linux-dev/drivers/net/ethernet/ti/Makefile, branch master

net: ti: am65-cpsw-nuss: Add switchdev support

2021-02-12T01:52:13Z

J721e, J7200 and AM64 have multi port switches which can work in multi mac mode and in switch mode. Add support for configuring this HW in switch mode using devlink and switchdev notifiers. Support is similar to existing CPSW switchdev implementation of TI's 32 bit platform like AM33/AM43/AM57. To enable switch mode: devlink dev param set platform/8000000.ethernet name switch_mode value true cmode runtime All configuration is implemented via switchdev API and notifiers. Supported: - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_STP_STATE - SWITCHDEV_OBJ_ID_PORT_VLAN - SWITCHDEV_OBJ_ID_PORT_MDB - SWITCHDEV_OBJ_ID_HOST_MDB Hence AM65 CPSW switchdev driver supports: - FDB offloading - MDB offloading - VLAN filtering and offloading - STP Signed-off-by: Vignesh Raghavendra Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2020-05-15T20:48:59Z

Move the bpf verifier trace check into the new switch statement in HEAD. Resolve the overlapping changes in hinic, where bug fixes overlap the addition of VF support. Signed-off-by: David S. Miller

ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

2020-05-15T00:33:30Z

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018) configuration. EST allows express queue traffic to be scheduled (placed) on the wire at specific repeatable time intervals. In Linux kernel, EST configuration is done through tc command and the taprio scheduler in the net core implements a software only scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration, user indicate "flag 2" in the command which is then parsed by taprio scheduler in net core and indicate that the command is to be offloaded to h/w. taprio then offloads the command to the driver by calling ndo_setup_tc() ndo ops. This patch implements ndo_setup_tc() to offload EST configuration to CPSW h/w. Currently driver supports only SetGateStates operation. EST operates on a repeating time interval generated by the CPTS EST function generator. Each Ethernet port has a global EST fetch RAM that can be configured as 2 buffers, each of 64 locations or one large buffer of 128 locations. In 2 buffer configuration, a ping pong mechanism is used to hold the active schedule (oper) in one buffer and new (admin) command in the other. Each 22-bit fetch command consists of a 14-bit fetch count (14 MSB’s) and an 8-bit priority fetch allow (8 LSB’s) that will be applied for the fetch count time in wireside clocks. Driver process each of the sched-entry in the offload command and update the fetch RAM. Driver configures duration in sched-entry into the fetch count and Gate mask into the priority fetch bits of the RAM. Then configures the CPTS EST function generator to activate the schedule. Currently driver supports only 2 buffer configuration which means driver supports a max cycle time of ~8 msec. CPSW supports a configurable number of priority queues (up to 8) and needs to be switched to this mode from the default round robin mode before EST can be offloaded. User configures these through ethtool commands (-L for changing number of queues and --set-priv-flags to disable round robin mode). Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag is set. The flag is common for all ports, and so can't be just overridden by taprio configuration w/o user involvement. Command fails if pf_p0_rx_ptype_rrobin is already set in the driver. Scheds (commands) configuration depends on interface speed so driver translates the duration to the fetch count based on link speed. Each schedule can be constructed with several command entries in fetch RAM depending on interval. For example if each sched has timer interval < ~130us on 1000 Mb link then each sched consumes one command and have 1:1 mapping. When Ethernet link goes down, driver purge the configuration if link is down for more than 1 second. The patch allows to update the timer and scheds memory only if it's really needed, and skip cases required the user to stop timer by configuring only shceds memory. Signed-off-by: Ivan Khoronzhuk Signed-off-by: Murali Karicheri Signed-off-by: David S. Miller

net: ethernet: ti: Remove TI_CPTS_MOD workaround

2020-05-12T19:33:27Z

My recent commit b6d49cab44b5 ("net: Make PTP-specific drivers depend on PTP_1588_CLOCK") exposes a missing dependency in defconfigs that select TI_CPTS without selecting PTP_1588_CLOCK, leading to linker errors of the form: drivers/net/ethernet/ti/cpsw.o: in function `cpsw_ndo_stop': cpsw.c:(.text+0x680): undefined reference to `cpts_unregister' ... That's because TI_CPTS_MOD (which is the symbol gating the _compilation_ of cpts.c) now depends on PTP_1588_CLOCK, and so is not enabled in these configurations, but TI_CPTS (which is the symbol gating _calls_ to the cpts functions) _is_ enabled. So we end up compiling calls to functions that don't exist, resulting in the linker errors. This patch fixes build errors and restores previous behavior by: - ensure PTP_1588_CLOCK=y in TI specific configs and CPTS will be built - remove TI_CPTS_MOD and, instead, add dependencies from CPTS in TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV as below: config TI_CPSW_SWITCHDEV ... depends on TI_CPTS || !TI_CPTS which will ensure proper dependencies PTP_1588_CLOCK -> TI_CPTS -> TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV and build type selection. Note. For NFS boot + CPTS all of above configs have to be built-in. Cc: Arnd Bergmann Cc: Dan Murphy Cc: Tony Lindgren Fixes: b6d49cab44b5 ("net: Make PTP-specific drivers depend on PTP_1588_CLOCK") Reported-by: kbuild test robot Signed-off-by: Clay McClure [grygorii.strashko@ti.com: rewording, add deps cpsw/netcp from cpts, drop IS_REACHABLE] Signed-off-by: Grygorii Strashko Reviewed-by: Arnd Bergmann Tested-by: Tony Lindgren Signed-off-by: David S. Miller

net: ethernet: ti: introduce am654 common platform time sync driver

2020-05-04T19:02:02Z

The CPTS module is used to facilitate host control of time sync operations. Main features of CPTS module are: - selection of multiple external clock sources - control of time sync events via interrupt or polling - 64-bit timestamp mode in ns with HW PPM and nudge adjustment. - hardware timestamp ext. inputs (HWx_TS_PUSH) - timestamp Generator function outputs (TS_GENFx) Depending on integration it enables compliance with the IEEE 1588-2008 standard for a precision clock synchronization protocol, Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn) and PCIe Subsystem Precision Time Measurement (PTM). Introduced driver provides Linux PTP hardware clock for each CPTS device and network packets timestamping where applicable. CPTS PTP hardware clock supports following operations: - Set time - Get time - Shift the clock by a given offset atomically - Adjust clock frequency - Time stamp external events - Periodic output signals Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

