linux-dev/drivers/scsi/pm8001, branch linus/master

scsi: pm80xx: Enable upper inbound, outbound queues

2022-04-12T01:59:50Z

Executing driver on servers with more than 32 CPUs were faced with command timeouts. This is because we were not geting completions for commands submitted on IQ32 - IQ63. Set E64Q bit to enable upper inbound and outbound queues 32 to 63 in the MPI main configuration table. Added 500ms delay after successful MPI initialization as mentioned in controller datasheet. Link: https://lore.kernel.org/r/20220411064603.668448-3-Ajish.Koshy@microchip.com Fixes: 05c6c029a44d ("scsi: pm80xx: Increase number of supported queues") Reviewed-by: Damien Le Moal Acked-by: Jack Wang Signed-off-by: Ajish Koshy Signed-off-by: Viswas G Signed-off-by: Martin K. Petersen

scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63

2022-04-12T01:59:49Z

When upper inbound and outbound queues 32-63 are enabled, we see upper vectors 32-63 in interrupt service routine. We need corresponding registers to handle masking and unmasking of these upper interrupts. To achieve this, we use registers MSGU_ODMR_U(0x34) to mask and MSGU_ODMR_CLR_U(0x3C) to unmask the interrupts. In these registers bit 0-31 represents interrupt vectors 32-63. Link: https://lore.kernel.org/r/20220411064603.668448-2-Ajish.Koshy@microchip.com Fixes: 05c6c029a44d ("scsi: pm80xx: Increase number of supported queues") Reviewed-by: John Garry Acked-by: Jack Wang Signed-off-by: Ajish Koshy Signed-off-by: Viswas G Signed-off-by: Martin K. Petersen

scsi: pm8001: Use libsas internal abort support

2022-03-15T03:33:24Z

New special handling is added for SAS_PROTOCOL_INTERNAL_ABORT proto so that we may use the common queue command API. Link: https://lore.kernel.org/r/1647001432-239276-4-git-send-email-john.garry@huawei.com Tested-by: Damien Le Moal Acked-by: Jack Wang Signed-off-by: John Garry Signed-off-by: Martin K. Petersen

scsi: pm80xx: Handle non-fatal errors

2022-02-28T02:37:28Z

Firmware expects host driver to clear scratchpad rsvd 0 register after non-fatal error is found. This is done when firmware raises fatal error interrupt and indicates non-fatal error. At this point firmware updates scratchpad rsvd 0 register with non-fatal error value. Here host has to clear the register after reading it during non-fatal errors. Rename: - MSGU_HOST_SCRATCH_PAD_6 to MSGU_SCRATCH_PAD_RSVD_0 - MSGU_HOST_SCRATCH_PAD_7 to MSGU_SCRATCH_PAD_RSVD_1 Link: https://lore.kernel.org/r/20220222092618.108198-1-Ajish.Koshy@microchip.com Reviewed-by: Damien Le Moal Acked-by: Jack Wang Signed-off-by: Ajish Koshy Signed-off-by: Viswas G Signed-off-by: Martin K. Petersen

scsi: pm8001: Fix pm8001_info() message format

2022-02-23T02:31:21Z

Make the driver messages more readable by adding a space after the message prefix ":" and removing the extra space between function name and line number. Link: https://lore.kernel.org/r/20220220031810.738362-32-damien.lemoal@opensource.wdc.com Reviewed-by: Jack Wang Signed-off-by: Damien Le Moal Signed-off-by: Martin K. Petersen

scsi: pm8001: Improve pm80XX_send_abort_all()

2022-02-23T02:31:21Z

Both pm8001_send_abort_all() and pm80xx_send_abort_all() are called only for a non null device with the NCQ_READ_LOG_FLAG set, so remove the device check on entry of these functions. Furthermore, setting the NCQ_ABORT_ALL_FLAG device id flag and clearing the NCQ_READ_LOG_FLAG is always done before calling these functions. Move these operations inside the functions. Link: https://lore.kernel.org/r/20220220031810.738362-31-damien.lemoal@opensource.wdc.com Reviewed-by: Jack Wang Signed-off-by: Damien Le Moal Signed-off-by: Martin K. Petersen

scsi: pm8001: Simplify pm8001_ccb_task_free()

