linux-dev/drivers/net/ethernet/synopsys, branch linus/master

net: allow gso_max_size to exceed 65536

2022-05-16T09:18:55Z

The code for gso_max_size was added originally to allow for debugging and workaround of buggy devices that couldn't support TSO with blocks 64K in size. The original reason for limiting it to 64K was because that was the existing limits of IPv4 and non-jumbogram IPv6 length fields. With the addition of Big TCP we can remove this limit and allow the value to potentially go up to UINT_MAX and instead be limited by the tso_max_size value. So in order to support this we need to go through and clean up the remaining users of the gso_max_size value so that the values will cap at 64K for non-TCPv6 flows. In addition we can clean up the GSO_MAX_SIZE value so that 64K becomes GSO_LEGACY_MAX_SIZE and UINT_MAX will now be the upper limit for GSO_MAX_SIZE. v6: (edumazet) fixed a compile error if CONFIG_IPV6=n, in a new sk_trim_gso_size() helper. netif_set_tso_max_size() caps the requested TSO size with GSO_MAX_SIZE. Signed-off-by: Alexander Duyck Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller

ethernet: constify references to netdev->dev_addr in drivers

2021-10-14T16:22:11Z

This big patch sprinkles const on local variables and function arguments which may refer to netdev->dev_addr. Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Some of the changes here are not strictly required - const is sometimes cast off but pointer is not used for writing. It seems like it's still better to add the const in case the code changes later or relevant -W flags get enabled for the build. No functional changes. Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org Signed-off-by: Jakub Kicinski

ethernet: use eth_hw_addr_set() for dev->addr_len cases

2021-10-05T12:16:48Z

Convert all Ethernet drivers from memcpy(... dev->addr_len) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, dev->addr_len) + eth_hw_addr_set(dev, np) In theory addr_len may not be ETH_ALEN, but we don't expect non-Ethernet devices to live under this directory, and only the following cases of setting addr_len exist: - cxgb4 for mgmt device, and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge. Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller

ethtool: extend coalesce setting uAPI with CQE mode

2021-08-24T14:38:29Z

In order to support more coalesce parameters through netlink, add two new parameter kernel_coal and extack for .set_coalesce and .get_coalesce, then some extra info can return to user with the netlink API. Signed-off-by: Yufeng Mo Signed-off-by: Huazhong Tan Signed-off-by: Jakub Kicinski

dev_ioctl: split out ndo_eth_ioctl

2021-07-27T19:11:45Z

Most users of ndo_do_ioctl are ethernet drivers that implement the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP. Separate these from the few drivers that use ndo_do_ioctl to implement SIOCBOND, SIOCBR and SIOCWANDEV commands. This is a purely cosmetic change intended to help readers find their way through the implementation. Cc: Doug Ledford Cc: Jason Gunthorpe Cc: Jay Vosburgh Cc: Veaceslav Falico Cc: Andy Gospodarek Cc: Andrew Lunn Cc: Vivien Didelot Cc: Florian Fainelli Cc: Vladimir Oltean Cc: Leon Romanovsky Cc: linux-rdma@vger.kernel.org Signed-off-by: Arnd Bergmann Acked-by: Jason Gunthorpe Signed-off-by: David S. Miller

net: dwc-xlgmac: Fix spelling mistake in function name

2021-02-06T19:37:01Z

There is a spelling mistake in the function name alloc_channles_and_rings. Fix this by renaming it to alloc_channels_and_rings. Signed-off-by: Colin Ian King Link: https://lore.kernel.org/r/20210204094944.51460-1-colin.king@canonical.com Signed-off-by: Jakub Kicinski

drivers/net/ethernet: clean up unused assignments

2020-09-25T23:29:00Z

As part of the W=1 compliation series, these lines all created warnings about unused variables that were assigned a value. Most of them are from register reads, but some are just picking up a return value from a function and never doing anything with it. Fixed warnings: .../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable] .../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable] .../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable] .../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable] .../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable] .../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs ' .../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable] .../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable] .../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] .../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable] .../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable] .../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable] .../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable] .../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable] .../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable] .../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable] The register reads should be OK, because the current implementation of readl and friends will always execute even without an lvalue. When it makes sense, just remove the lvalue assignment and the local. Other times, just remove the offending code, and occasionally, just mark the variable as maybe unused since it could be used in an ifdef or debug scenario. Only compile tested with W=1. Signed-off-by: Jesse Brandeburg Acked-by: Edward Cree Signed-off-by: David S. Miller

net: dwc-xlgmac: fix xlgmac_xmit()'s return type

2020-06-29T03:52:53Z

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, but the implementation in this driver returns an 'int'. Fix this by returning 'netdev_tx_t' in this driver too. Signed-off-by: Luc Van Oostenryck Signed-off-by: David S. Miller

treewide: replace '---help---' in Kconfig files with 'help'

2020-06-13T16:57:21Z

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada

net: dwc-xlgmac: let core reject the unsupported coalescing parameters

2020-03-18T03:56:57Z

Set ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters. This driver already correctly rejected all unsupported parameters. While at it remove unnecessary zeroing on get. No functional changes. Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller