linux-dev/drivers/net/ethernet/cortina, branch master

net: drop the weight argument from netif_napi_add

2022-09-29T01:57:14Z

We tell driver developers to always pass NAPI_POLL_WEIGHT as the weight to netif_napi_add(). This may be confusing to newcomers, drop the weight argument, those who really need to tweak the weight can use netif_napi_add_weight(). Acked-by: Marc Kleine-Budde # for CAN Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org Signed-off-by: Jakub Kicinski

net: Use u64_stats_fetch_begin_irq() for stats fetch.

2022-08-29T12:02:27Z

On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the reader is in preemptible context and the writer side (u64_stats_update_begin*()) runs in an interrupt context (IRQ or softirq) then the writer can update the stats during the read operation. This update remains undetected. Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP are not interrupted by a writer. 32bit-SMP remains unaffected by this change. Cc: "David S. Miller" Cc: Catherine Sullivan Cc: David Awogbemila Cc: Dimitris Michailidis Cc: Eric Dumazet Cc: Hans Ulli Kroll Cc: Jakub Kicinski Cc: Jeroen de Borst Cc: Johannes Berg Cc: Linus Walleij Cc: Paolo Abeni Cc: Simon Horman Cc: linux-arm-kernel@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: oss-drivers@corigine.com Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior Reviewed-by: Simon Horman Signed-off-by: David S. Miller

eth: remove copies of the NAPI_POLL_WEIGHT define

2022-04-29T10:56:41Z

Defining local versions of NAPI_POLL_WEIGHT with the same values in the drivers just makes refactoring harder. Drop the special defines in a bunch of drivers where the removal is relatively simple so grouping into one patch does not impact reviewability. Signed-off-by: Jakub Kicinski Reviewed-by: Paul Durrant Signed-off-by: David S. Miller

net: ethernet: cortina: permit to set mac address in DT

2022-01-27T02:43:50Z

Add ability of setting mac address in DT for cortina ethernet driver. Signed-off-by: Corentin Labbe Reviewed-by: Linus Walleij Link: https://lore.kernel.org/r/20220125210811.54350-1-clabbe@baylibre.com Signed-off-by: Jakub Kicinski

net: gemini: allow any RGMII interface mode

2022-01-05T18:31:22Z

The four RGMII interface modes take care of the required RGMII delay configuration at the PHY and should not be limited by the network MAC driver. Sadly, gemini was only permitting RGMII mode with no delays, which would require the required delay to be inserted via PCB tracking or by the MAC. However, there are designs that require the PHY to add the delay, which is impossible without Gemini permitting the other three PHY interface modes. Fix the driver to allow these. Signed-off-by: Russell King (Oracle) Reviewed-by: Linus Walleij Tested-by: Corentin Labbe Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

ethtool: extend ringparam setting/getting API with rx_buf_len

2021-11-22T12:31:49Z

Add two new parameters kernel_ringparam and extack for .get_ringparam and .set_ringparam to extend more ring params through netlink. Signed-off-by: Hao Chen Signed-off-by: Guangbin Huang Signed-off-by: David S. Miller

ethernet: make use of eth_hw_addr_random() where appropriate

2021-10-14T16:22:15Z

Number of drivers use eth_random_addr(netdev->dev_addr) thus writing to netdev->dev_addr directly, and not setting the address type. Switch them to eth_hw_addr_random(). @@ expression netdev; @@ - eth_random_addr(netdev->dev_addr); + eth_hw_addr_random(netdev); Reviewed-by: Linus Walleij Signed-off-by: Jakub Kicinski

ethernet: use eth_hw_addr_set() - casts

2021-10-02T13:18:26Z

eth_hw_addr_set() takes a u8 pointer, like other etherdevice helpers. Convert the few drivers which require casts because they memcpy from "endian marked" types. Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller

ethernet: use eth_hw_addr_set()

2021-10-02T13:18:25Z

Convert all Ethernet drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, ETH_ALEN) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller

ethtool: extend coalesce setting uAPI with CQE mode

2021-08-24T14:38:29Z

In order to support more coalesce parameters through netlink, add two new parameter kernel_coal and extack for .set_coalesce and .get_coalesce, then some extra info can return to user with the netlink API. Signed-off-by: Yufeng Mo Signed-off-by: Huazhong Tan Signed-off-by: Jakub Kicinski