linux-dev/drivers/pinctrl, branch master

pinctrl: ocelot: Fix incorrect trigger of the interrupt.

2022-10-18T08:42:10Z

The interrupt controller can detect only link changes. So in case an external device generated a level based interrupt, then the interrupt controller detected correctly the first edge. But the problem was that the interrupt controller was detecting also the edge when the interrupt was cleared. So it would generate another interrupt. The fix for this is to clear the second interrupt but still check the interrupt line status. Fixes: c297561bc98a ("pinctrl: ocelot: Fix interrupt controller") Signed-off-by: Horatiu Vultur Tested-by: Michael Walle Link: https://lore.kernel.org/r/20221018070959.1322606-1-horatiu.vultur@microchip.com Signed-off-by: Linus Walleij

Revert "pinctrl: pinctrl-zynqmp: Add support for output-enable and bias-high-impedance"

2022-10-18T07:50:29Z

This reverts commit ad2bea79ef0144043721d4893eef719c907e2e63. On systems with older PMUFW (Xilinx ZynqMP Platform Management Firmware) using these pinctrl properties can cause system hang because there is missing feature autodetection. When this feature is implemented in the PMUFW, support for these two properties should bring back. Cc: stable@vger.kernel.org Signed-off-by: Sai Krishna Potthuri Acked-by: Michal Simek Link: https://lore.kernel.org/r/20221017130303.21746-2-sai.krishna.potthuri@amd.com Signed-off-by: Linus Walleij

pinctrl: qcom: Avoid glitching lines when we first mux to output

2022-10-17T10:28:26Z

Back in the description of commit e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at bootup on trogdor") we described a problem that we were seeing on trogdor devices. I'll re-summarize here but you can also re-read the original commit. On trogdor devices, the BIOS is setting up the SPI chip select as: - mux special function (SPI chip select) - output enable - output low (unused because we've muxed as special function) In the kernel, however, we've moved away from using the chip select line as special function. Since the kernel wants to fully control the chip select it's far more efficient to treat the line as a GPIO rather than sending packet-like commands to the GENI firmware every time we want the line to toggle. When we transition from how the BIOS had the pin configured to how the kernel has the pin configured we end up glitching the line. That's because we _first_ change the mux of the line and then later set its output. This glitch is bad and can confuse the device on the other end of the line. The old commit e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at bootup on trogdor") fixed the glitch, though the solution was far from elegant. It essentially did the thing that everyone always hates: encoding a sequential program in device tree, even if it's a simple one. It also, unfortunately, got broken by commit b991f8c3622c ("pinctrl: core: Handling pinmux and pinconf separately"). After that commit we did all the muxing _first_ even though the config (set the pin to output high) was listed first. :( I looked at ideas for how to solve this more properly. My first thought was to use the "init" pinctrl state. In theory the "init" pinctrl state is supposed to be exactly for achieving glitch-free transitions. My dream would have been for the "init" pinctrl to do nothing at all. That would let us delay the automatic pin muxing until the driver could set things up and call pinctrl_init_done(). In other words, my dream was: /* Request the GPIO; init it 1 (because DT says GPIO_ACTIVE_LOW) */ devm_gpiod_get_index(dev, "cs", GPIOD_OUT_LOW); /* Output should be right, so we can remux, yay! */ pinctrl_init_done(dev); Unfortunately, it didn't work out. The primary reason is that the MSM GPIO driver implements gpio_request_enable(). As documented in pinmux.h, that function automatically remuxes a line as a GPIO. ...and it does this remuxing _before_ specifying the output of the pin. You can see in gpiod_get_index() that we call gpiod_request() before gpiod_configure_flags(). gpiod_request() isn't passed any flags so it has no idea what the eventual output will be. We could have debates about whether or not the automatic remuxing to GPIO for the MSM pinctrl was a good idea or not, but at this point I think there is a plethora of code that's relying on it and I certainly wouldn't suggest changing it. Alternatively, we could try to come up with a way to pass the initial output state to gpio_request_enable() and plumb all that through. That seems like it would be doable, but we'd have to plumb it through several layers in the stack. This patch implements yet another alternative. Here, we specifically avoid glitching the first time a pin is muxed to GPIO function if the direction of the pin is output. The idea is that we can read the state of the pin before we set the mux and make sure that the re-mux won't change the state. NOTES: - We only do this the first time since later swaps between mux states might want to preserve the old output value. In other words, I wouldn't want to break a driver that did: gpiod_set_value(g, 1); pinctrl_select_state(pinctrl, special_state); pinctrl_select_default_state(); /* We should be driving 1 even if "special_state" made the pin 0 */ - It's safe to do this the first time since the driver _couldn't_ have explicitly set a state. In order to even be able to control the GPIO (at least using gpiod) we have to have requested it which would have counted as the first mux. - In theory, instead of keeping track of the first time a pin was set as a GPIO we could enable the glitch-free behavior only when msm_pinmux_request_gpio() is in the callchain. That works an enables my "dream" implementation above where we use an "init" state to solve this. However, it's nice not to have to do this. By handling just the first transition to GPIO we can simply let the normal "default" remuxing happen and we can be assured that there won't be a glitch. Before this change I could see the glitch reported on the EC console when booting. It would say this when booting the kernel: Unexpected state 1 in CSNRE ISR After this change there is no error reported. Note that I haven't reproduced the original problem described in e440e30e26dd ("arm64: dts: qcom: sc7180: Avoid glitching SPI CS at bootup on trogdor") but I could believe it might happen in certain timing conditions. Fixes: b991f8c3622c ("pinctrl: core: Handling pinmux and pinconf separately") Signed-off-by: Douglas Anderson Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/20221014103217.1.I656bb2c976ed626e5d37294eb252c1cf3be769dc@changeid Signed-off-by: Linus Walleij

