linux-dev/drivers/net/usb, branch linus/master

net: usb: ax88179_178a needs FLAG_SEND_ZLP

2022-06-15T08:32:12Z

The extra byte inserted by usbnet.c when (length % dev->maxpacket == 0) is causing problems to device. This patch sets FLAG_SEND_ZLP to avoid this. Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet Problems observed: ====================================================================== 1) Using ssh/sshfs. The remote sshd daemon can abort with the message: "message authentication code incorrect" This happens because the tcp message sent is corrupted during the USB "Bulk out". The device calculate the tcp checksum and send a valid tcp message to the remote sshd. Then the encryption detects the error and aborts. 2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out 3) Stop normal work without any log message. The "Bulk in" continue receiving packets normally. The host sends "Bulk out" and the device responds with -ECONNRESET. (The netusb.c code tx_complete ignore -ECONNRESET) Under normal conditions these errors take days to happen and in intense usage take hours. A test with ping gives packet loss, showing that something is wrong: ping -4 -s 462 {destination} # 462 = 512 - 42 - 8 Not all packets fail. My guess is that the device tries to find another packet starting at the extra byte and will fail or not depending on the next bytes (old buffer content). ====================================================================== Signed-off-by: Jose Alonso Signed-off-by: David S. Miller

Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2022-06-03T18:17:49Z

Pull USB / Thunderbolt updates from Greg KH: "Here is the "big" set of USB and Thunderbolt driver changes for 5.18-rc1. For the most part it's been a quiet development cycle for the USB core, but there are the usual "hot spots" of development activity. Included in here are: - Thunderbolt driver updates: - fixes for devices without displayport adapters - lane bonding support and improvements - other minor changes based on device testing - dwc3 gadget driver changes. It seems this driver will never be finished given that the IP core is showing up in zillions of new devices and each implementation decides to do something different with it... - uvc gadget driver updates as more devices start to use and rely on this hardware as well - usb_maxpacket() api changes to remove an unneeded and unused parameter. - usb-serial driver device id updates and small cleanups - typec cleanups and fixes based on device testing - device tree updates for usb properties - lots of other small fixes and driver updates. All of these have been in linux-next for weeks with no reported problems" * tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits) USB: new quirk for Dell Gen 2 devices usb: dwc3: core: Add error log when core soft reset failed usb: dwc3: gadget: Move null pinter check to proper place usb: hub: Simplify error and success path in port_over_current_notify usb: cdns3: allocate TX FIFO size according to composite EP number usb: dwc3: Fix ep0 handling when getting reset while doing control transfer usb: Probe EHCI, OHCI controllers asynchronously usb: isp1760: Fix out-of-bounds array access xhci: Don't defer primary roothub registration if there is only one roothub USB: serial: option: add Quectel BG95 modem USB: serial: pl2303: fix type detection for odd device xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI xhci: Remove quirk for over 10 year old evaluation hardware xhci: prevent U2 link power state if Intel tier policy prevented U1 xhci: use generic command timer for stop endpoint commands. usb: host: xhci-plat: omit shared hcd if either root hub has no ports usb: host: xhci-plat: prepare operation w/o shared hcd usb: host: xhci-plat: create shared hcd after having added main hcd xhci: prepare for operation w/o shared hcd xhci: factor out parts of xhci_gen_setup() ...

net: usb: qmi_wwan: Add support for Cinterion MV31 with new baseline

2022-06-02T01:09:34Z

Adding support for Cinterion device MV31 with Qualcomm new baseline. Use different PIDs to separate it from previous base line products. All interfaces settings keep same as previous. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=00b9 Rev=04.14 S: Manufacturer=Cinterion S: Product=Cinterion PID 0x00B9 USB Mobile Broadband S: SerialNumber=90418e79 C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option Signed-off-by: Slark Xiao Acked-by: Bjørn Mork Link: https://lore.kernel.org/r/20220601040531.6016-1-slark_xiao@163.com Signed-off-by: Jakub Kicinski

