[PATCH] remove two obsolete net drivers

  
  The options FMV18X and SK_G16 do depend on the non-available
  CONFIG_OBSOLETE even in kernel 2.4 - IOW, the last time it was able to
  select them was in kernel 2.2 (or even before).
  
  Since it seems noone misses these drivers, this patch removes them.
  
  Signed-off-by: Adrian Bunk <bunk@stusta.de>
  Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

8 files changed, 0 insertions, 2955 deletions

diff --git a/Documentation/networking/multicast.txt b/Documentation/networking/multicast.txt
index 5049a64313d1..b06c8c69266f 100644
--- a/Documentation/networking/multicast.txt
+++ b/Documentation/networking/multicast.txt
@@ -47,7 +47,6 @@ ni52		<------------------ Buggy ------------------>
 ni65		YES		YES		YES		Software(#)
 seeq		NO		NO		NO		N/A
 sgiseek		<------------------ Buggy ------------------>
-sk_g16		NO		NO		YES		N/A
 smc-ultra	YES		YES		YES		Hardware
 sunlance	YES		YES		YES		Hardware
 tulip		YES		YES		YES		Hardware
diff --git a/Documentation/networking/net-modules.txt b/Documentation/networking/net-modules.txt
index 3830a83513d2..0b27863f155c 100644
--- a/Documentation/networking/net-modules.txt
+++ b/Documentation/networking/net-modules.txt
@@ -284,9 +284,6 @@ ppp.c:
 seeq8005.c: *Not modularized*
 	(Probes ports: 0x300, 0x320, 0x340, 0x360)
 
-sk_g16.c: *Not modularized*
-	(Probes ports: 0x100, 0x180, 0x208, 0x220m 0x288, 0x320, 0x328, 0x390)
-
 skeleton.c: *Skeleton*
 
 slhc.c:
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 3a0a55b62aaf..20bdc12d5f21 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -989,21 +989,6 @@ config EEXPRESS_PRO
 	  <file:Documentation/networking/net-modules.txt>. The module
 	  will be called eepro.
 
-config FMV18X
-	tristate "FMV-181/182/183/184 support (OBSOLETE)"
-	depends on NET_ISA && OBSOLETE
-	---help---
-	  If you have a Fujitsu FMV-181/182/183/184 network (Ethernet) card,
-	  say Y and read the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
-	  If you use an FMV-183 or FMV-184 and it is not working, you may need
-	  to disable Plug & Play mode of the card.
-
-	  To compile this driver as a module, choose M here and read
-	  <file:Documentation/networking/net-modules.txt>. The module
-	  will be called fmv18x.
-
 config HPLAN_PLUS
 	tristate "HP PCLAN+ (27247B and 27252A) support"
 	depends on NET_ISA
@@ -1092,14 +1077,6 @@ config SEEQ8005
 	  <file:Documentation/networking/net-modules.txt>. The module
 	  will be called seeq8005.
 
-config SK_G16
-	tristate "SK_G16 support (OBSOLETE)"
-	depends on NET_ISA && OBSOLETE
-	help
-	  If you have a network (Ethernet) card of this type, say Y and read
-	  the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
 config SKMC
 	tristate "SKnet MCA support"
 	depends on NET_ETHERNET && MCA && BROKEN
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 6202b10dbb4d..b52026109c21 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -73,7 +73,6 @@ obj-$(CONFIG_MAC8390) += mac8390.o 8390.o
 obj-$(CONFIG_APNE) += apne.o 8390.o
 obj-$(CONFIG_PCMCIA_PCNET) += 8390.o
 obj-$(CONFIG_SHAPER) += shaper.o
-obj-$(CONFIG_SK_G16) += sk_g16.o
 obj-$(CONFIG_HP100) += hp100.o
 obj-$(CONFIG_SMC9194) += smc9194.o
 obj-$(CONFIG_FEC) += fec.o
@@ -121,7 +120,6 @@ obj-$(CONFIG_DEFXX) += defxx.o
 obj-$(CONFIG_SGISEEQ) += sgiseeq.o
 obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
 obj-$(CONFIG_AT1700) += at1700.o
-obj-$(CONFIG_FMV18X) += fmv18x.o
 obj-$(CONFIG_EL1) += 3c501.o
 obj-$(CONFIG_EL16) += 3c507.o
 obj-$(CONFIG_ELMC) += 3c523.o
diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index fb433325aa27..3707df6b0cfa 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -210,9 +210,6 @@ static struct devprobe2 isa_probes[] __initdata = {
 #ifdef CONFIG_AT1700
 	{at1700_probe, 0},
 #endif
-#ifdef CONFIG_FMV18X		/* Fujitsu FMV-181/182 */
-	{fmv18x_probe, 0},
-#endif
 #ifdef CONFIG_ETH16I
 	{eth16i_probe, 0},	/* ICL EtherTeam 16i/32 */
 #endif
@@ -243,9 +240,6 @@ static struct devprobe2 isa_probes[] __initdata = {
 #ifdef CONFIG_ELPLUS		/* 3c505 */
 	{elplus_probe, 0},
 #endif
-#ifdef CONFIG_SK_G16
-	{SK_init, 0},
-#endif
 #ifdef CONFIG_NI5010
 	{ni5010_probe, 0},
 #endif
diff --git a/drivers/net/fmv18x.c b/drivers/net/fmv18x.c
deleted file mode 100644
index 04c748523471..000000000000
--- a/drivers/net/fmv18x.c
+++ /dev/null
@@ -1,689 +0,0 @@
-/* fmv18x.c: A network device driver for the Fujitsu FMV-181/182/183/184.
-
-	Original: at1700.c (1993-94 by Donald Becker).
-		Copyright 1993 United States Government as represented by the
-		Director, National Security Agency.
-		The author may be reached as becker@scyld.com, or C/O
-			Scyld Computing Corporation
-			410 Severn Ave., Suite 210
-			Annapolis MD 21403
-
-	Modified by Yutaka TAMIYA (tamy@flab.fujitsu.co.jp)
-		Copyright 1994 Fujitsu Laboratories Ltd.
-	Special thanks to:
-		Masayoshi UTAKA (utaka@ace.yk.fujitsu.co.jp)
-			for testing this driver.
-		H. NEGISHI (agy, negishi@sun45.psd.cs.fujitsu.co.jp)
-			for suggestion of some program modification.
-		Masahiro SEKIGUCHI <seki@sysrap.cs.fujitsu.co.jp>
-			for suggestion of some program modification.
-		Kazutoshi MORIOKA (morioka@aurora.oaks.cs.fujitsu.co.jp)
-			for testing this driver.
-
-	This software may be used and distributed according to the terms
-	of the GNU General Public License, incorporated herein by reference.
-
-	This is a device driver for the Fujitsu FMV-181/182/183/184, which
-	is a straight-forward Fujitsu MB86965 implementation.
-
-  Sources:
-    at1700.c
-    The Fujitsu MB86965 datasheet.
-    The Fujitsu FMV-181/182 user's guide
-*/
-
-static const char version[] =
-	"fmv18x.c:v2.2.0 09/24/98  Yutaka TAMIYA (tamy@flab.fujitsu.co.jp)\n";
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/fcntl.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/in.h>
-#include <linux/slab.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/spinlock.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/delay.h>
-#include <linux/bitops.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/dma.h>
-
-#define DRV_NAME "fmv18x"
-
-static unsigned fmv18x_probe_list[] __initdata = {
-	0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x300, 0x340, 0
-};
-
-/* use 0 for production, 1 for verification, >2 for debug */
-#ifndef NET_DEBUG
-#define NET_DEBUG 1
-#endif
-static unsigned int net_debug = NET_DEBUG;
-
-typedef unsigned char uchar;
-
-/* Information that need to be kept for each board. */
-struct net_local {
-	struct net_device_stats stats;
-	long open_time;				/* Useless example local info. */
-	uint tx_started:1;			/* Number of packet on the Tx queue. */
-	uint tx_queue_ready:1;		/* Tx queue is ready to be sent. */
-	uint rx_started:1;			/* Packets are Rxing. */
-	uchar tx_queue;				/* Number of packet on the Tx queue. */
-	ushort tx_queue_len;		/* Current length of the Tx queue. */
-	spinlock_t lock;
-};
-
-
-/* Offsets from the base address. */
-#define STATUS			0
-#define TX_STATUS		0
-#define RX_STATUS		1
-#define TX_INTR			2		/* Bit-mapped interrupt enable registers. */
-#define RX_INTR			3
-#define TX_MODE			4
-#define RX_MODE			5
-#define CONFIG_0		6		/* Misc. configuration settings. */
-#define CONFIG_1		7
-/* Run-time register bank 2 definitions. */
-#define DATAPORT		8		/* Word-wide DMA or programmed-I/O dataport. */
-#define TX_START		10
-#define COL16CNTL		11		/* Controll Reg for 16 collisions */
-#define MODE13			13
-/* Fujitsu FMV-18x Card Configuration */
-#define	FJ_STATUS0		0x10
-#define	FJ_STATUS1		0x11
-#define	FJ_CONFIG0		0x12
-#define	FJ_CONFIG1		0x13
-#define	FJ_MACADDR		0x14	/* 0x14 - 0x19 */
-#define	FJ_BUFCNTL		0x1A
-#define	FJ_BUFDATA		0x1C
-#define FMV18X_IO_EXTENT	32
-
-/* Index to functions, as function prototypes. */
-
-static int fmv18x_probe1(struct net_device *dev, short ioaddr);
-static int net_open(struct net_device *dev);
-static int net_send_packet(struct sk_buff *skb, struct net_device *dev);
-static irqreturn_t net_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-static void net_rx(struct net_device *dev);
-static void net_timeout(struct net_device *dev);
-static int net_close(struct net_device *dev);
-static struct net_device_stats *net_get_stats(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-
-
-/* Check for a network adaptor of this type, and return '0' iff one exists.
-   If dev->base_addr == 0, probe all likely locations.
-   If dev->base_addr == 1, always return failure.
-   If dev->base_addr == 2, allocate space for the device and return success
-   (detachable devices only).
-   */
-
-static int io = 0x220;
-static int irq;
-
-struct net_device * __init fmv18x_probe(int unit)
-{
-	struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
-	unsigned *port;
-	int err = 0;
-
-	if (!dev)
-		return ERR_PTR(-ENODEV);
-
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-		io = dev->base_addr;
-		irq = dev->irq;
-	}
-
-	SET_MODULE_OWNER(dev);
-
-	if (io > 0x1ff) {	/* Check a single specified location. */
-		err = fmv18x_probe1(dev, io);
-	} else if (io != 0) {	/* Don't probe at all. */
-		err = -ENXIO;
-	} else {
-		for (port = fmv18x_probe_list; *port; port++)
-			if (fmv18x_probe1(dev, *port) == 0)
-				break;
-		if (!*port)
-			err = -ENODEV;
-	}
-	if (err)
-		goto out;
-	err = register_netdev(dev);
-	if (err)
-		goto out1;
-	return dev;
-out1:
-	free_irq(dev->irq, dev);
-	release_region(dev->base_addr, FMV18X_IO_EXTENT);
-out:
-	free_netdev(dev);
-	return ERR_PTR(err);
-}
-
-/* The Fujitsu datasheet suggests that the NIC be probed for by checking its
-   "signature", the default bit pattern after a reset.  This *doesn't* work --
-   there is no way to reset the bus interface without a complete power-cycle!
-
-   It turns out that ATI came to the same conclusion I did: the only thing
-   that can be done is checking a few bits and then diving right into MAC
-   address check. */
-
-static int __init fmv18x_probe1(struct net_device *dev, short ioaddr)
-{
-	char irqmap[4] = {3, 7, 10, 15};
-	char irqmap_pnp[8] = {3, 4, 5, 7, 9, 10, 11, 15};
-	unsigned int i, retval;
-	struct net_local *lp;
-
-	/* Resetting the chip doesn't reset the ISA interface, so don't bother.
-	   That means we have to be careful with the register values we probe for.
-	   */
-
-	if (!request_region(ioaddr, FMV18X_IO_EXTENT, DRV_NAME))
-		return -EBUSY;
-
-	dev->irq = irq;
-	dev->base_addr = ioaddr;
-
-	/* Check I/O address configuration and Fujitsu vendor code */
-	if (inb(ioaddr+FJ_MACADDR  ) != 0x00
-	||  inb(ioaddr+FJ_MACADDR+1) != 0x00
-	||  inb(ioaddr+FJ_MACADDR+2) != 0x0e) {
-		retval = -ENODEV;
-		goto out;
-	}
-
-	/* Check PnP mode for FMV-183/184/183A/184A. */
-	/* This PnP routine is very poor. IO and IRQ should be known. */
-	if (inb(ioaddr + FJ_STATUS1) & 0x20) {
-		for (i = 0; i < 8; i++) {
-			if (dev->irq == irqmap_pnp[i])
-				break;
-		}
-		if (i == 8) {
-			retval = -ENODEV;
-			goto out;
-		}
-	} else {
-		if (fmv18x_probe_list[inb(ioaddr + FJ_CONFIG0) & 0x07] != ioaddr)
-			return -ENODEV;
-		dev->irq = irqmap[(inb(ioaddr + FJ_CONFIG0)>>6) & 0x03];
-	}
-
-	/* Snarf the interrupt vector now. */
-	retval = request_irq(dev->irq, &net_interrupt, 0, DRV_NAME, dev);
-	if (retval) {
-		printk ("FMV-18x found at %#3x, but it's unusable due to a conflict on"
-				"IRQ %d.\n", ioaddr, dev->irq);
-		goto out;
-	}
-
-	printk("%s: FMV-18x found at %#3x, IRQ %d, address ", dev->name,
-		   ioaddr, dev->irq);
-
-	for(i = 0; i < 6; i++) {
-		unsigned char val = inb(ioaddr + FJ_MACADDR + i);
-		printk("%02x", val);
-		dev->dev_addr[i] = val;
-	}
-
-	/* "FJ_STATUS0" 12 bit 0x0400 means use regular 100 ohm 10baseT signals,
-	   rather than 150 ohm shielded twisted pair compensation.
-	   0x0000 == auto-sense the interface
-	   0x0800 == use TP interface
-	   0x1800 == use coax interface
-	   */
-	{
-		const char *porttype[] = {"auto-sense", "10baseT", "auto-sense", "10base2/5"};
-		ushort setup_value = inb(ioaddr + FJ_STATUS0);
-
-		switch( setup_value & 0x07 ){
-		case 0x01 /* 10base5 */:
-		case 0x02 /* 10base2 */: dev->if_port = 0x18; break;
-		case 0x04 /* 10baseT */: dev->if_port = 0x08; break;
-		default /* auto-sense*/: dev->if_port = 0x00; break;
-		}
-		printk(" %s interface.\n", porttype[(dev->if_port>>3) & 3]);
-	}
-
-	/* Initialize LAN Controller and LAN Card */
-	outb(0xda, ioaddr + CONFIG_0);	 /* Initialize LAN Controller */
-	outb(0x00, ioaddr + CONFIG_1);	 /* Stand by mode */
-	outb(0x00, ioaddr + FJ_CONFIG1); /* Disable IRQ of LAN Card */
-	outb(0x00, ioaddr + FJ_BUFCNTL); /* Reset ? I'm not sure (TAMIYA) */
-
-	/* wait for a while */
-	udelay(200);
-
-	/* Set the station address in bank zero. */
-	outb(0x00, ioaddr + CONFIG_1);
-	for (i = 0; i < 6; i++)
-		outb(dev->dev_addr[i], ioaddr + 8 + i);
-
-	/* Switch to bank 1 and set the multicast table to accept none. */
-	outb(0x04, ioaddr + CONFIG_1);
-	for (i = 0; i < 8; i++)
-		outb(0x00, ioaddr + 8 + i);
-
-	/* Switch to bank 2 and lock our I/O address. */
-	outb(0x08, ioaddr + CONFIG_1);
-	outb(dev->if_port, ioaddr + MODE13);
-	outb(0x00, ioaddr + COL16CNTL);
-
-	if (net_debug)
-		printk(version);
-
-	/* Initialize the device structure. */
-	dev->priv = kmalloc(sizeof(struct net_local), GFP_KERNEL);
-	if (!dev->priv) {
-		retval = -ENOMEM;
-		goto out_irq;
-	}
-	memset(dev->priv, 0, sizeof(struct net_local));
-	lp = dev->priv;
-	spin_lock_init(&lp->lock);
-
-	dev->open		= net_open;
-	dev->stop		= net_close;
-	dev->hard_start_xmit	= net_send_packet;
-	dev->tx_timeout		= net_timeout;
-	dev->watchdog_timeo	= HZ/10;
-	dev->get_stats		= net_get_stats;
-	dev->set_multicast_list = set_multicast_list;
-	return 0;
-
-out_irq:
-	free_irq(dev->irq, dev);
-out:
-	release_region(ioaddr, FMV18X_IO_EXTENT);
-	return retval;
-}
-
-
-static int net_open(struct net_device *dev)
-{
-	struct net_local *lp = dev->priv;
-	int ioaddr = dev->base_addr;
-
-	/* Set the configuration register 0 to 32K 100ns. byte-wide memory,
-	   16 bit bus access, and two 4K Tx, enable the Rx and Tx. */
-	outb(0x5a, ioaddr + CONFIG_0);
-
-	/* Powerup and switch to register bank 2 for the run-time registers. */
-	outb(0xe8, ioaddr + CONFIG_1);
-
-	lp->tx_started = 0;
-	lp->tx_queue_ready = 1;
-	lp->rx_started = 0;
-	lp->tx_queue = 0;
-	lp->tx_queue_len = 0;
-
-	/* Clear Tx and Rx Status */
-	outb(0xff, ioaddr + TX_STATUS);
-	outb(0xff, ioaddr + RX_STATUS);
-	lp->open_time = jiffies;
-
-	netif_start_queue(dev);
-	
-	/* Enable the IRQ of the LAN Card */
-	outb(0x80, ioaddr + FJ_CONFIG1);
-
-	/* Enable both Tx and Rx interrupts */
-	outw(0x8182, ioaddr+TX_INTR);
-
-	return 0;
-}
-
-static void net_timeout(struct net_device *dev)
-{
-	struct net_local *lp = dev->priv;
-	int ioaddr = dev->base_addr;
-	unsigned long flags;
-	
-	
-	printk(KERN_WARNING "%s: transmit timed out with status %04x, %s?\n", dev->name,
-		   htons(inw(ioaddr + TX_STATUS)),
-		   inb(ioaddr + TX_STATUS) & 0x80
-		   ? "IRQ conflict" : "network cable problem");
-	printk(KERN_WARNING "%s: timeout registers: %04x %04x %04x %04x %04x %04x %04x %04x.\n",
-		   dev->name, htons(inw(ioaddr + 0)),
-		   htons(inw(ioaddr + 2)), htons(inw(ioaddr + 4)),
-		   htons(inw(ioaddr + 6)), htons(inw(ioaddr + 8)),
-		   htons(inw(ioaddr +10)), htons(inw(ioaddr +12)),
-		   htons(inw(ioaddr +14)));
-	printk(KERN_WARNING "eth card: %04x %04x\n",
-		htons(inw(ioaddr+FJ_STATUS0)),
-		htons(inw(ioaddr+FJ_CONFIG0)));
-	lp->stats.tx_errors++;
-	/* ToDo: We should try to restart the adaptor... */
-	spin_lock_irqsave(&lp->lock, flags);
-
-	/* Initialize LAN Controller and LAN Card */
-	outb(0xda, ioaddr + CONFIG_0);   /* Initialize LAN Controller */
-	outb(0x00, ioaddr + CONFIG_1);   /* Stand by mode */
-	outb(0x00, ioaddr + FJ_CONFIG1); /* Disable IRQ of LAN Card */
-	outb(0x00, ioaddr + FJ_BUFCNTL); /* Reset ? I'm not sure */
-	net_open(dev);
-	spin_unlock_irqrestore(&lp->lock, flags);
-
-	netif_wake_queue(dev);
-}
-
-static int net_send_packet(struct sk_buff *skb, struct net_device *dev)
-{
-	struct net_local *lp = dev->priv;
-	int ioaddr = dev->base_addr;
-	short length = skb->len;
-	unsigned char *buf;
-	unsigned long flags;
-
-	/* Block a transmit from overlapping.  */
-	
-	if (length > ETH_FRAME_LEN) {
-		if (net_debug)
-			printk("%s: Attempting to send a large packet (%d bytes).\n",
-				dev->name, length);
-		return 1;
-	}
-	
-	if (length < ETH_ZLEN) {
-		skb = skb_padto(skb, ETH_ZLEN);
-		if (skb == NULL)
-			return 0;
-		length = ETH_ZLEN;
-	}
-	buf = skb->data;
-	
-	if (net_debug > 4)
-		printk("%s: Transmitting a packet of length %lu.\n", dev->name,
-			   (unsigned long)skb->len);
-	/* We may not start transmitting unless we finish transferring
-	   a packet into the Tx queue. During executing the following
-	   codes we possibly catch a Tx interrupt. Thus we flag off
-	   tx_queue_ready, so that we prevent the interrupt routine
-	   (net_interrupt) to start transmitting. */
-	spin_lock_irqsave(&lp->lock, flags);
-	lp->tx_queue_ready = 0;
-	{
-		outw(length, ioaddr + DATAPORT);
-		outsw(ioaddr + DATAPORT, buf, (length + 1) >> 1);
-		lp->tx_queue++;
-		lp->tx_queue_len += length + 2;
-	}
-	lp->tx_queue_ready = 1;
-	spin_unlock_irqrestore(&lp->lock, flags);
-
-	if (lp->tx_started == 0) {
-		/* If the Tx is idle, always trigger a transmit. */
-		outb(0x80 | lp->tx_queue, ioaddr + TX_START);
-		lp->tx_queue = 0;
-		lp->tx_queue_len = 0;
-		dev->trans_start = jiffies;
-		lp->tx_started = 1;
-	} else if (lp->tx_queue_len >= 4096 - 1502) /* No room for a packet */
-		netif_stop_queue(dev);
-
-	dev_kfree_skb(skb);
-	return 0;
-}
-
-/* The typical workload of the driver:
-   Handle the network interface interrupts. */
-static irqreturn_t
-net_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
-	struct net_device *dev = dev_id;
-	struct net_local *lp;
-	int ioaddr, status;
-
-	ioaddr = dev->base_addr;
-	lp = dev->priv;
-	status = inw(ioaddr + TX_STATUS);
-	outw(status, ioaddr + TX_STATUS);
-
-	if (net_debug > 4)
-		printk("%s: Interrupt with status %04x.\n", dev->name, status);
-	if (lp->rx_started == 0 &&
-		(status & 0xff00 || (inb(ioaddr + RX_MODE) & 0x40) == 0)) {
-		/* Got a packet(s).
