add support for AER and Slot capability on emulated bridge (Pali Rohár) MediaTek PCIe controller driver: - Add Airoha EN7532 to DT binding (John Crispin) - Allow building of driver for ARCH_AIROHA (Felix Fietkau) MediaTek PCIe Gen3 controller driver: - Print decoded LTSSM state when the link doesn't come up (Jianjun Wang) NVIDIA Tegra194 PCIe controller driver: - Convert DT binding to json-schema (Vidya Sagar) - Add DT bindings and driver support for Tegra234 Root Port and Endpoint mode (Vidya Sagar) - Fix some Root Port interrupt handling issues (Vidya Sagar) - Set default Max Payload Size to 256 bytes (Vidya Sagar) - Fix Data Link Feature capability programming (Vidya Sagar) - Extend Endpoint mode support to devices beyond Controller-5 (Vidya Sagar) Qualcomm PCIe controller driver: - Rework clock, reset, PHY power-on ordering to avoid hangs and improve consistency (Robert Marko, Christian Marangi) - Move pipe_clk handling to PHY drivers (Dmitry Baryshkov) - Add IPQ60xx support (Selvam Sathappan Periakaruppan) - Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru) - Add support for more than 32 MSI interrupts (Dmitry Baryshkov) Renesas R-Car PCIe controller driver: - Convert DT binding to json-schema (Herve Codina) - Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver (Herve Codina) Samsung Exynos PCIe controller driver: - Fix phy-exynos-pcie driver so it follows the 'phy_init() before phy_power_on()' PHY programming model (Marek Szyprowski) Synopsys DesignWare PCIe controller driver: - Simplify and clean up the DWC core extensively (Serge Semin) - Fix an issue with programming the ATU for regions that cross a 4GB boundary (Serge Semin) - Enable the CDM check if 'snps,enable-cdm-check' exists; previously we skipped it if 'num-lanes' was absent (Serge Semin) - Allocate a 32-bit DMA-able page to be MSI target instead of using a driver data structure that may not be addressable with 32-bit address (Will McVicker) - Add DWC core support for more than 32 MSI interrupts (Dmitry Baryshkov) Xilinx Versal CPM PCIe controller driver: - Add DT binding and driver support for Versal CPM5 Gen5 Root Port (Bharat Kumar Gogada)" * tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits) PCI: imx6: Support more than Gen2 speed link mode PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers PCI: imx6: Reformat suspend callback to keep symmetric with resume PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier PCI: imx6: Disable clocks in reverse order of enable PCI: imx6: Do not hide PHY driver callbacks and refine the error handling PCI: imx6: Reduce resume time by only starting link if it was up before suspend PCI: imx6: Mark the link down as non-fatal error PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset() PCI: imx6: Turn off regulator when system is in suspend mode PCI: imx6: Call host init function directly in resume PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks PCI: imx6: Propagate .host_init() errors to caller PCI: imx6: Collect clock enables in imx6_pcie_clk_enable() PCI: imx6: Factor out ref clock disable to match enable PCI: imx6: Move imx6_pcie_clk_disable() earlier PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier PCI: imx6: Move PHY management functions together PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS() ...

dmaengine: dw-edma: Add support for chip-specific flags

2022-06-23T19:56:34Z

Add a "flags" field to the "struct dw_edma_chip" so that the controller drivers can pass flags that are relevant to the platform. DW_EDMA_CHIP_LOCAL - Used by the controller drivers accessing eDMA locally. Local eDMA access doesn't require generating MSIs to the remote. Link: https://lore.kernel.org/r/20220524152159.2370739-8-Frank.Li@nxp.com Tested-by: Serge Semin Tested-by: Manivannan Sadhasivam Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Reviewed-by: Serge Semin Reviewed-by: Manivannan Sadhasivam Acked-By: Vinod Koul

dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics

2022-06-23T19:56:34Z

In accordance with [1, 2] the DW eDMA controller has been created to be part of the DW PCIe Root Port and DW PCIe End-point controllers and to offload the transferring of large blocks of data between application and remote PCIe domains leaving the system CPU free for other tasks. In the first case (eDMA being part of DW PCIe Root Port) the eDMA controller is always accessible via the CPU DBI interface and never over the PCIe wire. The latter case is more complex. Depending on the DW PCIe End-Point IP-core synthesize parameters it's possible to have the eDMA registers accessible not only from the application CPU side, but also via mapping the eDMA CSRs over a dedicated endpoint BAR. So based on the specifics denoted above the eDMA driver is supposed to support two types of the DMA controller setups: 1) eDMA embedded into the DW PCIe Root Port/End-point and accessible over the local CPU from the application side. 2) eDMA embedded into the DW PCIe End-point and accessible via the PCIe wire with MWr/MRd TLPs generated by the CPU PCIe host controller. Since the CPU memory resides different sides in these cases the semantics of the MEM_TO_DEV and DEV_TO_MEM operations is flipped with respect to the Tx and Rx DMA channels. So MEM_TO_DEV/DEV_TO_MEM corresponds to the Tx/Rx channels in setup 1) and to the Rx/Tx channels in case of setup 2). The DW eDMA driver has supported the case 2) since e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver") in the framework of the drivers/dma/dw-edma/dw-edma-pcie.c driver. The case 1) support was added later by bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics"). Afterwards the driver was supposed to cover the both possible eDMA setups, but the latter commit turned out to be not fully correct. The problem was that the commit together with the new functionality support also changed the channel direction semantics so the eDMA Read-channel (corresponding to the DMA_DEV_TO_MEM direction for case 1) now uses the sgl/cyclic base addresses as the Source addresses of the DMA transfers and dma_slave_config.dst_addr as the Destination address of the DMA transfers. Similarly the eDMA Write-channel (corresponding to the DMA_MEM_TO_DEV direction for case 1) now uses dma_slave_config.src_addr as a source address of the DMA transfers and sgl/cyclic base address as the Destination address of the DMA transfers. This contradicts the logic of the DMA-interface, which implies that DEV side is supposed to belong to the PCIe device memory and MEM - to the CPU/Application memory. Indeed it seems irrational to have the SG-list defined in the PCIe bus space, while expecting a contiguous buffer allocated in the CPU memory. Moreover the passed SG-list and cyclic DMA buffers are supposed to be mapped in a way so to be seen by the DW eDMA Application (CPU) interface. So in order to have the correct DW eDMA interface we need to invert the eDMA Rd/Wr-channels and DMA-slave directions semantics by selecting the src/dst addresses based on the DMA transfer direction instead of using the channel direction capability. [1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port, v.5.40a, March 2019, p.1092 [2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint, v.5.40a, March 2019, p.1189 Co-developed-by: Manivannan Sadhasivam Fixes: bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics") Link: https://lore.kernel.org/r/20220524152159.2370739-7-Frank.Li@nxp.com Tested-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam Signed-off-by: Serge Semin Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Acked-By: Vinod Koul

