linux-dev/drivers/iio/imu/Kconfig, branch linus/master

iio: st_sensors: Add lsm9ds0 IMU support

2021-05-17T12:54:22Z

We can utilize separate drivers for accelerometer and magnetometer, so here is the glue driver to enable LSM9DS0 IMU support. The idea was suggested by Crestez Dan Leonard in [1]. The proposed change was sent as RFC due to race condition concerns, which are indeed possible. In order to amend the initial change, I went further by providing a specific multi-instantiate probe driver that reuses existing accelerometer and magnetometer. [1]: https://lore.kernel.org/patchwork/patch/670353/ Suggested-by: Crestez Dan Leonard Cc: mr.lahorde@laposte.net Cc: Matija Podravec Cc: Sergey Borishchenko Signed-off-by: Andy Shevchenko Link: https://lore.kernel.org/r/20210414195454.84183-6-andriy.shevchenko@linux.intel.com Signed-off-by: Jonathan Cameron

iio: imu: add Kconfig and Makefile for inv_icm42600 driver

2020-06-27T13:20:25Z

Add 3 modules: inv-icm42600, inv-icm42600-i2c, inv-icm42600-spi. Signed-off-by: Jean-Baptiste Maneyrol Signed-off-by: Jonathan Cameron

iio: imu: Add support for adis16475

2020-05-03T08:47:18Z

Support ADIS16475 and similar IMU devices. These devices are a precision, miniature MEMS inertial measurement unit (IMU) that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor combines with signal conditioning that optimizes dynamic performance. The driver adds support for the following devices: * adis16470, adis16475, adis16477, adis16465, adis16467, adis16500, adis16505, adis16507. Signed-off-by: Nuno Sá Signed-off-by: Jonathan Cameron

iio: imu: Add support for the FXOS8700 IMU

2019-10-22T09:24:50Z

FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis magnetometer combined into a single package. The device features a selectable I2C or point-to-point SPI serial interface with 14-bit accelerometer and 16-bit magnetometer ADC resolution along with smart-embedded functions. FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of ±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT. Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user for each sensor. Interleaved magnetic and acceleration data is available at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN package and it is guaranteed to operate over the extended temperature range of –40 °C to +85 °C. TODO: Trigger and IRQ configuration support Datasheet: http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf Signed-off-by: Robert Jones Signed-off-by: Jonathan Cameron

iio: imu: Add support for the ADIS16460 IMU

2019-07-27T21:52:06Z

The ADIS16460 device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. It's more simplified design than that of the ADIS16480, and does not offer the triaxial magnetometers & pressure sensors. It does also have a temperature sensor (like the ADIS16480). Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS library. Naturally, the register map is different and much more simplified than the ADIS16480 subfamily, so it cannot be integrated into that driver. A major difference is that the registers are not paged. One thing that is particularly special about it, is that it requires a higher delay between CS changes (i.e. when CS goes up, the spec recommends that it be brought down after a minimum of 16 uS). Other ADIS chips require (via spec) a minimum of 2 uS between CS changes. The kernel's 10 uS default should be fine for those other chips; they haven't been tested with lower CS change delays yet. Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdf Signed-off-by: Dragos Bogdan Signed-off-by: Michael Hennerich Signed-off-by: Alexandru Ardelean Signed-off-by: Jonathan Cameron

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46Z

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

iio: imu: add support to lsm6dsx driver

2017-01-14T12:40:37Z

Add support to STM LSM6DS3-LSM6DSM 6-axis (acc + gyro) Mems sensor http://www.st.com/resource/en/datasheet/lsm6ds3.pdf http://www.st.com/resource/en/datasheet/lsm6dsm.pdf - continuous mode support - i2c support - spi support - sw fifo mode support - supported devices: lsm6ds3, lsm6dsm Signed-off-by: Lorenzo Bianconi Signed-off-by: Jonathan Cameron

iio: imu: Add initial support for Bosch BMI160

2016-04-16T12:39:21Z

BMI160 is an Inertial Measurement Unit (IMU) which provides acceleration and angular rate measurement. It also offers a secondary I2C interface for connecting a magnetometer sensor (usually BMM160). Current driver offers support for accelerometer and gyroscope readings via sysfs or via buffer interface using an external trigger (e.g. hrtimer). Data is retrieved from IMU via I2C or SPI interface. Datasheet is at: http://www.mouser.com/ds/2/783/BST-BMI160-DS000-07-786474.pdf Signed-off-by: Daniel Baluta Signed-off-by: Jonathan Cameron

iio: imu: kmx61: Add support for data ready triggers

2014-12-12T13:49:30Z

This creates a data ready trigger per IIO device. Signed-off-by: Daniel Baluta Signed-off-by: Jonathan Cameron

iio: imu: Add support for Kionix KMX61 sensor

2014-12-12T13:43:54Z

Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports raw accel/magn readings together with scale and sampling frequency. This driver uses two IIO devices one for accelerometer and one for magnetometer. Datasheet will be available at: http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61 Signed-off-by: Daniel Baluta Signed-off-by: Jonathan Cameron