pinctrl: Ingenic: JZ4755 bug fixes

2022-10-17T09:47:38Z

Fixes UART1 function bits and MMC groups typo. For pins 0x97,0x99 function 0 is designated to PWM3/PWM5 respectively, function is 1 designated to the UART1. Diff from v1: - sent separately - added tag Fixes Cc: stable@vger.kernel.org Fixes: b582b5a434d3 ("pinctrl: Ingenic: Add pinctrl driver for JZ4755.") Tested-by: Siarhei Volkau Signed-off-by: Siarhei Volkau Link: https://lore.kernel.org/r/20221016153548.3024209-1-lis8215@gmail.com Signed-off-by: Linus Walleij

Merge tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

2022-10-12T17:23:24Z

Pull interrupt updates from Thomas Gleixner: "Core code: - Provide a generic wrapper which can be utilized in drivers to handle the problem of force threaded demultiplex interrupts on RT enabled kernels. This avoids conditionals and horrible quirks in drivers all over the place - Fix up affected pinctrl and GPIO drivers to make them cleanly RT safe Interrupt drivers: - A new driver for the FSL MU platform specific MSI implementation - Make irqchip_init() available for pure ACPI based systems - Provide a functional DT binding for the Realtek RTL interrupt chip - The usual DT updates and small code improvements all over the place" * tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits) irqchip: IMX_MU_MSI should depend on ARCH_MXC irqchip/imx-mu-msi: Fix wrong register offset for 8ulp irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap dt-bindings: irqchip: Describe the IMX MU block as a MSI controller irqchip: Add IMX MU MSI controller driver dt-bindings: irqchip: renesas,irqc: Add r8a779g0 support irqchip/gic-v3: Fix typo in comment dt-bindings: interrupt-controller: ti,sci-intr: Fix missing reg property in the binding dt-bindings: irqchip: ti,sci-inta: Fix warning for missing #interrupt-cells irqchip: Allow extra fields to be passed to IRQCHIP_PLATFORM_DRIVER_END platform-msi: Export symbol platform_msi_create_irq_domain() irqchip/realtek-rtl: use parent interrupts dt-bindings: interrupt-controller: realtek,rtl-intc: require parents irqchip/realtek-rtl: use irq_domain_add_linear() irqchip: Make irqchip_init() usable on pure ACPI systems bcma: gpio: Use generic_handle_irq_safe() gpio: mlxbf2: Use generic_handle_irq_safe() platform/x86: intel_int0002_vgpio: Use generic_handle_irq_safe() ssb: gpio: Use generic_handle_irq_safe() pinctrl: amd: Use generic_handle_irq_safe() ...

