linux-dev/drivers/gpu/drm/amd/display/dmub, branch linus/master

drm/amd/display: Fix DMUB outbox trace in S4 (#4465)

2022-06-01T19:56:48Z

[Why] DMUB Outbox0 read/write pointer not sync after resumed from S4. And that caused old traces were sent to outbox. [How] Disable DMUB Outbox0 interrupt and clear DMUB Outbox0 read/write pointer when resumes from S4. And then enable Outbox0 interrupt before starts DMCUB. Reviewed-by: Nicholas Kazlauskas Acked-by: Jasdeep Dhillon Tested-by: Daniel Wheeler Signed-off-by: Cruise Hung Signed-off-by: Alex Deucher

drm/amd/display: Wait DMCUB to idle state before reset.

2022-06-01T19:56:48Z

[WHY] Very low rate to cause memory access issue while resetting DMCUB after the halt command was sent to it. The process of stopping fw of DMCUB may be timeout, that means it is not in idle state, such as the window frames may still be kept in cache, so reset by force will cause MMHUB hang. [HOW] After the halt command was sent, keep checking the DMCUB state until it is idle. Reviewed-by: Eric Yang Reviewed-by: Nicholas Kazlauskas Acked-by: Jasdeep Dhillon Tested-by: Daniel Wheeler Signed-off-by: hengzhou Signed-off-by: Alex Deucher

drm/amd/display: [FW Promotion] Release 0.0.115.0

2022-05-04T14:43:55Z

- Add new cmd for querying HPD state Reviewed-by: Aric Cyr Acked-by: Wayne Lin Signed-off-by: Anthony Koo Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher

drm/amd/display: Add Connection Manager boot option.

2022-05-04T14:43:55Z

[Why] Boot up behaviour may differ depending on the Connection Manager handling USB4 tunneling. [How] Send boot option to firmware to indicate Connection Manager. Reviewed-by: Jun Lei Acked-by: Wayne Lin Signed-off-by: Jimmy Kizito Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher

drm/amd/display: [FW Promotion] Release 0.0.111.0

2022-04-05T14:29:48Z

- Add options to allow for configurable PHY options during PSR active state - Remove unused versioning and git hash Tested-by: Daniel Wheeler Reviewed-by: Aric Cyr Acked-by: Tom Chung Signed-off-by: Anthony Koo Signed-off-by: Alex Deucher

drm/amd/display: Fix unused-but-set-variable warning

2022-04-05T14:26:36Z

Fix the kernel test robot warning below: drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2893:12: warning: variable 'temp' set but not used [-Wunused-but-set-variable] Replaced the assignment to the unused temp variable with READ_ONCE() macro to flush the writes. READ_ONCE() helps avoid the use of volatile and makes it obvious from the code that the read here is intentional. Also verified on x86 that the generated code is exactly the same as before. Reported-by: kernel test robot Signed-off-by: Aashish Sharma Signed-off-by: Alex Deucher

drm/amd/display: [FW Promotion] Release 0.0.110.0

2022-04-01T03:05:53Z

- Revert save/restore PANEL_PWRSEQ_REF_DIV2 and other psr phy optimizations Reviewed-by: Aric Cyr Acked-by: Alex Hung Signed-off-by: Anthony Koo Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher

drm/amd/display: [FW Promotion] Release 0.0.109.0

2022-03-25T16:40:26Z

Reviewed-by: Aric Cyr Acked-by: Alex Hung Signed-off-by: Anthony Koo Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher

drm/amd/display: [FW Promotion] Release 0.0.108.0

2022-03-15T18:42:07Z

Reviewed-by: Aric Cyr Acked-by: Agustin Gutierrez Signed-off-by: Anthony Koo Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher

drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2

2022-03-15T18:42:01Z

[why] DCN31 has this in zstate save/restore sequence. need for non_zstate supported ASIC [how] add this PANEL_PWRSEQ_REF_DIV2 to existing panel_cntl_hw_init structure. Reviewed-by: Nicholas Kazlauskas Acked-by: Agustin Gutierrez Signed-off-by: Charlene Liu Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher