linux-dev/drivers/nvme/host/Makefile, branch master

nvme: don't always build constants.o

2022-08-02T23:22:48Z

The entire content of constants.c if guarded by an ifdef, so switch to just building the file conditionally instead. Signed-off-by: Christoph Hellwig Reviewed-by: Keith Busch Reviewed-by: Chaitanya Kulkarni Reviewed-by: Sagi Grimberg Signed-off-by: Jens Axboe

nvme: implement In-Band authentication

2022-08-02T23:14:49Z

Implement NVMe-oF In-Band authentication according to NVMe TPAR 8006. This patch adds two new fabric options 'dhchap_secret' to specify the pre-shared key (in ASCII respresentation according to NVMe 2.0 section 8.13.5.8 'Secret representation') and 'dhchap_ctrl_secret' to specify the pre-shared controller key for bi-directional authentication of both the host and the controller. Re-authentication can be triggered by writing the PSK into the new controller sysfs attribute 'dhchap_secret' or 'dhchap_ctrl_secret'. Signed-off-by: Hannes Reinecke Reviewed-by: Sagi Grimberg Signed-off-by: Christoph Hellwig [axboe: fold in clang build fix] Signed-off-by: Jens Axboe

nvme-apple: Add initial Apple SoC NVMe driver

2022-05-02T15:24:45Z

Apple SoCs such as the M1 come with an embedded NVMe controller that is not attached to any PCIe bus. Additionally, it doesn't conform to the NVMe specification and requires a bunch of changes to command submission and IOMMU configuration to work. Reviewed-by: Christoph Hellwig Reviewed-by: Arnd Bergmann Signed-off-by: Sven Peter

nvme: add verbose error logging

2022-02-28T11:45:06Z

Improves logging of NVMe errors. If NVME_VERBOSE_ERRORS is configured, a verbose description of the error is logged, otherwise only status codes/bits is logged. Signed-off-by: Chaitanya Kulkarni [kch]: fix several nits, cosmetics, and trim down code. Signed-off-by: Martin K. Petersen Signed-off-by: Alan Adamson Reviewed-by: Himanshu Madhani Reviewed-by: Keith Busch Signed-off-by: Christoph Hellwig

remove the lightnvm subsystem

2021-08-14T21:54:09Z

Lightnvm supports the OCSSD 1.x and 2.0 specs which were early attempts to produce Open Channel SSDs and never made it into the NVMe spec proper. They have since been superceeded by NVMe enhancements such as ZNS support. Remove the support per the deprecation schedule. Signed-off-by: Christoph Hellwig Link: https://lore.kernel.org/r/20210812132308.38486-1-hch@lst.de Reviewed-by: Matias Bjørling Reviewed-by: Javier González Signed-off-by: Jens Axboe

nvme: move the ioctl code to a separate file

2021-04-15T06:12:55Z

Split out the ioctl code from core.c into a new file. Also update copyrights while we're at it. Signed-off-by: Christoph Hellwig Reviewed-by: Keith Busch Reviewed-by: Javier González Reviewed-by: Chaitanya Kulkarni

nvme: support for zoned namespaces

2020-07-08T14:16:20Z

Add support for NVM Express Zoned Namespaces (ZNS) Command Set defined in NVM Express TP4053. Zoned namespaces are discovered based on their Command Set Identifier reported in the namespaces Namespace Identification Descriptor list. A successfully discovered Zoned Namespace will be registered with the block layer as a host managed zoned block device with Zone Append command support. A namespace that does not support append is not supported by the driver. Reviewed-by: Martin K. Petersen Reviewed-by: Johannes Thumshirn Reviewed-by: Hannes Reinecke Reviewed-by: Sagi Grimberg Reviewed-by: Javier González Reviewed-by: Himanshu Madhani Signed-off-by: Hans Holmberg Signed-off-by: Dmitry Fomichev Signed-off-by: Ajay Joshi Signed-off-by: Aravind Ramesh Signed-off-by: Niklas Cassel Signed-off-by: Matias Bjørling Signed-off-by: Damien Le Moal Signed-off-by: Keith Busch Signed-off-by: Christoph Hellwig

