linux-dev/drivers/s390/crypto/zcrypt_api.h, branch linus/master

s390/zcrypt: code cleanup

2022-04-25T11:54:14Z

This patch tries to fix as much as possible of the checkpatch.pl --strict findings: CHECK: Logical continuations should be on the previous line CHECK: No space is necessary after a cast CHECK: Alignment should match open parenthesis CHECK: 'useable' may be misspelled - perhaps 'usable'? WARNING: Possible repeated word: 'is' CHECK: spaces preferred around that '*' (ctx:VxV) CHECK: Comparison to NULL could be written "!msg" CHECK: Prefer kzalloc(sizeof(*zc)...) over kzalloc(sizeof(struct...)...) CHECK: Unnecessary parentheses around resp_type->work CHECK: Avoid CamelCase: There is no functional change comming with this patch, only code cleanup, renaming, whitespaces, indenting, ... but no semantic change in any way. Also the API (zcrypt and pkey header file) is semantically unchanged. Signed-off-by: Harald Freudenberger Reviewed-by: Jürgen Christ Signed-off-by: Heiko Carstens

s390/ap/zcrypt: notify userspace with online, config and mode info

2021-06-16T21:46:18Z

This patch brings 3 reworked/new uevent changes: * All AP uevents caused by an ap card or queue device now carry an additional uevent env value MODE=. Here is an example: KERNEL[1267.301292] add /devices/ap/card0a (ap) ACTION=add DEVPATH=/devices/ap/card0a SUBSYSTEM=ap DEVTYPE=ap_card DEV_TYPE=000D MODALIAS=ap:t0D MODE=ep11 <- this is new SEQNUM=1095 This is true for bind, unbind, add, remove, and change uevents related to ap card or ap queue devices. * On a change of the soft online attribute on a zcrypt queue or card device a new CHANGE uevent is sent with an env value ONLINE=<0|1>. Example uevent: KERNEL[613.067531] change /devices/ap/card09/09.0011 (ap) ACTION=change DEVPATH=/devices/ap/card09/09.0011 SUBSYSTEM=ap ONLINE=0 <- this is new DEVTYPE=ap_queue DRIVER=cex4queue MODE=cca SEQNUM=1070 - On a change of the config state of an zcrypt card device a new CHANGE uevent is sent with an env value CONFIG=<0|1>. Example uevent: KERNEL[876.258680] change /devices/ap/card09 (ap) ACTION=change DEVPATH=/devices/ap/card09 SUBSYSTEM=ap CONFIG=0 <- this is new DEVTYPE=ap_card DRIVER=cex4card DEV_TYPE=000D MODALIAS=ap:t0D MODE=cca SEQNUM=1073 Setting a card config on/off causes the dependent queue devices to follow the config state change and thus uevents informing about the config state change for the queue devices are also emitted. Signed-off-by: Harald Freudenberger Reviewed-by: Ingo Franzki Signed-off-by: Vasily Gorbik

s390/zcrypt: remove zcrypt_device_count

2021-06-07T15:06:59Z

It's evidently unused. Signed-off-by: Julian Wiedmann Reviewed-by: Harald Freudenberger Signed-off-by: Vasily Gorbik

s390/zcrypt/pkey: introduce zcrypt_wait_api_operational() function

2020-11-09T10:21:00Z

The zcrypt api provides a new function to wait until the zcrypt api is operational: int zcrypt_wait_api_operational(void); The AP bus scan and the binding of ap devices to device drivers is an asynchronous job. This function waits until these initial jobs are done and so the zcrypt api should be ready to serve crypto requests - if there are resources available. The function uses an internal timeout of 60s. The very first caller will either wait for ap bus bindings complete or the timeout happens. This state will be remembered for further callers which will only be blocked until a decision is made (timeout or bindings complete). Reviewed-by: Ingo Franzki Signed-off-by: Harald Freudenberger Signed-off-by: Heiko Carstens

s390/zcrypt: Introduce Failure Injection feature

2020-10-07T19:50:01Z

Introduce a way to specify additional debug flags with an crpyto request to be able to trigger certain failures within the zcrypt device drivers and/or ap core code. This failure injection possibility is only enabled with a kernel debug build CONFIG_ZCRYPT_DEBUG) and should never be available on a regular kernel running in production environment. Details: * The ioctl(ICARSAMODEXPO) get's a struct ica_rsa_modexpo. If the leftmost bit of the 32 bit unsigned int inputdatalength field is set, the uppermost 16 bits are separated and used as debug flag value. The process is checked to have the CAP_SYS_ADMIN capability enabled or EPERM is returned. * The ioctl(ICARSACRT) get's a struct ica_rsa_modexpo_crt. If the leftmost bit of the 32 bit unsigned int inputdatalength field is set, the uppermost 16 bits are separated and used als debug flag value. The process is checked to have the CAP_SYS_ADMIN capability enabled or EPERM is returned. * The ioctl(ZSECSENDCPRB) used to send CCA CPRBs get's a struct ica_xcRB. If the leftmost bit of the 32 bit unsigned int status field is set, the uppermost 16 bits of this field are used as debug flag value. The process is checked to have the CAP_SYS_ADMIN capability enabled or EPERM is returned. * The ioctl(ZSENDEP11CPRB) used to send EP11 CPRBs get's a struct ep11_urb. If the leftmost bit of the 64 bit unsigned int req_len field is set, the uppermost 16 bits of this field are used as debug flag value. The process is checked to have the CAP_SYS_ADMIN capability enabled or EPERM is returned. So it is possible to send an additional 16 bit value to the zcrypt API to be used to carry a failure injection command which may trigger special behavior within the zcrypt API and layers below. This 16 bit value is for the rest of the test referred as 'fi command' for Failure Injection. The lower 8 bits of the fi command construct a numerical argument in the range of 1-255 and is the 'fi action' to be performed with the request or the resulting reply: * 0x00 (all requests): No failure injection action but flags may be provided which may affect the processing of the request or reply. * 0x01 (only CCA CPRBs): The CPRB's agent_ID field is set to 'FF'. This results in an reply code 0x90 (Transport-Protocol Failure). * 0x02 (only CCA CPRBs): After the APQN to send to has been chosen, the domain field within the CPRB is overwritten with value 99 to enforce an reply with RY 0x8A. * 0x03 (all requests): At NQAP invocation the invalid qid value 0xFF00 is used causing an response code of 0x01 (AP queue not valid). The upper 8 bits of the fi command may carry bit flags which may influence the processing of an request or response: * 0x01: No retry. If this bit is set, the usual loop in the zcrypt API which retries an CPRB up to 10 times when the lower layers return with EAGAIN is abandoned after the first attempt to send the CPRB. * 0x02: Toggle special. Toggles the special bit on this request. This should result in an reply code RY~0x41 and result in an ioctl failure with errno EINVAL. This failure injection possibilities may get some further extensions in the future. As of now this is a starting point for Continuous Test and Integration to trigger some failures and watch for the reaction of the ap bus and zcrypt device driver code. Signed-off-by: Harald Freudenberger Signed-off-by: Vasily Gorbik

s390/zcrypt: move ap_msg param one level up the call chain

2020-10-07T19:50:01Z

Move the creating and disposal of the struct ap_message one level up the call chain. The ap message was constructed in the calling functions in msgtype50 and msgtype6 but only for the ica rsa messages. For CCA and EP11 CPRBs the ap message struct is created in the zcrypt api functions. This patch moves the construction of the ap message struct into the functions zcrypt_rsa_modexpo and zcrypt_rsa_crt. So now all the 4 zcrypt api functions zcrypt_rsa_modexpo, zcrypt_rsa_crt, zcrypt_send_cprb and zcrypt_send_ep11_cprb appear and act similar. There are no functional changes coming with this patch. However, the availability of the ap_message struct has advantages which will be needed by a follow up patch. Signed-off-by: Harald Freudenberger Signed-off-by: Vasily Gorbik

s390/zcrypt: introduce msg tracking in zcrypt functions

2020-10-07T19:49:59Z

Introduce a new internal struct zcrypt_track with an retry counter field and a last return code field. Fill and update these fields at certain points during processing of an request/reply. This tracking info is then used to - avoid trying to resend the message forever. Now each message is tried to be send TRACK_AGAIN_MAX (currently 10) times and then the ioctl returns to userspace with errno EAGAIN. - avoid trying to resend the message on the very same card/domain. If possible (more than one APQN with same quality) don't use the very same qid as the previous attempt when again scheduling the request. This is done by adding penalty weight values when the dispatching takes place. There is a penalty TRACK_AGAIN_CARD_WEIGHT_PENALTY for using the same card as previously and another penalty define TRACK_AGAIN_QUEUE_WEIGHT_PENALTY to be considered when the same qid as the previous sent attempt is calculated. Both values make it harder to choose the very same card/domain but not impossible. For example when only one APQN is available a resend can only address the very same APQN. There are some more ideas for the future to extend the use of this tracking information. For example the last response code at NQAP and DQAP could be stored there, giving the possibility to extended tracing and debugging about requests failing to get processed properly. Signed-off-by: Harald Freudenberger Signed-off-by: Vasily Gorbik

s390/zcrypt: remove set_fs() invocation in zcrypt device driver

2020-09-17T12:11:03Z

This patch reworks the zcrypt device driver so that the set_fs() invocation is not needed any more. Instead there is a new flag bool userspace passed through all the functions which tells if the pointer arguments are userspace or kernelspace. Together with the two new inline functions z_copy_from_user() and z_copy_to_user() which either invoke copy_from_user (userspace is true) or memcpy (userspace is false) the zcrypt dd and the AP bus now has no requirement for the set_fs() functionality any more. Signed-off-by: Harald Freudenberger Reviewed-by: Ingo Franzki Reviewed-by: Christoph Hellwig Signed-off-by: Heiko Carstens Signed-off-by: Vasily Gorbik

s390/zcrypt: ep11 structs rework, export zcrypt_send_ep11_cprb

2020-01-30T12:07:55Z

Minor rework for struct ep11_cprb and struct ep11_urb. Use of u8, u16, u32 instead of unsigned char. Declare pointers to mem from userspace with __user to give sparse a chance to check. Export zcrypt_send_ep11_cprb() function as this function will be called by code in progress which will build ep11 cprbs within the zcrypt device driver zoo and send them to EP11 crypto cards. Signed-off-by: Harald Freudenberger Signed-off-by: Vasily Gorbik

s390/zcrypt: CEX7S exploitation support

2019-09-19T10:56:06Z

This patch adds CEX7 exploitation support for the AP bus code, the zcrypt device driver zoo and the vfio device driver. Signed-off-by: Harald Freudenberger Reviewed-by: Ingo Franzki Signed-off-by: Vasily Gorbik