linux-dev/drivers/net/dsa/Kconfig, branch linus/master

net: dsa: restrict SMSC_LAN9303_I2C kconfig

2022-05-22T22:06:59Z

Since kconfig 'select' does not follow dependency chains, if symbol KSA selects KSB, then KSA should also depend on the same symbols that KSB depends on, in order to prevent Kconfig warnings and possible build errors. Change NET_DSA_SMSC_LAN9303_I2C and NET_DSA_SMSC_LAN9303_MDIO so that they are limited to VLAN_8021Q if the latter is enabled. This prevents the Kconfig warning: WARNING: unmet direct dependencies detected for NET_DSA_SMSC_LAN9303 Depends on [m]: NETDEVICES [=y] && NET_DSA [=y] && (VLAN_8021Q [=m] || VLAN_8021Q [=m]=n) Selected by [y]: - NET_DSA_SMSC_LAN9303_I2C [=y] && NETDEVICES [=y] && NET_DSA [=y] && I2C [=y] Fixes: 430065e26719 ("net: dsa: lan9303: add VLAN IDs to master device") Signed-off-by: Randy Dunlap Cc: Andrew Lunn Cc: Vivien Didelot Cc: Florian Fainelli Cc: Vladimir Oltean Cc: Juergen Borleis Cc: "David S. Miller" Cc: Eric Dumazet Cc: Jakub Kicinski Cc: Paolo Abeni Cc: Mans Rullgard Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2022-02-17T19:44:20Z

No conflicts. Signed-off-by: Jakub Kicinski

net: dsa: lan9303: add VLAN IDs to master device

2022-02-17T17:32:13Z

If the master device does VLAN filtering, the IDs used by the switch must be added for any frames to be received. Do this in the port_enable() function, and remove them in port_disable(). Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303") Signed-off-by: Mans Rullgard Reviewed-by: Florian Fainelli Reviewed-by: Vladimir Oltean Link: https://lore.kernel.org/r/20220216204818.28746-1-mans@mansr.com Signed-off-by: Jakub Kicinski

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2022-02-04T01:36:16Z

No conflicts. Signed-off-by: Jakub Kicinski

net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY

2022-02-01T05:18:17Z

Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to properly control MT7530 and MT7531 switch PHYs. A noticeable change is that the behaviour of switchport interfaces going up-down-up-down is no longer there. Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Arınç ÜNAL Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.com Signed-off-by: Jakub Kicinski

net: dsa: realtek-smi: move to subdirectory

2022-01-28T15:02:49Z

Signed-off-by: Luiz Angelo Daros de Luca Tested-by: Arınç ÜNAL Reviewed-by: Alvin Šipraga Reviewed-by: Linus Walleij Reviewed-by: Florian Fainelli Reviewed-by: Vladimir Oltean Signed-off-by: David S. Miller

net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC

2021-10-18T13:02:56Z

This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port 10/100/1000M switch controller. The driver has been developed based on a GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found in the OpenWrt source tree. Despite the name, the RTL8365MB-VC has an entirely different register layout to the already-supported RTL8366RB ASIC. Notwithstanding this, the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb subdriver. Like the 'rb, it establishes its own irqchip to handle cascaded PHY link status interrupts. The RTL8365MB-VC switch is capable of offloading a large number of features from the software, but this patch introduces only the most basic DSA driver functionality. The ports always function as standalone ports, with bridging handled in software. One more thing. Realtek's nomenclature for switches makes it hard to know exactly what other ASICs might be supported by this driver. The vendor driver goes by the name rtl8367c, but as far as I can tell, no chip actually exists under this name. As such, the subdriver is named rtl8365mb to emphasize the potentially limited support. But it is clear from the vendor sources that a number of other more advanced switches share a similar register layout, and further support should not be too hard to add given access to the relevant hardware. With this in mind, the subdriver has been written with as few assumptions about the particular chip as is reasonable. But the RTL8365MB-VC is the only hardware I have available, so some further work is surely needed. Co-developed-by: Michael Rasmussen Signed-off-by: Michael Rasmussen Signed-off-by: Alvin Šipraga Reviewed-by: Vladimir Oltean Reviewed-by: Linus Walleij Reviewed-by: Florian Fainelli Tested-by: Arınç ÜNAL Signed-off-by: David S. Miller

dsa: simplify Kconfig symbols and dependencies

2021-03-22T19:15:37Z

1. Remove CONFIG_HAVE_NET_DSA. CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers should have selected CONFIG_NET_DSA manually. Currently, all drivers has explicit 'depends on NET_DSA', so this is no more needed. 2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones. - dropped !S390 dependency which was introduced to be sure NET_DSA can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years ago and the PHY library itself doesn't depend on !S390 since commit 870a2b5e4fcd ("phylib: remove !S390 dependeny from Kconfig"); - INET dependency is kept to be sure we can select NET_SWITCHDEV; - NETDEVICES dependency is kept to be sure we can select PHYLINK. 3. DSA drivers menu now depends on NET_DSA. Instead on 'depends on NET_DSA' on every single driver, the entire menu now depends on it. This eliminates a lot of duplicated lines from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can be only m or n). This also has a nice side effect that there's no more empty menu on configurations without DSA. 4. Kbuild will now descend into 'drivers/net/dsa' only when CONFIG_NET_DSA is y or m. This is safe since no objects inside this folder can be built without DSA core, as well as when CONFIG_NET_DSA=m, no objects can be built-in. Signed-off-by: Alexander Lobakin Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: dsa: add Arrow SpeedChips XRS700x driver

2021-01-15T23:37:37Z

Add a driver with initial support for the Arrow SpeedChips XRS7000 series of gigabit Ethernet switch chips which are typically used in critical networking applications. The switches have up to three RGMII ports and one RMII port. Management to the switches can be performed over i2c or mdio. Support for advanced features such as PTP and HSR/PRP (IEC 62439-3 Clause 5 & 4) is not included in this patch and may be added at a later date. Signed-off-by: George McCollister Reviewed-by: Florian Fainelli Reviewed-by: Andrew Lunn Reviewed-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: dsa: Add DSA driver for Hirschmann Hellcreek switches

2020-11-05T22:04:49Z

Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are implementing features needed for Time Sensitive Networking (TSN) such as support for the Time Precision Protocol and various shapers like the Time Aware Shaper. This driver includes basic support for networking: * VLAN handling * FDB handling * Port statistics * STP * Phylink Signed-off-by: Kurt Kanzenbach Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: Jakub Kicinski