nvme: Add hardware monitoring support

2019-11-11T16:57:35Z

nvme devices report temperature information in the controller information (for limits) and in the smart log. Currently, the only means to retrieve this information is the nvme command line interface, which requires super-user privileges. At the same time, it would be desirable to be able to use NVMe temperature information for thermal control. This patch adds support to read NVMe temperatures from the kernel using the hwmon API and adds temperature zones for NVMe drives. The thermal subsystem can use this information to set thermal policies, and userspace can access it using libsensors and/or the "sensors" command. Example output from the "sensors" command: nvme0-pci-0100 Adapter: PCI adapter Composite: +39.0°C (high = +85.0°C, crit = +85.0°C) Sensor 1: +39.0°C Sensor 2: +41.0°C Reviewed-by: Christoph Hellwig Signed-off-by: Guenter Roeck Signed-off-by: Keith Busch

nvme-tcp: add NVMe over TCP host driver

2018-12-13T08:58:58Z

This patch implements the NVMe over TCP host driver. It can be used to connect to remote NVMe over Fabrics subsystems over good old TCP/IP. The driver implements the TP 8000 of how nvme over fabrics capsules and data are encapsulated in nvme-tcp pdus and exchaged on top of a TCP byte stream. nvme-tcp header and data digest are supported as well. To connect to all NVMe over Fabrics controllers reachable on a given taget port over TCP use the following command: nvme connect-all -t tcp -a $IPADDR This requires the latest version of nvme-cli with TCP support. Signed-off-by: Sagi Grimberg Signed-off-by: Roy Shterman Signed-off-by: Solganik Alexander Signed-off-by: Christoph Hellwig

nvme: Add fault injection feature

2018-03-26T14:53:43Z

Linux's fault injection framework provides a systematic way to support error injection via debugfs in the /sys/kernel/debug directory. This patch uses the framework to add error injection to NVMe driver. The fault injection source code is stored in a separate file and only linked if CONFIG_FAULT_INJECTION_DEBUG_FS kernel config is selected. Once the error injection is enabled, NVME_SC_INVALID_OPCODE with no retry will be injected into the nvme_end_request. Users can change the default status code and no retry flag via debufs. Following example shows how to enable and inject an error. For more examples, refer to Documentation/fault-injection/nvme-fault-injection.txt How to enable nvme fault injection: First, enable CONFIG_FAULT_INJECTION_DEBUG_FS kernel config, recompile the kernel. After booting up the kernel, do the following. How to inject an error: mount /dev/nvme0n1 /mnt echo 1 > /sys/kernel/debug/nvme0n1/fault_inject/times echo 100 > /sys/kernel/debug/nvme0n1/fault_inject/probability cp a.file /mnt Expected Result: cp: cannot stat ‘/mnt/a.file’: Input/output error Message from dmesg: FAULT_INJECTION: forcing a failure. name fault_inject, interval 1, probability 100, space 0, times 1 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.15.0-rc8+ #2 Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 Call Trace: dump_stack+0x5c/0x7d should_fail+0x148/0x170 nvme_should_fail+0x2f/0x50 [nvme_core] nvme_process_cq+0xe7/0x1d0 [nvme] nvme_irq+0x1e/0x40 [nvme] __handle_irq_event_percpu+0x3a/0x190 handle_irq_event_percpu+0x30/0x70 handle_irq_event+0x36/0x60 handle_fasteoi_irq+0x78/0x120 handle_irq+0xa7/0x130 ? tick_irq_enter+0xa8/0xc0 do_IRQ+0x43/0xc0 common_interrupt+0xa2/0xa2 RIP: 0010:native_safe_halt+0x2/0x10 RSP: 0018:ffffffff82003e90 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffdd RAX: ffffffff817a10c0 RBX: ffffffff82012480 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 000000008e38ce64 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff82012480 R13: ffffffff82012480 R14: 0000000000000000 R15: 0000000000000000 ? __sched_text_end+0x4/0x4 default_idle+0x18/0xf0 do_idle+0x150/0x1d0 cpu_startup_entry+0x6f/0x80 start_kernel+0x4c4/0x4e4 ? set_init_arg+0x55/0x55 secondary_startup_64+0xa5/0xb0 print_req_error: I/O error, dev nvme0n1, sector 9240 EXT4-fs error (device nvme0n1): ext4_find_entry:1436: inode #2: comm cp: reading directory lblock 0 Signed-off-by: Thomas Tai Reviewed-by: Eric Saint-Etienne Signed-off-by: Karl Volz Reviewed-by: Keith Busch Signed-off-by: Sagi Grimberg Signed-off-by: Jens Axboe