linux-dev/drivers/firmware/arm_scmi/Makefile, branch master

firmware: arm_scmi: Add SCMI v3.1 powercap protocol basic support

2022-07-04T13:28:42Z

Add support for SCMI v3.1 powercap protocol, with the exception of powercap fast channels, exposing all the new related powercap protocol operations as usual in include/linux/scmi_protocol.h. Link: https://lore.kernel.org/r/20220704102241.2988447-3-cristian.marussi@arm.com Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Add SCMI System Power Control driver

2022-07-04T13:28:42Z

Add an SCMI System Power control driver to handle platform's requests carried by SYSTEM_POWER_STATE_NOTIFIER notifications: such platform requested system-wide power state transitions are handled accordingly, gracefully or forcefully, depending on the notifications' message flags. Graceful requests are relayed to userspace using the same Kernel API used to handle ACPI Shutdown bus events. Link: https://lore.kernel.org/r/20220704101933.2981635-5-cristian.marussi@arm.com Reviewed-by: Greg Kroah-Hartman Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Disable ftrace for Clang Thumb2 builds

2022-02-08T23:06:40Z

The SMC calling convention designates R0-R7 as input registers in AArch32 mode, and this conflicts with the compiler's use of R7 as a frame pointer when building in Thumb2 mode. Generally, we don't enable the frame pointer, and GCC happily enables the -pg profiling hooks without them. However, Clang refuses, and errors out with the message below: drivers/firmware/arm_scmi/smc.c:152:2: error: write to reserved register 'R7' arm_smccc_1_1_invoke(scmi_info->func_id, 0, 0, 0, 0, 0, 0, 0, &res); ^ include/linux/arm-smccc.h:550:4: note: expanded from macro 'arm_smccc_1_1_invoke' arm_smccc_1_1_smc(__VA_ARGS__); \ ^ Let's just disable ftrace for the compilation unit when building this configuration. Link: https://lore.kernel.org/r/20220203082204.1176734-11-ardb@kernel.org Reviewed-by: Nick Desaulniers Signed-off-by: Ard Biesheuvel Signed-off-by: Sudeep Holla

firmware: arm_scmi: Add optee transport

2021-11-17T11:24:51Z

Add a new transport channel to the SCMI firmware interface driver for SCMI message exchange based on optee transport channel. The optee transport is realized by connecting and invoking OP-TEE SCMI service interface PTA. Optee transport support (CONFIG_ARM_SCMI_TRANSPORT_OPTEE) is default enabled when optee driver (CONFIG_OPTEE) is enabled. Effective optee transport is setup upon OP-TEE SCMI service discovery at optee device initialization. For this SCMI UUID is registered to the optee bus for probing. This is done from the link_supplier operator of the SCMI optee transport. The optee transport can use a statically defined shared memory in which case SCMI device tree node defines it using an "arm,scmi-shmem" compatible phandle through property shmem. Alternatively, optee transport allocates the shared memory buffer from the optee driver when no shmem property is defined. The protocol used to exchange SCMI message over that shared memory is negotiated between optee transport driver and the OP-TEE service through capabilities exchange. OP-TEE SCMI service is integrated in OP-TEE since its release tag 3.13.0. The service interface is published in [1]. Link: [1] https://github.com/OP-TEE/optee_os/blob/3.13.0/lib/libutee/include/pta_scmi_client.h Link: https://lore.kernel.org/r/20211028140009.23331-2-etienne.carriere@linaro.org Cc: Cristian Marussi Cc: Sudeep Holla Reviewed-by: Cristian Marussi Signed-off-by: Etienne Carriere Signed-off-by: Sudeep Holla

firmware: arm_scmi: Add virtio transport

2021-08-05T09:24:08Z

This transport enables communications with an SCMI platform through virtio; the SCMI platform will be represented by a virtio device. Implement an SCMI virtio driver according to the virtio SCMI device spec [1]. Virtio device id 32 has been reserved for the SCMI device [2]. The virtio transport has one Tx channel (virtio cmdq, A2P channel) and at most one Rx channel (virtio eventq, P2A channel). The following feature bit defined in [1] is not implemented: VIRTIO_SCMI_F_SHARED_MEMORY. The number of messages which can be pending simultaneously is restricted according to the virtqueue capacity negotiated at probing time. As soon as Rx channel message buffers are allocated or have been read out by the arm-scmi driver, feed them back to the virtio device. Since some virtio devices may not have the short response time exhibited by SCMI platforms using other transports, set a generous response timeout. SCMI polling mode is not supported by this virtio transport since deemed meaningless: polling mode operation is offered by the SCMI core to those transports that could not provide a completion interrupt on the TX path, which is never the case for virtio whose core callbacks can easily call into core scmi_rx_callback upon messages reception. [1] https://github.com/oasis-tcs/virtio-spec/blob/master/virtio-scmi.tex [2] https://www.oasis-open.org/committees/ballot.php?id=3496 Link: https://lore.kernel.org/r/20210803131024.40280-16-cristian.marussi@arm.com Cc: "Michael S. Tsirkin" Cc: Jason Wang Co-developed-by: Peter Hilber Co-developed-by: Cristian Marussi Signed-off-by: Igor Skalkin [ Peter: Adapted patch for submission to upstream. ] Signed-off-by: Peter Hilber [ Cristian: simplified driver logic, changed link_supplier and channel available/setup logic, removed dummy callbacks ] Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Add message passing abstractions for transports

2021-08-05T09:23:23Z

Add abstractions for future transports using message passing, such as virtio. Derive the abstractions from the shared memory abstractions. Abstract the transport SDU through the opaque struct scmi_msg_payld. Also enable the transport to determine all other required information about the transport SDU. Link: https://lore.kernel.org/r/20210803131024.40280-12-cristian.marussi@arm.com Signed-off-by: Peter Hilber [ Cristian: Adapted to new SCMI Kconfig layout, updated Copyrights ] Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Make shmem support optional for transports

2021-08-05T09:23:23Z

Upcoming new SCMI transports won't need any kind of shared memory support. Compile shmem.c only if a shmem based transport is selected. Link: https://lore.kernel.org/r/20210803131024.40280-10-cristian.marussi@arm.com Co-developed-by: Peter Hilber Signed-off-by: Igor Skalkin [ Peter: Adapted patch for submission to upstream. ] Signed-off-by: Peter Hilber [ Cristian: Adapted patch/commit_msg to new SCMI Kconfig layout ] Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Make SCMI transports configurable

2021-08-05T09:23:22Z

Add configuration options to be able to select which SCMI transports have to be compiled into the SCMI stack. Mailbox and SMC are by default enabled if their related dependencies are satisfied. While doing that move all SCMI related config options in their own dedicated submenu. Link: https://lore.kernel.org/r/20210803131024.40280-9-cristian.marussi@arm.com Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Add voltage domain management protocol support

2020-11-20T14:55:48Z

SCMI v3.0 introduces voltage domain protocol which provides commands to: - Discover the voltage levels supported by a domain - Get the configuration and voltage level of a domain - Set the configuration and voltage level of a domain Let us add support for the same. Link: https://lore.kernel.org/r/20201119191051.46363-2-cristian.marussi@arm.com Signed-off-by: Cristian Marussi Signed-off-by: Sudeep Holla

firmware: arm_scmi: Enable building as a single module

2020-09-14T06:31:03Z

Now, with all the plumbing in place to enable building scmi as a module instead of built-in modules, let us enable the same. Link: https://lore.kernel.org/r/20200907195046.56615-5-sudeep.holla@arm.com Tested-by: Cristian Marussi Signed-off-by: Sudeep Holla