-		   We cannot execute net_rx more than once at the same time for
-		   the same device. During executing net_rx, we possibly catch a
-		   Tx interrupt. Thus we flag on rx_started, so that we prevent
-		   the interrupt routine (net_interrupt) to dive into net_rx
-		   again. */
-		lp->rx_started = 1;
-		outb(0x00, ioaddr + RX_INTR);	/* Disable RX intr. */
-		net_rx(dev);
-		outb(0x81, ioaddr + RX_INTR);	/* Enable  RX intr. */
-		lp->rx_started = 0;
-	}
-	if (status & 0x00ff) {
-		if (status & 0x02) {
-			/* More than 16 collisions occurred */
-			if (net_debug > 4)
-				printk("%s: 16 Collision occur during Txing.\n", dev->name);
-			/* Cancel sending a packet. */
-			outb(0x03, ioaddr + COL16CNTL);
-			lp->stats.collisions++;
-		}
-		if (status & 0x82) {
-			spin_lock(&lp->lock);
-			lp->stats.tx_packets++;
-			if (lp->tx_queue && lp->tx_queue_ready) {
-				outb(0x80 | lp->tx_queue, ioaddr + TX_START);
-				lp->tx_queue = 0;
-				lp->tx_queue_len = 0;
-				dev->trans_start = jiffies;
-				netif_wake_queue(dev);	/* Inform upper layers. */
-			} else {
-				lp->tx_started = 0;
-				netif_wake_queue(dev);	/* Inform upper layers. */
-			}
-			spin_unlock(&lp->lock);
-		}
-	}
-	return IRQ_RETVAL(status);
-}
-
-/* We have a good packet(s), get it/them out of the buffers. */
-static void net_rx(struct net_device *dev)
-{
-	struct net_local *lp = dev->priv;
-	int ioaddr = dev->base_addr;
-	int boguscount = 5;
-
-	while ((inb(ioaddr + RX_MODE) & 0x40) == 0) {
-		/* Clear PKT_RDY bit: by agy 19940922 */
-		/* outb(0x80, ioaddr + RX_STATUS); */
-		ushort status = inw(ioaddr + DATAPORT);
-
-		if (net_debug > 4)
-			printk("%s: Rxing packet mode %02x status %04x.\n",
-				   dev->name, inb(ioaddr + RX_MODE), status);
-#ifndef final_version
-		if (status == 0) {
-			outb(0x05, ioaddr + 14);
-			break;
-		}
-#endif
-
-		if ((status & 0xF0) != 0x20) {	/* There was an error. */
-			lp->stats.rx_errors++;
-			if (status & 0x08) lp->stats.rx_length_errors++;
-			if (status & 0x04) lp->stats.rx_frame_errors++;
-			if (status & 0x02) lp->stats.rx_crc_errors++;
-			if (status & 0x01) lp->stats.rx_over_errors++;
-		} else {
-			ushort pkt_len = inw(ioaddr + DATAPORT);
-			/* Malloc up new buffer. */
-			struct sk_buff *skb;
-
-			if (pkt_len > 1550) {
-				printk("%s: The FMV-18x claimed a very large packet, size %d.\n",
-					   dev->name, pkt_len);
-				outb(0x05, ioaddr + 14);
-				lp->stats.rx_errors++;
-				break;
-			}
-			skb = dev_alloc_skb(pkt_len+3);
-			if (skb == NULL) {
-				printk("%s: Memory squeeze, dropping packet (len %d).\n",
-					   dev->name, pkt_len);
-				outb(0x05, ioaddr + 14);
-				lp->stats.rx_dropped++;
-				break;
-			}
-			skb->dev = dev;
-			skb_reserve(skb,2);
-
-			insw(ioaddr + DATAPORT, skb_put(skb,pkt_len), (pkt_len + 1) >> 1);
-
-			if (net_debug > 5) {
-				int i;
-				printk("%s: Rxed packet of length %d: ", dev->name, pkt_len);
-				for (i = 0; i < 14; i++)
-					printk(" %02x", skb->data[i]);
-				printk(".\n");
-			}
-
-			skb->protocol=eth_type_trans(skb, dev);
-			netif_rx(skb);
-			dev->last_rx = jiffies;
-			lp->stats.rx_packets++;
-			lp->stats.rx_bytes += pkt_len;
-		}
-		if (--boguscount <= 0)
-			break;
-	}
-
-	/* If any worth-while packets have been received, dev_rint()
-	   has done a mark_bh(NET_BH) for us and will work on them
-	   when we get to the bottom-half routine. */
-	{
-		int i;
-		for (i = 0; i < 20; i++) {
-			if ((inb(ioaddr + RX_MODE) & 0x40) == 0x40)
-				break;
-			(void)inw(ioaddr + DATAPORT);				/* dummy status read */
-			outb(0x05, ioaddr + 14);
-		}
-
-		if (net_debug > 5 && i > 0)
-			printk("%s: Exint Rx packet with mode %02x after %d ticks.\n",
-				   dev->name, inb(ioaddr + RX_MODE), i);
-	}
-
-	return;
-}
-
-/* The inverse routine to net_open(). */
-static int net_close(struct net_device *dev)
-{
-	int ioaddr = dev->base_addr;
-
-	((struct net_local *)dev->priv)->open_time = 0;
-
-	netif_stop_queue(dev);
-	
-	/* Set configuration register 0 to disable Tx and Rx. */
-	outb(0xda, ioaddr + CONFIG_0);
-
-	/* Update the statistics -- ToDo. */
-
-	/* Power-down the chip.  Green, green, green! */
-	outb(0x00, ioaddr + CONFIG_1);
-
-	/* Set the ethernet adaptor disable IRQ */
-	outb(0x00, ioaddr + FJ_CONFIG1);
-
-	return 0;
-}
-
-/* Get the current statistics.	This may be called with the card open or
-   closed. */
-static struct net_device_stats *net_get_stats(struct net_device *dev)
-{
-	struct net_local *lp = dev->priv;
-	return &lp->stats;
-}
-
-/* Set or clear the multicast filter for this adaptor.
-   num_addrs == -1	Promiscuous mode, receive all packets
-   num_addrs == 0	Normal mode, clear multicast list
-   num_addrs > 0	Multicast mode, receive normal and MC packets, and do
-			best-effort filtering.
- */
- 
-static void set_multicast_list(struct net_device *dev)
-{
-	short ioaddr = dev->base_addr;
-	if (dev->mc_count || dev->flags&(IFF_PROMISC|IFF_ALLMULTI))
-	{
-		/*
-		 *	We must make the kernel realise we had to move
-		 *	into promisc mode or we start all out war on
-		 *	the cable. - AC
-		 */
-		dev->flags|=IFF_PROMISC;
-
-		outb(3, ioaddr + RX_MODE);	/* Enable promiscuous mode */
-	}
-	else
-		outb(2, ioaddr + RX_MODE);	/* Disable promiscuous, use normal mode */
-}
-
-#ifdef MODULE
-static struct net_device *dev_fmv18x;
-
-MODULE_PARM(io, "i");
-MODULE_PARM(irq, "i");
-MODULE_PARM(net_debug, "i");
-MODULE_PARM_DESC(io, "FMV-18X I/O address");
-MODULE_PARM_DESC(irq, "FMV-18X IRQ number");
-MODULE_PARM_DESC(net_debug, "FMV-18X debug level (0-1,5-6)");
-MODULE_LICENSE("GPL");
-
-int init_module(void)
-{
-	if (io == 0)
-		printk("fmv18x: You should not use auto-probing with insmod!\n");
-	dev_fmv18x = fmv18x_probe(-1);
-	if (IS_ERR(dev_fmv18x))
-		return PTR_ERR(dev_fmv18x);
-	return 0;
-}
-
-void
-cleanup_module(void)
-{
-	unregister_netdev(dev_fmv18x);
-	free_irq(dev_fmv18x->irq, dev_fmv18x);
-	release_region(dev_fmv18x->base_addr, FMV18X_IO_EXTENT);
-	free_netdev(dev_fmv18x);
-}
-#endif /* MODULE */
-
-/*
- * Local variables:
- *  compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c fmv18x.c"
- *  version-control: t
- *  kept-new-versions: 5
- *  tab-width: 4
- *  c-indent-level: 4
- * End:
- */
diff --git a/drivers/net/sk_g16.c b/drivers/net/sk_g16.c
deleted file mode 100644
index 134ae0e6495b..000000000000
--- a/drivers/net/sk_g16.c
+++ /dev/null
@@ -1,2066 +0,0 @@
-/*-
- * Copyright (C) 1994 by PJD Weichmann & SWS Bern, Switzerland
- *
- * This software may be used and distributed according to the terms
- * of the GNU General Public License, incorporated herein by reference.
- *
- * Module         : sk_g16.c
- *
- * Version        : $Revision: 1.1 $
- *
- * Author         : Patrick J.D. Weichmann
- *
- * Date Created   : 94/05/26
- * Last Updated   : $Date: 1994/06/30 16:25:15 $
- *
- * Description    : Schneider & Koch G16 Ethernet Device Driver for
- *                  Linux Kernel >= 1.1.22
- * Update History :
- *                  Paul Gortmaker, 03/97: Fix for v2.1.x to use read{b,w}
- *                  write{b,w} and memcpy -> memcpy_{to,from}io
- *
- *		    Jeff Garzik, 06/2000, Modularize
- *
--*/
-
-static const char rcsid[] = "$Id: sk_g16.c,v 1.1 1994/06/30 16:25:15 root Exp $";
-
-/*
- * The Schneider & Koch (SK) G16 Network device driver is based
- * on the 'ni6510' driver from Michael Hipp which can be found at
- * ftp://sunsite.unc.edu/pub/Linux/system/Network/drivers/nidrivers.tar.gz
- * 
- * Sources: 1) ni6510.c by M. Hipp
- *          2) depca.c  by D.C. Davies
- *          3) skeleton.c by D. Becker
- *          4) Am7990 Local Area Network Controller for Ethernet (LANCE),
- *             AMD, Pub. #05698, June 1989
- *
- * Many Thanks for helping me to get things working to: 
- *                 
- *                 A. Cox (A.Cox@swansea.ac.uk)
- *                 M. Hipp (mhipp@student.uni-tuebingen.de)
- *                 R. Bolz (Schneider & Koch, Germany)
- *
- * To Do: 
- *        - Support of SK_G8 and other SK Network Cards.
- *        - Autoset memory mapped RAM. Check for free memory and then
- *          configure RAM correctly. 
- *        - SK_close should really set card in to initial state.
- *        - Test if IRQ 3 is not switched off. Use autoirq() functionality.
- *          (as in /drivers/net/skeleton.c)
- *        - Implement Multicast addressing. At minimum something like
- *          in depca.c. 
- *        - Redo the statistics part.
- *        - Try to find out if the board is in 8 Bit or 16 Bit slot.
- *          If in 8 Bit mode don't use IRQ 11.
- *        - (Try to make it slightly faster.) 
- *	  - Power management support
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/fcntl.h>
-#include <linux/ioport.h>
-#include <linux/interrupt.h>
-#include <linux/slab.h>
-#include <linux/string.h> 
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/bitops.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-
-#include "sk_g16.h"
-
-/* 
- * Schneider & Koch Card Definitions 
- * =================================
- */  
-
-#define SK_NAME   "SK_G16"
-
-/*
- * SK_G16 Configuration
- * --------------------
- */ 
-
-/* 
- * Abbreviations
- * -------------
- *  
- * RAM - used for the 16KB shared memory 
- * Boot_ROM, ROM - are used for referencing the BootEPROM
- *
- * SK_BOOT_ROM and SK_ADDR are symbolic constants used to configure
- * the behaviour of the driver and the SK_G16.
- *
- * ! See sk_g16.install on how to install and configure the driver !   
- *
- * SK_BOOT_ROM defines if the Boot_ROM should be switched off or not.
- *
- * SK_ADDR defines the address where the RAM will be mapped into the real
- *         host memory.
- *         valid addresses are from 0xa0000 to 0xfc000 in 16Kbyte steps.
- */  
- 
-#define SK_BOOT_ROM     1              /* 1=BootROM on 0=off */
-
-#define SK_ADDR         0xcc000
-
-/* 
- * In POS3 are bits A14-A19 of the address bus. These bits can be set
- * to choose the RAM address. That's why we only can choose the RAM address
- * in 16KB steps.
- */
-
-#define POS_ADDR       (rom_addr>>14)  /* Do not change this line */
-
-/* 
- * SK_G16 I/O PORT's + IRQ's + Boot_ROM locations
- * ----------------------------------------------
- */
-
-/* 
- * As nearly every card has also SK_G16 a specified I/O Port region and
- * only a few possible IRQ's.
- * In the Installation Guide from Schneider & Koch is listed a possible
- * Interrupt IRQ2. IRQ2 is always IRQ9 in boards with two cascaded interrupt
- * controllers. So we use in SK_IRQS IRQ9.
- */
-
-/* Don't touch any of the following #defines. */
-
-#define SK_IO_PORTS     { 0x100, 0x180, 0x208, 0x220, 0x288, 0x320, 0x328, 0x390, 0 }
-
-#define SK_IRQS         { 3, 5, 9, 11, 0 }
-
-#define SK_BOOT_ROM_LOCATIONS { 0xc0000, 0xc4000, 0xc8000, 0xcc000, 0xd0000, 0xd4000, 0xd8000, 0xdc000, 0 }
-
-#define SK_BOOT_ROM_ID  { 0x55, 0xaa, 0x10, 0x50, 0x06, 0x33 }
-
-/* 
- * SK_G16 POS REGISTERS 
- * --------------------
- */
-
-/*
- * SK_G16 has a Programmable Option Select (POS) Register.
- * The POS is composed of 8 separate registers (POS0-7) which 
- * are I/O mapped on an address set by the W1 switch.                    