2022-02-23T02:31:21Z

The task argument of the pm8001_ccb_task_free() function can be inferred from the ccb argument ccb_task field. So there is no need to have this argument. Likewise, the ccb_index argument is always equal to the ccb tag field and is not needed either. Remove both arguments and update all call sites. The pm8001_ccb_task_free_done() helper is also modified to match this change. Link: https://lore.kernel.org/r/20220220031810.738362-30-damien.lemoal@opensource.wdc.com Reviewed-by: Jack Wang Signed-off-by: Damien Le Moal Signed-off-by: Martin K. Petersen

scsi: pm8001: Simplify pm8001_task_exec()

2022-02-23T02:31:21Z

The main part of the pm8001_task_exec() function uses a do {} while(0) loop that is useless and only makes the code harder to read. Remove this loop. The unnecessary local variable t is also removed. Additionally, avoid repeatedly declaring "struct task_status_struct *ts" to handle error cases by declaring this variable for the entire function scope. This allows simplifying the error cases, and together with the addition of blank lines make the code more readable. Finally, handling of the running_req counter is fixed to avoid decrementing it without a corresponding incrementation in the case of an invalid task protocol. Link: https://lore.kernel.org/r/20220220031810.738362-29-damien.lemoal@opensource.wdc.com Reviewed-by: John Garry Reviewed-by: Jack Wang Signed-off-by: Damien Le Moal Signed-off-by: Martin K. Petersen

scsi: pm8001: Simplify pm8001_mpi_build_cmd() interface

2022-02-23T02:31:21Z

There is no need to pass a pointer to a struct inbound_queue_table to pm8001_mpi_build_cmd(). Passing the start index in the inbound queue table of the adapter is enough. This change allows avoiding the declaration of a struct inbound_queue_table pointer (circularQ variables) in many functions, simplifying the code. While at it, blank lines are added i(e.g. after local variable declarations) to make the code more readable. Link: https://lore.kernel.org/r/20220220031810.738362-28-damien.lemoal@opensource.wdc.com Reviewed-by: Jack Wang Signed-off-by: Damien Le Moal Signed-off-by: Martin K. Petersen

scsi: pm8001: Introduce ccb alloc/free helpers

2022-02-23T02:31:21Z

Introduce the pm8001_ccb_alloc() and pm8001_ccb_free() helpers to replace the typical code patterns: res = pm8001_tag_alloc(pm8001_ha, &ccb_tag); if (res) ... ccb = &pm8001_ha->ccb_info[ccb_tag]; ccb->device = pm8001_ha_dev; ccb->ccb_tag = ccb_tag; ccb->task = task; ccb->n_elem = 0; and ccb->task = NULL; ccb->ccb_tag = PM8001_INVALID_TAG; pm8001_tag_free(pm8001_ha, tag); With the simpler function calls: ccb = pm8001_ccb_alloc(pm8001_ha, pm8001_ha_dev, task); if (!ccb) ... and pm8001_ccb_free(pm8001_ha, ccb); The pm8001_ccb_alloc() helper ensures that all fields of the ccb info structure for the newly allocated tag are all initialized, except the buf_prd field. The pm8001_ccb_free() helper clears the initialized fields and the ccb tag to ensure that iteration over the adapter ccb_info array detects ccbs that are in use. All call site of the pm8001_tag_alloc() function that use a ccb info associated with an allocated tag are converted to use the new helpers. Link: https://lore.kernel.org/r/20220220031810.738362-27-damien.lemoal@opensource.wdc.com Reviewed-by: John Garry Reviewed-by: Jack Wang Signed-off-by: Damien Le Moal Signed-off-by: Martin K. Petersen