2020-03-27T03:01:14Z

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has two ports - One Ethernet port (port 1) with selectable RGMII and RMII interfaces and an internal Communications Port Programming Interface (CPPI) port (Host port 0) and with ALE in between. It also contains - Management Data Input/Output (MDIO) interface for physical layer device (PHY) management; - Updated Address Lookup Engine (ALE) module; - (TBD) New version of Common platform time sync (CPTS) module. On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU domain named MCU_CPSW0. Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX channels and one RX channels operating by TI am654 NAVSS Unified DMA Peripheral Root Complex (UDMA-P) controller. Introduced driver provides standard Linux net_device to user space and supports: - ifconfig up/down - MAC address configuration - ethtool operation: --driver --change --register-dump --negotiate phy --statistics --set-eee phy --show-ring --show-channels --set-channels - net_device ioctl mii-control - promisc mode - rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets. The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills csum information for each packet in psdata[2] word: - BIT(16) CHECKSUM_ERROR - indicates csum error - BIT(17) FRAGMENT - indicates fragmented packet - BIT(18) TCP_UDP_N - Indicates TCP packet was detected - BIT(19) IPV6_VALID, BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet - BIT(15, 0) CHECKSUM_ADD - This is the value that was summed during the checksum computation. This value is FFFFh for non fragmented IPV4/6 UDP/TCP packets with no checksum error. RX csum offload can be disabled: ethtool -K rx-checksum on|off - tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only). TX csum HW offload can be enabled/disabled: ethtool -K tx-checksum-ip-generic on|off - multiq and switch between round robin/prio modes for cppi tx queues by using Netdev private flag "p0-rx-ptype-rrobin" to switch between Round Robin and Fixed priority modes: # ethtool --show-priv-flags eth0 Private flags for eth0: p0-rx-ptype-rrobin: on # ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off Number of TX DMA channels can be changed using "ethtool -L eth0 tx ". - GRO support: the napi_gro_receive() and napi_complete_done() are used. Signed-off-by: Grygorii Strashko Tested-by: Murali Karicheri Tested-by: Peter Ujfalusi Signed-off-by: David S. Miller

net: ethernet: ti: build cpsw-common for switchdev

2019-12-14T20:51:00Z

Without the common part of the driver, the new file fails to link: drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_probe': cpsw_new.c:(.text+0x312c): undefined reference to `ti_cm_get_macid' Use the same Makefile hack as before, and build cpsw-common.o for any driver that needs it. Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by: Arnd Bergmann Reviewed-by: Grygorii Strashko Signed-off-by: Jakub Kicinski

net: ethernet: ti: introduce cpsw switchdev based driver part 2 - switch

2019-11-20T19:25:24Z

CPSW switchdev based driver which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. The Switch mode can be enabled by configuring devlink driver parameter "switch_mode" to 1: devlink dev param set platform/48484000.switch \ name switch_mode value 1 cmode runtime This can be done regardless of the state of Port's netdevs - UP/DOWN, but Port's netdev devices have to be UP before joining the bridge to avoid overwriting of bridge configuration as CPSW switch driver completely reloads its configuration when first Port changes its state to UP. When the both interfaces joined the bridge - CPSW switch driver will start marking packets with offload_fwd_mark flag unless "ale_bypass=0". All configuration is implemented via switchdev API and notifiers. Supported: - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD - SWITCHDEV_ATTR_ID_PORT_STP_STATE - SWITCHDEV_OBJ_ID_PORT_VLAN - SWITCHDEV_OBJ_ID_PORT_MDB - SWITCHDEV_OBJ_ID_HOST_MDB Hence CPSW switchdev driver supports: - FDB offloading - MDB offloading - VLAN filtering and offloading - STP Signed-off-by: Ilias Apalodimas Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller

net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac

2019-11-20T19:25:23Z

Part 1: Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. Main differences from legacy CPSW driver are: - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering, which is provides significant benefits when ports are joined to the same bridge, but without enabling "switch" mode, or to different bridges. - learning disabled on ports as it make not too much sense for segregated ports - no forwarding in HW. - enabled basic support for devlink. devlink dev show platform/48484000.switch devlink dev param show platform/48484000.switch: name ale_bypass type driver-specific values: cmode runtime value false - "ale_bypass" devlink driver parameter allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes. - updated DT bindings. Signed-off-by: Ilias Apalodimas Signed-off-by: Murali Karicheri Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller

net: ethernet: ti: netcp_ethss: fix build

2019-05-13T16:56:05Z

Fix reported build fail: ERROR: "cpsw_ale_flush_multicast" [drivers/net/ethernet/ti/keystone_netcp_ethss.ko] undefined! ERROR: "cpsw_ale_create" [drivers/net/ethernet/ti/keystone_netcp_ethss.ko] undefined! ERROR: "cpsw_ale_add_vlan" [drivers/net/ethernet/ti/keystone_netcp_ethss.ko] undefined! Fixes: 16f54164828b ("net: ethernet: ti: cpsw: drop CONFIG_TI_CPSW_ALE config option") Reported-by: kbuild test robot Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller