linux-dev/drivers/usb/dwc2/Kconfig, branch master

usb: dwc2: override PHY input signals with usb role switch support

2020-10-02T10:29:13Z

This patch adds support for usb role switch to dwc2, by using overriding control of the PHY voltage valid and ID input signals. iddig signal (ID) can be overridden: - when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1; - when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0. avalid/bvalid/vbusvalid signals can be overridden respectively with: - GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL - GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL - GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL It is possible to determine valid sessions thanks to usb role switch: - if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid - if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid - if USB_ROLE_HOST then avalid && !bvalid && vbusvalid Acked-by: Minas Harutyunyan Acked-by: Martin Blumenstingl Signed-off-by: Amelie Delaunay Signed-off-by: Felipe Balbi

usb: remove redundant 'default n' from Kconfig-s

2019-05-21T08:06:22Z

'default n' is the default value for any bool or tristate Kconfig setting so there is no need to write it explicitly. Also since commit f467c5640c29 ("kconfig: only write '# CONFIG_FOO is not set' for visible symbols") the Kconfig behavior is the same regardless of 'default n' being present or not: ... One side effect of (and the main motivation for) this change is making the following two definitions behave exactly the same: config FOO bool config FOO bool default n With this change, neither of these will generate a '# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied). That might make it clearer to people that a bare 'default n' is redundant. ... Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Greg Kroah-Hartman

USB: add missing SPDX lines to Kconfig and Makefiles

2019-01-22T08:08:17Z

There are a few remaining drivers/usb/ files that do not have SPDX identifiers in them, all of these are either Kconfig or Makefiles. Add the correct GPL-2.0 identifier to them to make scanning tools happy. Signed-off-by: Greg Kroah-Hartman

usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW

2017-03-17T04:16:56Z

a lot of embeded system SOC (e.g. freescale T2080) have both PCI and USB modules. But USB module is controlled by registers directly, it have no relationship with PCI module. when say N here it will not build PCI related code in USB driver. Signed-off-by: yuan linyu Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

USB: dwc2-usb: add USB_GADGET dependency

2016-06-29T08:11:41Z

The driver selects NOP_USB_XCEIV, which can only be built-in if USB_GADGET is either disabled or also built-in, so with USB_DWC2_PCI=y and USB_GADGET=m, NOP_USB_XCEIV is also built-in and we get this link error: drivers/usb/built-in.o: In function `nop_set_peripheral': (text+0x1927c): undefined reference to `usb_gadget_vbus_connect' drivers/usb/built-in.o: In function `nop_gpio_vbus_thread': (text+0x197a0): undefined reference to `usb_gadget_vbus_connect' (text+0x19830): undefined reference to `usb_gadget_vbus_disconnect' This adds the same dependency for the dwc2 driver to avoid that broken configuration. Signed-off-by: Arnd Bergmann Acked-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: USB_DWC2 should depend on HAS_DMA

2016-02-21T04:23:02Z

If NO_DMA=y: ERROR: "usb_gadget_map_request" [drivers/usb/dwc2/dwc2.ko] undefined! ERROR: "usb_gadget_unmap_request" [drivers/usb/dwc2/dwc2.ko] undefined! ERROR: "bad_dma_ops" [drivers/usb/dwc2/dwc2.ko] undefined! Add a dependency on HAS_DMA to fix this. Signed-off-by: Geert Uytterhoeven Acked-by: John Youn Signed-off-by: Greg Kroah-Hartman

usb: add HAS_IOMEM dependency to USB_DWC2

2016-02-15T01:09:56Z

drivers/built-in.o: In function `dwc2_driver_probe': /home/vegard/linux/drivers/usb/dwc2/platform.c:491: undefined reference to `devm_ioremap_resource' Signed-off-by: Vegard Nossum Signed-off-by: Greg Kroah-Hartman

usb: dwc2: remove dwc2_platform.ko

2015-04-29T20:20:11Z

As dwc2 pci module is now exporting dwc2 platform device, include platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko. dwc2.ko is the new platform driver. Remove all EXPORT_SYMBOL_GPL as they are not needed any more. Acked-by: John Youn Signed-off-by: Mian Yousaf Kaukab Signed-off-by: Felipe Balbi

usb: dwc2: pci: Select the generic PHY for dwc2-pci driver

2015-03-13T15:40:53Z

The dwc2-pci driver requires the generic PHY. This fixes undefined reference issues when it is not selected. Reported-by: kbuild test robot Signed-off-by: John Youn Signed-off-by: Felipe Balbi

usb: dwc2: pci: Add device mode to the dwc2-pci driver

2015-03-11T20:08:17Z

The pci driver now registers a platform driver, like in dwc3, and lets its probe function do all the initialization. This allows it to account for changes to the platform driver that were not added to the pci driver. Also future changes to the probe function don't have to be duplicated. This also has the effect of adding device and DRD mode to the pci driver. Tested on the Synopsys HAPS PCIe platform. Signed-off-by: John Youn Signed-off-by: Felipe Balbi