linux-dev/drivers/media/platform/rockchip, branch master

media: drivers: use video device pipeline start/stop

2022-09-24T07:14:20Z

Convert the media drivers to use video device based pipeline start/stop where possible. Signed-off-by: Tomi Valkeinen Reviewed-by: Laurent Pinchart Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

media: mc: entity: Rename streaming_count -> start_count

2022-09-24T07:09:05Z

'streaming_count' is a bit misleading name, as the count is increased with media_pipeline_start(). Let's rename it to 'start_count' instead. Signed-off-by: Tomi Valkeinen Reviewed-by: Laurent Pinchart Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Zero v4l2_subdev_format fields in when validating links

2022-09-24T06:42:42Z

The local sd_fmt variable in rkisp1_capture_link_validate() has uninitialized fields, which causes random failures when calling the subdev .get_fmt() operation. Fix it by initializing the variable when declaring it, which zeros all other fields. Signed-off-by: Laurent Pinchart Reviewed-by: Paul Elder Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Configure LSC after enabling the ISP

2022-09-24T06:42:16Z

The ISP8000Nano v18.02 (found in the i.MX8MP) requires the ISP to be enabled (as indicated by the ISP_CTRL.ISP_ENABLE bit) to configure the lens shading table in internal RAM. The driver currently configures all ISP initial parameters before enabling the ISP, which causes the LSC RAM to not be initialized properly. To fix this, split the rkisp1_params_configure() function into a rkisp1_params_pre_configure() and a rkisp1_params_post_configure(). The former configures all ISP parameters but LSC, while the latter configures LSC. To implement this, the rkisp1_params_apply_params_cfg() function is deconstructed, with two small helpers created to deal with the parameters buffers, which are then used in rkisp1_params_isr(), rkisp1_params_pre_configure() and rkisp1_params_post_configure(). While this initialization ordering is only needed for the ISP8000Nano v18.02, it doesn't affect other ISP versions negatively, and can thus be followed unconditionally. Signed-off-by: Laurent Pinchart Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Use correct macro for gradient registers

2022-09-24T06:41:31Z

The rkisp1_lsc_config() function incorrectly uses the RKISP1_CIF_ISP_LSC_SECT_SIZE() macro for the gradient registers. Replace it with the correct macro, and rename it from RKISP1_CIF_ISP_LSC_GRAD_SIZE() to RKISP1_CIF_ISP_LSC_SECT_GRAD() as the corresponding registers store the gradients for each sector, not a size. This doesn't cause any functional change as the two macros are defined identically (the size and gradient registers store fields in the same number of bits at the same positions). Signed-off-by: Laurent Pinchart Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Simplify LSC x/y size and grad register macros

2022-09-24T06:41:01Z

The LSC module x/y size and grad configuration is stored in a set of 4 indexed registers each. The rkisp1-regs.h header defines all those registers, but only the first one in each set is used, with manual calculation of addresses of subsequent registers. Simplifies this by merging all 4 register macros into one that takes the index as a parameter. No functional change intended. Signed-off-by: Laurent Pinchart Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Store LSC register values in u32 variables

2022-09-24T06:40:31Z

Use the u32 type instead of unsigned int to store register values in the LSC configuration code, to make the variables' size more explicit. No functional change intended. Signed-off-by: Laurent Pinchart Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Clean up LSC configuration code

2022-09-24T06:40:04Z

Clean up the LSC configuration code to improve its readability by shortening lines, using extra local variables and renaming long variables. No functional change intended. Signed-off-by: Laurent Pinchart Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Allow setting color space on resizer sink pad

2022-09-24T06:38:43Z

The resizer doesn't deal with color spaces, so it can accept any color space on its input, and propagates it unchanged to its output. When operating with a Bayer input format (in pass-through mode) further restrict the YCbCr encoding and quantization to Rec 601 and full range respectively, as for raw data the former ought to be ignored and the latter is always full range. Signed-off-by: Laurent Pinchart Reviewed-by: Paul Elder Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab

media: rkisp1: Initialize color space on resizer sink and source pads

2022-09-24T06:37:49Z

Initialize the four color space fields on the sink and source video pads of the resizer in the .init_cfg() operation. The resizer can't perform any color space conversion, so set the sink and source color spaces to the same defaults, which match the ISP source video pad default. Signed-off-by: Laurent Pinchart Reviewed-by: Paul Elder Reviewed-by: Dafna Hirschfeld Signed-off-by: Mauro Carvalho Chehab