linux-dev/drivers/net/ethernet/amd/xgbe, branch master

amd-xgbe: add the bit rate quirk for Molex cables

2022-10-22T05:40:22Z

The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex passive cables have the rate ceiling 0x78 at offset 12. Add a quirk for Molex passive cables to extend the rate ceiling to 0x78. Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju Acked-by: Tom Lendacky Signed-off-by: Jakub Kicinski

amd-xgbe: fix the SFP compliance codes check for DAC cables

2022-10-22T05:40:22Z

The current XGBE code assumes that offset 6 of EEPROM SFP DAC (passive) cables is NULL. However, some cables (the 5 meter and 7 meter Molex passive cables) have non-zero data at offset 6. Fix the logic by moving the passive cable check above the active checks, so as not to be improperly identified as an active cable. This will fix the issue for any passive cable that advertises 1000Base-CX in offset 6. Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju Acked-by: Tom Lendacky Signed-off-by: Jakub Kicinski

amd-xgbe: enable PLL_CTL for fixed PHY modes only

2022-10-22T05:40:22Z

PLL control setting(RRC) is needed only in fixed PHY configuration to fix the peer-peer issues. Without the PLL control setting, the link up takes longer time in a fixed phy configuration. Driver implements SW RRC for Autoneg On configuration, hence PLL control setting (RRC) is not needed for AN On configuration, and can be skipped. Also, PLL re-initialization is not needed for PHY Power Off and RRC commands. Otherwise, they lead to mailbox errors. Added the changes accordingly. Fixes: daf182d360e5 ("net: amd-xgbe: Toggle PLL settings during rate change") Signed-off-by: Raju Rangoju Acked-by: Tom Lendacky Signed-off-by: Jakub Kicinski

amd-xgbe: use enums for mailbox cmd and sub_cmds

2022-10-22T05:40:21Z

Instead of using hardcoded values, use enumerations for mailbox command and sub commands. Signed-off-by: Raju Rangoju Acked-by: Tom Lendacky Signed-off-by: Jakub Kicinski

amd-xgbe: Yellow carp devices do not need rrc

2022-10-22T05:40:21Z

Link stability issues are noticed on Yellow carp platforms when Receiver Reset Cycle is issued. Since the CDR workaround is disabled on these platforms, the Receiver Reset Cycle is not needed. So, avoid issuing rrc on Yellow carp platforms. Fixes: dbb6c58b5a61 ("net: amd-xgbe: Add Support for Yellow Carp Ethernet device") Signed-off-by: Raju Rangoju Acked-by: Tom Lendacky Signed-off-by: Jakub Kicinski

net: drop the weight argument from netif_napi_add

2022-09-29T01:57:14Z

We tell driver developers to always pass NAPI_POLL_WEIGHT as the weight to netif_napi_add(). This may be confusing to newcomers, drop the weight argument, those who really need to tweak the weight can use netif_napi_add_weight(). Acked-by: Marc Kleine-Budde # for CAN Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org Signed-off-by: Jakub Kicinski

net: ethernet: move from strlcpy with unused retval to strscpy

2022-08-31T21:11:26Z

Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/ Signed-off-by: Wolfram Sang Reviewed-by: Petr Machata # For drivers/net/ethernet/mellanox/mlxsw Acked-by: Geoff Levand # For ps3_gelic_net and spider_net_ethtool Acked-by: Tom Lendacky # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c Acked-by: Marcin Wojtas # For drivers/net/ethernet/marvell/mvpp2 Reviewed-by: Leon Romanovsky # For drivers/net/ethernet/mellanox/mlx{4|5} Reviewed-by: Shay Agroskin # For drivers/net/ethernet/amazon/ena Acked-by: Krzysztof Hałasa # For IXP4xx Ethernet Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com Signed-off-by: Jakub Kicinski

amd-xgbe: fix clang -Wformat warnings

2022-07-12T02:53:51Z

When building with Clang we encounter the following warning: | drivers/net/ethernet/amd/xgbe/xgbe-dcb.c:234:42: error: format specifies | type 'unsigned char' but the argument has type '__u16' (aka 'unsigned | short') [-Werror,-Wformat] pfc->pfc_cap, pfc->pfc_en, pfc->mbc, | pfc->delay); pfc->pfc_cap , pfc->pfc_cn, pfc->mbc are all of type `u8` while pfc->delay is of type `u16`. The correct format specifiers `%hh[u|x]` were used for the first three but not for pfc->delay, which is causing the warning above. Variadic functions (printf-like) undergo default argument promotion. Documentation/core-api/printk-formats.rst specifically recommends using the promoted-to-type's format flag. In this case `%d` (or `%x` to maintain hex representation) should be used since both u8's and u16's are fully representable by an int. Moreover, C11 6.3.1.1 states: (https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf) `If an int can represent all values of the original type ..., the value is converted to an int; otherwise, it is converted to an unsigned int. These are called the integer promotions.` Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Justin Stitt Reviewed-by: Nick Desaulniers Tested-by: Nick Desaulniers Link: https://lore.kernel.org/r/20220708232653.556488-1-justinstitt@google.com Signed-off-by: Jakub Kicinski

net: add skb_[inner_]tcp_all_headers helpers

2022-07-02T15:22:25Z

Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)" to compute headers length for a TCP packet, but others use more convoluted (but equivalent) ways. Add skb_tcp_all_headers() and skb_inner_tcp_all_headers() helpers to harmonize this a bit. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller

amd/xgbe: fix repeated words in comments

2022-06-28T05:06:18Z

Delete the redundant word 'use'. Signed-off-by: Jilin Yuan Link: https://lore.kernel.org/r/20220625070633.64982-1-yuanjilin@cdjrlc.com Signed-off-by: Jakub Kicinski