Merge tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

2022-10-11T17:59:59Z

Pull pin control updates from Linus Walleij: "There is nothing exciting going on, no core changes, just a few drivers and cleanups. New drivers: - Cypress CY8C95x0 chip pin control support, along with an immediate cleanup - Mediatek MT8188 SoC pin control support - Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem) pin control support - Qualcomm PM7250, PM8450 - Rockchip RV1126 SoC pin control support Improvements: - Fix some missing pins in the Armada 37xx driver - Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP() macro - Fix some GPIO irq_chips to be immutable - Massive Qualcomm device tree binding cleanup, with more to come" * tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (119 commits) MAINTAINERS: adjust STARFIVE JH7100 PINCTRL DRIVER after file movement pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100" pinctrl: Create subdirectory for StarFive drivers dt-bindings: pinctrl: st,stm32: Document interrupt-controller property dt-bindings: pinctrl: st,stm32: Document gpio-hog pattern property dt-bindings: pinctrl: st,stm32: Document gpio-line-names pinctrl: st: stop abusing of_get_named_gpio() pinctrl: wpcm450: Correct the fwnode_irq_get() return value check pinctrl: bcm: Remove unused struct bcm6328_pingroup pinctrl: qcom: restrict drivers per ARM/ARM64 pinctrl: bcm: ns: Remove redundant dev_err call gpio: rockchip: request GPIO mux to pinctrl when setting direction pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback pinctrl: cy8c95x0: Align function names in cy8c95x0_pmxops pinctrl: cy8c95x0: Drop atomicity on operations on push_pull pinctrl: cy8c95x0: Lock register accesses in cy8c95x0_set_mux() pinctrl: sunxi: sun50i-h5: Switch to use dev_err_probe() helper pinctrl: stm32: Switch to use dev_err_probe() helper dt-bindings: qcom-pmic-gpio: Add PM7250B and PM8450 bindings pinctrl: qcom: spmi-gpio: Add compatible for PM7250B ...

Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2022-10-06T18:04:57Z

Pull ARM driver updates from Arnd Bergmann: "The drivers branch for 6.1 is a bit larger than for most releases. Most of the changes come from SoC maintainers for the drivers/soc subsystem: - A new driver for error handling on the NVIDIA Tegra 'control backbone' bus. - A new driver for Qualcomm LLCC/DDR bandwidth measurement - New Rockchip rv1126 and rk3588 power domain drivers - DT binding updates for memory controllers, older Rockchip SoCs, various Mediatek devices, Qualcomm SCM firmware - Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the Apple rtkit firmware driver, Tegra firmware - Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra, Qualcomm, Broadcom, NXP, ...) There are also some separate subsystem with downstream maintainers that merge updates this way: - Various updates and new drivers in the memory controller subsystem for Mediatek and Broadcom SoCs - Small set of changes in preparation to add support for FF-A v1.1 specification later, in the Arm FF-A firmware subsystem - debugfs support in the PSCI firmware subsystem" * tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits) ARM: remove check for CONFIG_DEBUG_LL_SER3 firmware/psci: Add debugfs support to ease debugging firmware/psci: Print a warning if PSCI doesn't accept PC mode dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support soc: sunxi: sram: Add support for the D1 system control soc: sunxi: sram: Export the LDO control register soc: sunxi: sram: Save a pointer to the OF match data soc: sunxi: sram: Return void from the release function soc: apple: rtkit: Add apple_rtkit_poll soc: imx: add i.MX93 media blk ctrl driver soc: imx: add i.MX93 SRC power domain driver soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl soc: imx: add icc paths for i.MX8MP media blk ctrl ...

pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100"

2022-10-04T08:47:48Z

Add the SoC name to make it more clear. Also the next generation StarFive SoCs will use "pinctrl-starfive" as the core of StarFive pinctrl driver. No functional change. Signed-off-by: Jianlong Huang Signed-off-by: Hal Feng Reviewed-by: Rob Herring Link: https://lore.kernel.org/r/20220930061404.5418-1-hal.feng@linux.starfivetech.com Signed-off-by: Linus Walleij

pinctrl: Create subdirectory for StarFive drivers

2022-10-04T08:42:11Z

Move the StarFive JH7100 pinctrl driver to a new subdirectory in preparation for adding more StarFive pinctrl drivers. No functional change. Signed-off-by: Jianlong Huang Signed-off-by: Hal Feng Link: https://lore.kernel.org/r/20220930060819.5320-1-hal.feng@linux.starfivetech.com Signed-off-by: Linus Walleij

pinctrl: st: stop abusing of_get_named_gpio()

2022-10-04T07:58:17Z

Pin descriptions for this chip only look like standard GPIO device tree descriptions, while in fact they contain additional data (in excess of number of cells specified in description of gpio controllers). They also refer to only pins/gpios belonging to the driver and not to arbitrary gpio in the system. Because we want to stop exporting OF-specific handlers from gpiolib-of, let's parse the pin reference ourself instead of trying to call of_get_named_gpio(). Signed-off-by: Dmitry Torokhov Tested-by: Patrice Chotard Reviewed-by: Patrice Chotard Link: https://lore.kernel.org/r/YzSsgoVoJn4+mSpv@google.com Signed-off-by: Linus Walleij