net: usb: qmi_wwan: add Telit 0x1250 composition

2022-05-27T11:12:40Z

Add support for Telit LN910Cx 0x1250 composition 0x1250: rmnet, tty, tty, tty, tty Signed-off-by: Carlo Lobrano Acked-by: Bjørn Mork Signed-off-by: David S. Miller

net: usb: r8152: Add in new Devices that are supported for Mac-Passthru

2022-05-20T00:21:24Z

Lenovo Thunderbolt 4 Dock, and other Lenovo USB Docks are using the original Realtek USB ethernet Vendor and Product IDs If the Network device is Realtek verify that it is on a Lenovo USB hub before enabling the passthru feature This also adds in the device IDs for the Lenovo USB Dongle and one other USB-C dock V2 fix formating of code V3 remove Generic define for Device ID 0x8153 and change it to use value V4 rearrange defines and case statement to put them in better order v5 create helper function to do the testing work as suggested Signed-off-by: David Ober Link: https://lore.kernel.org/r/20220517180539.25839-1-dober6023@gmail.com Signed-off-by: Jakub Kicinski

usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling

2022-05-13T10:35:46Z

Link status of SMSC LAN95xx chips is polled once per second, even though they're capable of signaling PHY interrupts through the MAC layer. Forward those interrupts to the PHY driver to avoid polling. Benefits are reduced bus traffic, reduced CPU overhead and quicker interface bringup. Polling was introduced in 2016 by commit d69d16949346 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation"). Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt, hence couldn't detect link-up events when auto-negotiation was disabled. The proper solution would have been to enable the ENERGYON interrupt instead of polling. Since then, PHY handling was moved from the LAN95xx driver to the SMSC PHY driver with commit 05b35e7eb9a1 ("smsc95xx: add phylib support"). That PHY driver is capable of link detection with auto-negotiation disabled because it enables the ENERGYON interrupt. Note that signaling interrupts through the MAC layer not only works with the integrated PHY, but also with an external PHY, provided its interrupt pin is attached to LAN95xx's nPHY_INT pin. In the unlikely event that the interrupt pin of an external PHY is attached to a GPIO of the SoC (or not connected at all), the driver can be amended to retrieve the irq from the PHY's of_node. To forward PHY interrupts to phylib, it is not sufficient to call phy_mac_interrupt(). Instead, the PHY's interrupt handler needs to run so that PHY interrupts are cleared. That's because according to page 119 of the LAN950x datasheet, "The source of this interrupt is a level. The interrupt persists until it is cleared in the PHY." https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf Therefore, create an IRQ domain with a single IRQ for the PHY. In the future, the IRQ domain may be extended to support the 11 GPIOs on the LAN95xx. Normally the PHY interrupt should be masked until the PHY driver has cleared it. However masking requires a (sleeping) USB transaction and interrupts are received in (non-sleepable) softirq context. I decided not to mask the interrupt at all (by using the dummy_irq_chip's noop ->irq_mask() callback): The USB interrupt endpoint is polled in 1 msec intervals and normally that's sufficient to wake the PHY driver's IRQ thread and have it clear the interrupt. If it does take longer, worst thing that can happen is the IRQ thread is woken again. No big deal. Because PHY interrupts are now perpetually enabled, there's no need to selectively enable them on suspend. So remove all invocations of smsc95xx_enable_phy_wakeup_interrupts(). In smsc95xx_resume(), move the call of phy_init_hw() before usbnet_resume() (which restarts the status URB) to ensure that the PHY is fully initialized when an interrupt is handled. Tested-by: Oleksij Rempel # LAN9514/9512/9500 Tested-by: Ferry Toth # LAN9514 Signed-off-by: Lukas Wunner Reviewed-by: Andrew Lunn # from a PHY perspective Cc: Andre Edich Signed-off-by: David S. Miller

usbnet: smsc95xx: Avoid link settings race on interrupt reception

2022-05-13T10:35:46Z

When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the MAC full duplex mode and PHY flow control registers based on cached data in struct phy_device: smsc95xx_status() # raises EVENT_LINK_RESET usbnet_deferred_kevent() smsc95xx_link_reset() # uses cached data in phydev Simultaneously, phylib polls link status once per second and updates that cached data: phy_state_machine() phy_check_link_status() phy_read_status() lan87xx_read_status() genphy_read_status() # updates cached data in phydev If smsc95xx_link_reset() wins the race against genphy_read_status(), the registers may be updated based on stale data. E.g. if the link was previously down, phydev->duplex is set to DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even though genphy_read_status() may update it to DUPLEX_FULL afterwards. PHY interrupts are currently only enabled on suspend to trigger wakeup, so the impact of the race is limited, but we're about to enable them perpetually. Avoid the race by delaying execution of smsc95xx_link_reset() until phy_state_machine() has done its job and calls back via smsc95xx_handle_link_change(). Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib picks up link status changes through polling. So drop the declaration of a ->link_reset() callback. Note that the semicolon on a line by itself added in smsc95xx_status() is a placeholder for a function call which will be added in a subsequent commit. That function call will actually handle the INT_ENP_PHY_INT_ interrupt. Tested-by: Oleksij Rempel # LAN9514/9512/9500 Tested-by: Ferry Toth # LAN9514 Signed-off-by: Lukas Wunner Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

usbnet: smsc95xx: Don't reset PHY behind PHY driver's back

2022-05-13T10:35:46Z

smsc95xx_reset() resets the PHY behind the PHY driver's back, which seems like a bad idea generally. Remove that portion of the function. We're about to use PHY interrupts instead of polling to detect link changes on SMSC LAN95xx chips. Because smsc95xx_reset() is called from usbnet_open(), PHY interrupt settings are lost whenever the net_device is brought up. There are two other callers of smsc95xx_reset(), namely smsc95xx_bind() and smsc95xx_reset_resume(), and both may indeed benefit from a PHY reset. However they already perform one through their calls to phy_connect_direct() and phy_init_hw(). Tested-by: Oleksij Rempel # LAN9514/9512/9500 Tested-by: Ferry Toth # LAN9514 Signed-off-by: Lukas Wunner Cc: Martyn Welch Cc: Gabriel Hojda Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

usbnet: smsc95xx: Don't clear read-only PHY interrupt

2022-05-13T10:35:46Z

Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver attempts to clear the signaled interrupts by writing "all ones" to the Interrupt Status Register. However the driver only ever enables a single type of interrupt, namely the PHY Interrupt. And according to page 119 of the LAN950x datasheet, its bit in the Interrupt Status Register is read-only. There's no other way to clear it than in a separate PHY register: https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf Consequently, writing "all ones" to the Interrupt Status Register is pointless and can be dropped. Tested-by: Oleksij Rempel # LAN9514/9512/9500 Tested-by: Ferry Toth # LAN9514 Signed-off-by: Lukas Wunner Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

usbnet: Run unregister_netdev() before unbind() again

2022-05-13T10:35:46Z

Commit 2c9d6c2b871d ("usbnet: run unbind() before unregister_netdev()") sought to fix a use-after-free on disconnect of USB Ethernet adapters. It turns out that a different fix is necessary to address the issue: https://lore.kernel.org/netdev/18b3541e5372bc9b9fc733d422f4e698c089077c.1650177997.git.lukas@wunner.de/ So the commit was not necessary. The commit made binding and unbinding of USB Ethernet asymmetrical: Before, usbnet_probe() first invoked the ->bind() callback and then register_netdev(). usbnet_disconnect() mirrored that by first invoking unregister_netdev() and then ->unbind(). Since the commit, the order in usbnet_disconnect() is reversed and no longer mirrors usbnet_probe(). One consequence is that a PHY disconnected (and stopped) in ->unbind() is afterwards stopped once more by unregister_netdev() as it closes the netdev before unregistering. That necessitates a contortion in ->stop() because the PHY may only be stopped if it hasn't already been disconnected. Reverting the commit allows making the call to phy_stop() unconditional in ->stop(). Tested-by: Oleksij Rempel # LAN9514/9512/9500 Tested-by: Ferry Toth # LAN9514 Signed-off-by: Lukas Wunner Acked-by: Oliver Neukum Cc: Martyn Welch Cc: Andrew Lunn Signed-off-by: David S. Miller