dmaengine: dw-edma: Drop dma_slave_config.direction field usage

2022-06-23T19:56:34Z

The dma_slave_config.direction field usage in the DW eDMA driver was introduced by bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics"). Mainly the change introduced there was correct (indeed DEV_TO_MEM means using RD-channel and MEM_TO_DEV - WR-channel for the case of having eDMA accessed locally from CPU/Application side), but providing an additional MEM_TO_MEM/DEV_TO_DEV-based semantics was quite redundant if not to say potentially harmful (when it comes to removing the denoted field). First of all since the dma_slave_config.direction field has been marked as obsolete (see [1] and the struct dma_slave_config [2]) and will be discarded in future, using it especially in a non-standard way is discouraged. Secondly in accordance with the commit denoted above the default dw_edma_device_transfer() semantics has been changed despite what its message said. So claiming that the method was left backward compatible was wrong. Fix the problems denoted above and simplify the dw_edma_device_transfer() method by dropping the parsing of the DMA-channel direction field. Instead of having that implicit dma_slave_config.direction field semantic, use the recently added DW_EDMA_CHIP_LOCAL flag to distinguish between the local and remote DW eDMA setups thus preserving support for both cases. Add an ASCII figure to clarify the situation. [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/driver-api/dmaengine/provider.rst?id=v5.18#n478 [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/dmaengine.h?id=v5.18#n389 [bhelgaas: convert references to specific URLs] Co-developed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20220524152159.2370739-6-Frank.Li@nxp.com Tested-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam Signed-off-by: Serge Semin Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Acked-By: Vinod Koul

dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

2022-06-23T19:56:34Z

The struct dw_edma contains wr(rd)_ch_cnt fields. The EDMA driver gets write(read) channel number from register, then saves these into dw_edma. The wr(rd)_ch_cnt in dw_edma_chip actually means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. Rename it to ll_wr(rd)_cnt to indicate actual usage. Link: https://lore.kernel.org/r/20220524152159.2370739-5-Frank.Li@nxp.com Tested-by: Serge Semin Tested-by: Manivannan Sadhasivam Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Reviewed-by: Serge Semin Reviewed-by: Manivannan Sadhasivam Acked-By: Vinod Koul

dmaengine: dw-edma: Change rg_region to reg_base in struct dw_edma_chip

2022-06-23T19:56:34Z

struct dw_edma_region rg_region included virtual address, physical address and size information. But only the virtual address is used by EDMA driver. Change it to void __iomem *reg_base to clean up code. Link: https://lore.kernel.org/r/20220524152159.2370739-4-Frank.Li@nxp.com Tested-by: Serge Semin Tested-by: Manivannan Sadhasivam Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Reviewed-by: Serge Semin Reviewed-by: Manivannan Sadhasivam Acked-By: Vinod Koul

dmaengine: dw-edma: Detach the private data and chip info structures

2022-06-23T19:49:30Z

"struct dw_edma_chip" contains an internal structure "struct dw_edma" that is used by the eDMA core internally and should not be touched by the eDMA controller drivers themselves. But currently, the eDMA controller drivers like "dw-edma-pci" allocate and populate this internal structure before passing it on to the eDMA core. The eDMA core further populates the structure and uses it. This is wrong! Hence, move all the "struct dw_edma" specifics from controller drivers to the eDMA core. Link: https://lore.kernel.org/r/20220524152159.2370739-3-Frank.Li@nxp.com Tested-by: Serge Semin Tested-by: Manivannan Sadhasivam Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Reviewed-by: Serge Semin Reviewed-by: Manivannan Sadhasivam Acked-By: Vinod Koul

dmaengine: dw-edma: Remove unused irq field in struct dw_edma_chip

2022-06-16T16:31:05Z

The "irq" field of struct dw_edma_chip was never used. Remove it. Link: https://lore.kernel.org/r/20220524152159.2370739-2-Frank.Li@nxp.com Tested-by: Serge Semin Tested-by: Manivannan Sadhasivam Signed-off-by: Frank Li Signed-off-by: Bjorn Helgaas Reviewed-by: Serge Semin Reviewed-by: Manivannan Sadhasivam Acked-By: Vinod Koul

dmaengine: dw-edma: remove a macro conditional with similar branches

2022-06-10T13:49:24Z

After adding commit 8fc5133d6d4d ("dmaengine: dw-edma: Fix unaligned 64bit access") two branches under macro conditional become identical, thus the code can be simplified without any functional change. Signed-off-by: Vladimir Zapolskiy Acked-by: Herve Codina Link: https://lore.kernel.org/r/20220610100700.2295522-1-vladimir.zapolskiy@linaro.org Signed-off-by: Vinod Koul