linux-dev/drivers/net/can/spi, branch master

can: dev: fix skb drop check

2022-11-07T13:00:27Z

In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") the priv->ctrlmode element is read even on virtual CAN interfaces that do not create the struct can_priv at startup. This out-of-bounds read may lead to CAN frame drops for virtual CAN interfaces like vcan and vxcan. This patch mainly reverts the original commit and adds a new helper for CAN interface drivers that provide the required information in struct can_priv. Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") Reported-by: Dariusz Stojaczyk Cc: Vincent Mailhol Cc: Max Staudt Signed-off-by: Oliver Hartkopp Acked-by: Vincent Mailhol Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org # 6.0.x [mkl: patch pch_can, too] Signed-off-by: Marc Kleine-Budde

can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path

2022-10-25T07:13:14Z

In mcp251x_can_probe(), if mcp251x_gpio_setup() fails, it forgets to unregister the CAN device. Fix this by unregistering can device in mcp251x_can_probe(). Fixes: 2d52dabbef60 ("can: mcp251x: add GPIO support") Signed-off-by: Dongliang Mu Link: https://lore.kernel.org/all/20221024090256.717236-1-dzm91@hust.edu.cn [mkl: adjust label] Signed-off-by: Marc Kleine-Budde

can: mcp251x: Fix race condition on receive interrupt

2022-08-09T19:40:22Z

The mcp251x driver uses both receiving mailboxes of the CAN controller chips. For retrieving the CAN frames from the controller via SPI, it checks once per interrupt which mailboxes have been filled and will retrieve the messages accordingly. This introduces a race condition, as another CAN frame can enter mailbox 1 while mailbox 0 is emptied. If now another CAN frame enters mailbox 0 until the interrupt handler is called next, mailbox 0 is emptied before mailbox 1, leading to out-of-order CAN frames in the network device. This is fixed by checking the interrupt flags once again after freeing mailbox 0, to correctly also empty mailbox 1 before leaving the handler. For reproducing the bug I created the following setup: - Two CAN devices, one Raspberry Pi with MCP2515, the other can be any. - Setup CAN to 1 MHz - Spam bursts of 5 CAN-messages with increasing CAN-ids - Continue sending the bursts while sleeping a second between the bursts - Check on the RPi whether the received messages have increasing CAN-ids - Without this patch, every burst of messages will contain a flipped pair v3: https://lore.kernel.org/all/20220804075914.67569-1-sebastian.wuerl@ororatech.com v2: https://lore.kernel.org/all/20220804064803.63157-1-sebastian.wuerl@ororatech.com v1: https://lore.kernel.org/all/20220803153300.58732-1-sebastian.wuerl@ororatech.com Fixes: bf66f3736a94 ("can: mcp251x: Move to threaded interrupts instead of workqueues.") Signed-off-by: Sebastian Würl Link: https://lore.kernel.org/all/20220804081411.68567-1-sebastian.wuerl@ororatech.com [mkl: reduce scope of intf1, eflag1] Signed-off-by: Marc Kleine-Budde

can: mcp251xfd: advertise timestamping capabilities and add ioctl support

2022-07-28T09:44:30Z

Currently, userland has no methods to query which timestamping features are supported by the mcp251xfd driver (aside maybe of getting RX messages and observe whether or not hardware timestamps stay at zero). The canonical way for a network driver to advertise what kind of timestamping it supports is to implement ethtool_ops::get_ts_info(). Here, we use the CAN specific can_ethtool_op_get_ts_info_hwts() function to achieve this. In addition, the driver currently does not support the hardware timestamps ioctls. According to [1], SIOCSHWTSTAMP is "must" and SIOCGHWTSTAMP is "should". This patch fills up that gap by implementing net_device_ops::ndo_eth_ioctl() using the CAN specific function can_eth_ioctl_hwts(). [1] kernel doc Timestamping, section 3.1: "Hardware Timestamping Implementation: Device Drivers" Link: https://docs.kernel.org/networking/timestamping.html#hardware-timestamping-implementation-device-drivers Signed-off-by: Vincent Mailhol Link: https://lore.kernel.org/all/20220727101641.198847-10-mailhol.vincent@wanadoo.fr Signed-off-by: Marc Kleine-Budde

can: tree-wide: advertise software timestamping capabilities

2022-07-28T09:44:01Z

Currently, some CAN drivers support hardware timestamping, some do not. But userland has no method to query which features are supported (aside maybe of getting RX messages and observe whether or not hardware timestamps stay at zero). The canonical way for a network driver to advertised what kind of timestamping it supports is to implement ethtool_ops::get_ts_info(). This patch only targets the CAN drivers which *do not* support hardware timestamping. For each of those CAN drivers, implement the get_ts_info() using the generic ethtool_op_get_ts_info(). This way, userland can do: | $ ethtool --show-time-stamping canX to confirm the device timestamping capacities. N.B. the drivers which support hardware timestamping will be migrated in separate patches. Signed-off-by: Vincent Mailhol Link: https://lore.kernel.org/all/20220727101641.198847-6-mailhol.vincent@wanadoo.fr [mkl: mscan: add missing mscan_ethtool_ops] Signed-off-by: Marc Kleine-Budde

can: mcp251xfd: mcp251xfd_dump(): fix comment

2022-07-26T08:43:37Z

The driver uses only 1 TEF and 1 TX ring, but a variable number of RX rings. Fix comment accordingly. Fixes: e0ab3dd5f98f ("can: mcp251xfd: add dev coredump support") Link: https://lore.kernel.org/all/20220726084328.4042678-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2022-07-21T20:03:39Z

No conflicts. Signed-off-by: Jakub Kicinski

can: mcp251xfd: fix detection of mcp251863

2022-07-20T08:20:19Z

In commit c6f2a617a0a8 ("can: mcp251xfd: add support for mcp251863") support for the mcp251863 was added. However it was not taken into account that the auto detection of the chip model cannot distinguish between mcp2518fd and mcp251863 and would lead to a warning message if the firmware specifies a mcp251863. Fix auto detection: If a mcp2518fd compatible chip is found, keep the mcp251863 if specified by firmware, use mcp2518fd instead. Link: https://lore.kernel.org/all/20220706064835.1848864-1-mkl@pengutronix.de Fixes: c6f2a617a0a8 ("can: mcp251xfd: add support for mcp251863") Signed-off-by: Marc Kleine-Budde

can: add CAN_ERR_CNT flag to notify availability of error counter

2022-07-20T07:27:37Z

Add a dedicated flag in uapi/linux/can/error.h to notify the userland that fields data[6] and data[7] of the CAN error frame were respectively populated with the tx and rx error counters. For all driver tree-wide, set up this flags whenever needed. Link: https://lore.kernel.org/all/20220719143550.3681-12-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol Signed-off-by: Marc Kleine-Budde

can: hi311x: do not report txerr and rxerr during bus-off

2022-07-20T07:26:49Z

During bus off, the error count is greater than 255 and can not fit in a u8. Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver") Link: https://lore.kernel.org/all/20220719143550.3681-6-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol Signed-off-by: Marc Kleine-Budde