linux-dev/net/bluetooth/msft.c, branch linus/master

Bluetooth: msft: Clear tracked devices on resume

2022-03-18T16:12:08Z

Clear already tracked devices on system resume. Once the monitors are reregistered after resume, matched devices in range will be found again. Signed-off-by: Manish Mandlik Reviewed-by: Miao-chen Chou Signed-off-by: Marcel Holtmann

Bluetooth: msft: fix null pointer deref on msft_monitor_device_evt

2022-01-23T14:30:18Z

msft_find_handle_data returns NULL if it can't find the handle. Therefore, handle_data must be checked, otherwise a null pointer is dereferenced. Signed-off-by: Soenke Huster Signed-off-by: Marcel Holtmann

Bluetooth: mgmt: Add MGMT Adv Monitor Device Found/Lost events

2022-01-20T21:10:28Z

This patch introduces two new MGMT events for notifying the bluetoothd whenever the controller starts/stops monitoring a device. Test performed: - Verified by logs that the MSFT Monitor Device is received from the controller and the bluetoothd is notified whenever the controller starts/stops monitoring a device. Signed-off-by: Manish Mandlik Reviewed-by: Miao-chen Chou Signed-off-by: Luiz Augusto von Dentz

Bluetooth: msft: Handle MSFT Monitor Device Event

2022-01-20T21:10:21Z

Whenever the controller starts/stops monitoring a bt device, it sends MSFT Monitor Device event. Add handler to read this vendor event. Test performed: - Verified by logs that the MSFT Monitor Device event is received from the controller whenever it starts/stops monitoring a device. Signed-off-by: Manish Mandlik Reviewed-by: Miao-chen Chou Signed-off-by: Luiz Augusto von Dentz

Bluetooth: hci_event: Use of a function table to handle HCI events

2021-12-07T16:05:50Z

This change the use of switch statement to a function table which is easier to extend and can include min/max length of each HCI event. Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Marcel Holtmann

Bluetooth: hci_sync: Rework hci_suspend_notifier

2021-10-29T14:52:00Z

This makes hci_suspend_notifier use the hci_*_sync which can be executed synchronously which is allowed in the suspend_notifier and simplifies a lot of the handling since the status of each command can be checked inline so no other work need to be scheduled thus can be performed without using of a state machine. Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Marcel Holtmann

Bluetooth: hci_sync: Rework background scan

2021-10-29T14:51:58Z

This replaces the use of hci_update_background_scan with hci_update_passive_scan which runs from cmd_work_sync and deal properly with resolving list when LL privacy is enabled. Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Marcel Holtmann

Bluetooth: Fix Advertisement Monitor Suspend/Resume

2021-09-28T08:01:35Z

During system suspend, advertisement monitoring is disabled by setting the HCI_VS_MSFT_LE_Set_Advertisement_Filter_Enable to False. This disables the monitoring during suspend, however, if the controller is monitoring a device, it sends HCI_VS_MSFT_LE_Monitor_Device_Event to indicate that the monitoring has been stopped for that particular device. This event may occur after suspend depending on the low_threshold_timeout and peer device advertisement frequency, which causes early wake up. Right way to disable the monitoring for suspend is by removing all the monitors before suspend and re-monitor after resume to ensure no events are received during suspend. This patch fixes this suspend/resume issue. Following tests are performed: - Add monitors before suspend and make sure DeviceFound gets triggered - Suspend the system and verify that all monitors are removed by kernel but not Released by bluetoothd - Wake up and verify that all monitors are added again and DeviceFound gets triggered Signed-off-by: Manish Mandlik Reviewed-by: Archie Pusaka Reviewed-by: Miao-chen Chou Signed-off-by: Marcel Holtmann

Bluetooth: Keep MSFT ext info throughout a hci_dev's life cycle

2021-09-10T07:27:13Z

This splits the msft_do_{open/close} to msft_do_{open/close} and msft_{register/unregister}. With this change it is possible to retain the MSFT extension info irrespective of controller power on/off state. This helps bluetoothd to report correct 'supported features' of the controller to the D-Bus clients event if the controller is off. It also re-reads the MSFT info upon every msft_do_open(). The following test steps were performed. 1. Boot the test device and verify the MSFT support debug log in syslog. 2. Power off the controller and read the 'supported features', power on and read again. 3. Restart the bluetoothd and verify the 'supported features' value. Signed-off-by: Miao-chen Chou Reviewed-by: Abhishek Pandit-Subedi Reviewed-by: Archie Pusaka Reviewed-by: Alain Michaud Signed-off-by: Manish Mandlik Signed-off-by: Marcel Holtmann

Bluetooth: msft: Use the correct print format

2021-06-26T05:12:42Z

According to Documentation/core-api/printk-formats.rst, Use the correct print format. Printing an unsigned int value should use %u instead of %d. Otherwise printk() might end up displaying negative numbers. Signed-off-by: Kai Ye Signed-off-by: Marcel Holtmann