- *
- */
-
-#define SK_POS_SIZE 8           /* 8 I/O Ports are used by SK_G16 */
-
-#define SK_POS0     ioaddr      /* Card-ID Low (R) */
-#define SK_POS1     ioaddr+1    /* Card-ID High (R) */
-#define SK_POS2     ioaddr+2    /* Card-Enable, Boot-ROM Disable (RW) */
-#define SK_POS3     ioaddr+3    /* Base address of RAM */
-#define SK_POS4     ioaddr+4    /* IRQ */
-
-/* POS5 - POS7 are unused */
-
-/* 
- * SK_G16 MAC PREFIX 
- * -----------------
- */
-
-/* 
- * Scheider & Koch manufacturer code (00:00:a5).
- * This must be checked, that we are sure it is a SK card.
- */
-
-#define SK_MAC0         0x00
-#define SK_MAC1         0x00
-#define SK_MAC2         0x5a
-
-/* 
- * SK_G16 ID 
- * ---------
- */ 
-
-/* 
- * If POS0,POS1 contain the following ID, then we know
- * at which I/O Port Address we are. 
- */
-
-#define SK_IDLOW  0xfd 
-#define SK_IDHIGH 0x6a
-
-
-/* 
- * LANCE POS Bit definitions 
- * -------------------------
- */
-
-#define SK_ROM_RAM_ON  (POS2_CARD)
-#define SK_ROM_RAM_OFF (POS2_EPROM)
-#define SK_ROM_ON      (inb(SK_POS2) & POS2_CARD)
-#define SK_ROM_OFF     (inb(SK_POS2) | POS2_EPROM)
-#define SK_RAM_ON      (inb(SK_POS2) | POS2_CARD)
-#define SK_RAM_OFF     (inb(SK_POS2) & POS2_EPROM) 
-
-#define POS2_CARD  0x0001              /* 1 = SK_G16 on      0 = off */
-#define POS2_EPROM 0x0002              /* 1 = Boot EPROM off 0 = on */ 
-
-/* 
- * SK_G16 Memory mapped Registers
- * ------------------------------
- *
- */ 
-
-#define SK_IOREG        (&board->ioreg) /* LANCE data registers.     */ 
-#define SK_PORT         (&board->port)  /* Control, Status register  */
-#define SK_IOCOM        (&board->iocom) /* I/O Command               */
-
-/* 
- * SK_G16 Status/Control Register bits
- * -----------------------------------
- *
- * (C) Controlreg (S) Statusreg 
- */
-
-/* 
- * Register transfer: 0 = no transfer
- *                    1 = transferring data between LANCE and I/O reg 
- */
-#define SK_IORUN        0x20   
-
-/* 
- * LANCE interrupt: 0 = LANCE interrupt occurred	
- *                  1 = no LANCE interrupt occurred
- */
-#define SK_IRQ          0x10   
-			
-#define SK_RESET        0x08   /* Reset SK_CARD: 0 = RESET 1 = normal */
-#define SK_RW           0x02   /* 0 = write to 1 = read from */
-#define SK_ADR          0x01   /* 0 = REG DataPort 1 = RAP Reg addr port */
-
-  
-#define SK_RREG         SK_RW  /* Transferdirection to read from lance */
-#define SK_WREG         0      /* Transferdirection to write to lance */
-#define SK_RAP          SK_ADR /* Destination Register RAP */
-#define SK_RDATA        0      /* Destination Register REG DataPort */
-
-/* 
- * SK_G16 I/O Command 
- * ------------------
- */
-
-/* 
- * Any bitcombination sets the internal I/O bit (transfer will start) 
- * when written to I/O Command
- */
-
-#define SK_DOIO         0x80   /* Do Transfer */ 
- 
-/* 
- * LANCE RAP (Register Address Port). 
- * ---------------------------------
- */
-
-/*   
- * The LANCE internal registers are selected through the RAP. 
- * The Registers are:
- *
- * CSR0 - Status and Control flags 
- * CSR1 - Low order bits of initialize block (bits 15:00)
- * CSR2 - High order bits of initialize block (bits 07:00, 15:08 are reserved)
- * CSR3 - Allows redefinition of the Bus Master Interface.
- *        This register must be set to 0x0002, which means BSWAP = 0,
- *        ACON = 1, BCON = 0;
- *
- */
- 
-#define CSR0            0x00   
-#define CSR1            0x01  
-#define CSR2            0x02 
-#define CSR3            0x03
-
-/* 
- * General Definitions 
- * ===================
- */
-
-/* 
- * Set the number of Tx and Rx buffers, using Log_2(# buffers).
- * We have 16KB RAM which can be accessed by the LANCE. In the 
- * memory are not only the buffers but also the ring descriptors and
- * the initialize block. 
- * Don't change anything unless you really know what you do.
- */
-
-#define LC_LOG_TX_BUFFERS 1               /* (2 == 2^^1) 2 Transmit buffers */
-#define LC_LOG_RX_BUFFERS 3               /* (8 == 2^^3) 8 Receive buffers */
-
-/* Descriptor ring sizes */
-
-#define TMDNUM (1 << (LC_LOG_TX_BUFFERS)) /* 2 Transmit descriptor rings */
-#define RMDNUM (1 << (LC_LOG_RX_BUFFERS)) /* 8 Receive Buffers */
-
-/* Define Mask for setting RMD, TMD length in the LANCE init_block */
-
-#define TMDNUMMASK (LC_LOG_TX_BUFFERS << 29)
-#define RMDNUMMASK (LC_LOG_RX_BUFFERS << 29)
-
-/*
- * Data Buffer size is set to maximum packet length.
- */
-
-#define PKT_BUF_SZ              1518 
-
-/* 
- * The number of low I/O ports used by the ethercard. 
- */
-
-#define ETHERCARD_TOTAL_SIZE    SK_POS_SIZE
-
-/* 
- * SK_DEBUG
- *
- * Here you can choose what level of debugging wanted.
- *
- * If SK_DEBUG and SK_DEBUG2 are undefined, then only the
- *  necessary messages will be printed.
- *
- * If SK_DEBUG is defined, there will be many debugging prints
- *  which can help to find some mistakes in configuration or even
- *  in the driver code.
- *
- * If SK_DEBUG2 is defined, many many messages will be printed 
- *  which normally you don't need. I used this to check the interrupt
- *  routine. 
- *
- * (If you define only SK_DEBUG2 then only the messages for 
- *  checking interrupts will be printed!)
- *
- * Normal way of live is: 
- *
- * For the whole thing get going let both symbolic constants
- * undefined. If you face any problems and you know what's going
- * on (you know something about the card and you can interpret some
- * hex LANCE register output) then define SK_DEBUG
- * 
- */
-
-#undef  SK_DEBUG	/* debugging */
-#undef  SK_DEBUG2	/* debugging with more verbose report */
-
-#ifdef SK_DEBUG
-#define PRINTK(x) printk x
-#else
-#define PRINTK(x) /**/
-#endif
-
-#ifdef SK_DEBUG2
-#define PRINTK2(x) printk x
-#else
-#define PRINTK2(x) /**/
-#endif
-
-/* 
- * SK_G16 RAM
- *
- * The components are memory mapped and can be set in a region from
- * 0x00000 through 0xfc000 in 16KB steps. 
- *
- * The Network components are: dual ported RAM, Prom, I/O Reg, Status-,
- * Controlregister and I/O Command.
- *
- * dual ported RAM: This is the only memory region which the LANCE chip
- *      has access to. From the Lance it is addressed from 0x0000 to
- *      0x3fbf. The host accesses it normally.
- *
- * PROM: The PROM obtains the ETHERNET-MAC-Address. It is realised as a
- *       8-Bit PROM, this means only the 16 even addresses are used of the
- *       32 Byte Address region. Access to an odd address results in invalid
- *       data.
- * 
- * LANCE I/O Reg: The I/O Reg is build of 4 single Registers, Low-Byte Write,
- *       Hi-Byte Write, Low-Byte Read, Hi-Byte Read.
- *       Transfer from or to the LANCE is always in 16Bit so Low and High
- *       registers are always relevant.
- *
- *       The Data from the Readregister is not the data in the Writeregister!!
- *       
- * Port: Status- and Controlregister. 
- *       Two different registers which share the same address, Status is 
- *       read-only, Control is write-only.
- *    
- * I/O Command: 
- *       Any bitcombination written in here starts the transmission between
- *       Host and LANCE.
- */
-
-typedef struct
-{
-	unsigned char  ram[0x3fc0];   /* 16KB dual ported ram */
-	unsigned char  rom[0x0020];   /* 32Byte PROM containing 6Byte MAC */
-	unsigned char  res1[0x0010];  /* reserved */
-	unsigned volatile short ioreg;/* LANCE I/O Register */
-	unsigned volatile char  port; /* Statusregister and Controlregister */
-	unsigned char  iocom;         /* I/O Command Register */
-} SK_RAM;
-
-/* struct  */
-
-/* 
- * This is the structure for the dual ported ram. We
- * have exactly 16 320 Bytes. In here there must be:
- *
- *     - Initialize Block   (starting at a word boundary)
- *     - Receive and Transmit Descriptor Rings (quadword boundary)
- *     - Data Buffers (arbitrary boundary)
- *
- * This is because LANCE has on SK_G16 only access to the dual ported
- * RAM and nowhere else.
- */
-
-struct SK_ram
-{
-    struct init_block ib;
-    struct tmd tmde[TMDNUM];
-    struct rmd rmde[RMDNUM];
-    char tmdbuf[TMDNUM][PKT_BUF_SZ];
-    char rmdbuf[RMDNUM][PKT_BUF_SZ];
-};
-
-/* 
- * Structure where all necessary information is for ring buffer 
- * management and statistics.
- */
-
-struct priv
-{
-    struct SK_ram *ram;  /* dual ported ram structure */
-    struct rmd *rmdhead; /* start of receive ring descriptors */
-    struct tmd *tmdhead; /* start of transmit ring descriptors */
-    int        rmdnum;   /* actual used ring descriptor */
-    int        tmdnum;   /* actual transmit descriptor for transmitting data */
-    int        tmdlast;  /* last sent descriptor used for error handling, etc */
-    void       *rmdbufs[RMDNUM]; /* pointer to the receive buffers */
-    void       *tmdbufs[TMDNUM]; /* pointer to the transmit buffers */
-    struct net_device_stats stats; /* Device driver statistics */
-};
-
-/* global variable declaration */
-
-/* IRQ map used to reserve a IRQ (see SK_open()) */
-
-/* static variables */
-
-static SK_RAM *board;  /* pointer to our memory mapped board components */
-static DEFINE_SPINLOCK(SK_lock);
-
-/* Macros */
-
-
-/* Function Prototypes */
-
-/*
- * Device Driver functions
- * -----------------------
- * See for short explanation of each function its definitions header.
- */
-
-static int   SK_probe(struct net_device *dev, short ioaddr);
-
-static void  SK_timeout(struct net_device *dev);
-static int   SK_open(struct net_device *dev);
-static int   SK_send_packet(struct sk_buff *skb, struct net_device *dev);
-static irqreturn_t SK_interrupt(int irq, void *dev_id, struct pt_regs * regs);
-static void  SK_rxintr(struct net_device *dev);
-static void  SK_txintr(struct net_device *dev);
-static int   SK_close(struct net_device *dev);
-
-static struct net_device_stats *SK_get_stats(struct net_device *dev);
-
-unsigned int SK_rom_addr(void);
-
-static void set_multicast_list(struct net_device *dev);
-
-/*
- * LANCE Functions
- * ---------------
- */
-
-static int SK_lance_init(struct net_device *dev, unsigned short mode);
-void   SK_reset_board(void);
-void   SK_set_RAP(int reg_number);
-int    SK_read_reg(int reg_number);
-int    SK_rread_reg(void);
-void   SK_write_reg(int reg_number, int value);
-
-/* 
- * Debugging functions
- * -------------------
- */
-
-void SK_print_pos(struct net_device *dev, char *text);
-void SK_print_dev(struct net_device *dev, char *text);
-void SK_print_ram(struct net_device *dev);
-
-
-/*-
- * Function       : SK_init
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : Check for a SK_G16 network adaptor and initialize it.
- *                  This function gets called by dev_init which initializes
- *                  all Network devices.
- *
- * Parameters     : I : struct net_device *dev - structure preconfigured 
- *                                           from Space.c
- * Return Value   : 0 = Driver Found and initialized 
- * Errors         : ENODEV - no device found
- *                  ENXIO  - not probed
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static int io;	/* 0 == probe */
-
-/* 
- * Check for a network adaptor of this type, and return '0' if one exists.
- * If dev->base_addr == 0, probe all likely locations.
- * If dev->base_addr == 1, always return failure.
- */
-
-struct net_device * __init SK_init(int unit)
-{
-	int *port, ports[] = SK_IO_PORTS;  /* SK_G16 supported ports */
-	static unsigned version_printed;
-	struct net_device *dev = alloc_etherdev(sizeof(struct priv));
-	int err = -ENODEV;
-
-	if (!dev)
-		return ERR_PTR(-ENOMEM);
-
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-		io = dev->base_addr;
-	}
-
-	if (version_printed++ == 0)
-	        PRINTK(("%s: %s", SK_NAME, rcsid));
-
-	if (io > 0xff) {        /* Check a single specified address */
-		err = -EBUSY;
-		/* Check if on specified address is a SK_G16 */
-		if (request_region(io, ETHERCARD_TOTAL_SIZE, "sk_g16")) {
-			err = SK_probe(dev, io);
-			if (!err)
-				goto got_it;
-			release_region(io, ETHERCARD_TOTAL_SIZE);
-		}
-	} else if (io > 0) {       /* Don't probe at all */
-		err = -ENXIO;
-	} else {
-		/* Autoprobe base_addr */
-		for (port = &ports[0]; *port; port++) {
-			io = *port;
-
-			/* Check if I/O Port region is used by another board */
-			if (!request_region(io, ETHERCARD_TOTAL_SIZE, "sk_g16"))
-				continue;       /* Try next Port address */
-
-			/* Check if at ioaddr is a SK_G16 */
-			if (SK_probe(dev, io) == 0)
-				goto got_it;
-
-			release_region(io, ETHERCARD_TOTAL_SIZE);
-		}
-	}
-err_out:
-	free_netdev(dev);
-	return ERR_PTR(err);
-
-got_it:
-	err = register_netdev(dev);
-	if (err) {
-		release_region(dev->base_addr, ETHERCARD_TOTAL_SIZE);
-		goto err_out;
-	}
-	return dev;
-
-} /* End of SK_init */
-
-
-MODULE_AUTHOR("Patrick J.D. Weichmann");
-MODULE_DESCRIPTION("Schneider & Koch G16 Ethernet Device Driver");
-MODULE_LICENSE("GPL");
-MODULE_PARM(io, "i");
-MODULE_PARM_DESC(io, "0 to probe common ports (unsafe), or the I/O base of the board");
-
-
-#ifdef MODULE
-
-static struct net_device *SK_dev;
-
-static int __init SK_init_module (void)
-{
- 	SK_dev = SK_init(-1);
- 	return IS_ERR(SK_dev) ? PTR_ERR(SK_dev) : 0;
-}
-
-static void __exit SK_cleanup_module (void)
-{
- 	unregister_netdev(SK_dev);
- 	release_region(SK_dev->base_addr, ETHERCARD_TOTAL_SIZE);
- 	free_netdev(SK_dev);
-}
-
-module_init(SK_init_module);
-module_exit(SK_cleanup_module);
-#endif
-
-
-/*-
- * Function       : SK_probe
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : This function is called by SK_init and 
- *                  does the main part of initialization.
- *                  
- * Parameters     : I : struct net_device *dev - SK_G16 device structure
- *                  I : short ioaddr       - I/O Port address where POS is.
- * Return Value   : 0 = Initialization done             
- * Errors         : ENODEV - No SK_G16 found
- *                  -1     - Configuration problem
- * Globals        : board       - pointer to SK_RAM
- * Update History :
- *     YY/MM/DD  uid  Description
- *     94/06/30  pwe  SK_ADDR now checked and at the correct place
--*/
-
-int __init SK_probe(struct net_device *dev, short ioaddr)
-{
-    int i,j;                /* Counters */
-    int sk_addr_flag = 0;   /* SK ADDR correct? 1 - no, 0 - yes */
-    unsigned int rom_addr;  /* used to store RAM address used for POS_ADDR */
-
-    struct priv *p = netdev_priv(dev);	/* SK_G16 private structure */
-
-    if (inb(SK_POS0) != SK_IDLOW || inb(SK_POS1) != SK_IDHIGH)
-	return -ENODEV;
-    dev->base_addr = ioaddr;
-
-    if (SK_ADDR & 0x3fff || SK_ADDR < 0xa0000)
-    {
-      
-       sk_addr_flag = 1;
-
-       /* 
-        * Now here we could use a routine which searches for a free
-        * place in the ram and set SK_ADDR if found. TODO. 
-        */
-    }
-
-    if (SK_BOOT_ROM)            /* Shall we keep Boot_ROM on ? */
-    {
-        PRINTK(("## %s: SK_BOOT_ROM is set.\n", SK_NAME));
-
-        rom_addr = SK_rom_addr();
-
-	if (rom_addr == 0)      /* No Boot_ROM found */
-	{
-            if (sk_addr_flag)   /* No or Invalid SK_ADDR is defined */ 
-            {
-                printk("%s: SK_ADDR %#08x is not valid. Check configuration.\n",
-                       dev->name, SK_ADDR);
-                return -1;
-            }
-
-	    rom_addr = SK_ADDR; /* assign predefined address */
-
-	    PRINTK(("## %s: NO Bootrom found \n", SK_NAME));
-
-	    outb(SK_ROM_RAM_OFF, SK_POS2); /* Boot_ROM + RAM off */
-	    outb(POS_ADDR, SK_POS3);       /* Set RAM address */
-	    outb(SK_RAM_ON, SK_POS2);      /* enable RAM */
-	}
-	else if (rom_addr == SK_ADDR) 
-	{
-            printk("%s: RAM + ROM are set to the same address %#08x\n"
-                   "   Check configuration. Now switching off Boot_ROM\n",
-                   SK_NAME, rom_addr);
-
-	    outb(SK_ROM_RAM_OFF, SK_POS2); /* Boot_ROM + RAM off*/
-	    outb(POS_ADDR, SK_POS3);       /* Set RAM address */
-	    outb(SK_RAM_ON, SK_POS2);      /* enable RAM */
-	}
-	else
-	{
-            PRINTK(("## %s: Found ROM at %#08x\n", SK_NAME, rom_addr));
-	    PRINTK(("## %s: Keeping Boot_ROM on\n", SK_NAME));
-
-            if (sk_addr_flag)       /* No or Invalid SK_ADDR is defined */ 
-            {
-                printk("%s: SK_ADDR %#08x is not valid. Check configuration.\n",
-                       dev->name, SK_ADDR);
-                return -1;
-            }
-
-	    rom_addr = SK_ADDR;
-
-	    outb(SK_ROM_RAM_OFF, SK_POS2); /* Boot_ROM + RAM off */ 
-	    outb(POS_ADDR, SK_POS3);       /* Set RAM address */
-	    outb(SK_ROM_RAM_ON, SK_POS2);  /* RAM on, BOOT_ROM on */
-	}
-    }
-    else /* Don't keep Boot_ROM */
-    {
-        PRINTK(("## %s: SK_BOOT_ROM is not set.\n", SK_NAME));
-
-        if (sk_addr_flag)           /* No or Invalid SK_ADDR is defined */ 
-        {
-            printk("%s: SK_ADDR %#08x is not valid. Check configuration.\n",
-                   dev->name, SK_ADDR);
-            return -1;
-        }
-
-	rom_addr = SK_rom_addr();          /* Try to find a Boot_ROM */
-
-	/* IF we find a Boot_ROM disable it */
-
-	outb(SK_ROM_RAM_OFF, SK_POS2);     /* Boot_ROM + RAM off */  
-
-        /* We found a Boot_ROM and it's gone. Set RAM address on
-         * Boot_ROM address. 
-         */ 
-
-	if (rom_addr) 
-	{
-            printk("%s: We found Boot_ROM at %#08x. Now setting RAM on"
-                   "that address\n", SK_NAME, rom_addr);
-
-	    outb(POS_ADDR, SK_POS3);       /* Set RAM on Boot_ROM address */
-	}
-	else /* We did not find a Boot_ROM, use predefined SK_ADDR for ram */
-	{
-            if (sk_addr_flag)       /* No or Invalid SK_ADDR is defined */ 
-            {
-                printk("%s: SK_ADDR %#08x is not valid. Check configuration.\n",
-                       dev->name, SK_ADDR);
-                return -1;
-            }
-
-	    rom_addr = SK_ADDR;
-
-	    outb(POS_ADDR, SK_POS3);       /* Set RAM address */ 
-	}
-	outb(SK_RAM_ON, SK_POS2);          /* enable RAM */
-    }
-
-#ifdef SK_DEBUG
-    SK_print_pos(dev, "POS registers after ROM, RAM config");
-#endif
-
-    board = (SK_RAM *) isa_bus_to_virt(rom_addr);
-
-    /* Read in station address */
-    for (i = 0, j = 0; i < ETH_ALEN; i++, j+=2)
-    {
-	dev->dev_addr[i] = readb(board->rom+j);          
-    }
-
-    /* Check for manufacturer code */
-    if (!(dev->dev_addr[0] == SK_MAC0 &&
-	  dev->dev_addr[1] == SK_MAC1 &&
-	  dev->dev_addr[2] == SK_MAC2) )
-    {
-        PRINTK(("## %s: We did not find SK_G16 at RAM location.\n",
-                SK_NAME)); 
-	return -ENODEV;                     /* NO SK_G16 found */
-    }
-
-    printk("%s: %s found at %#3x, HW addr: %#04x:%02x:%02x:%02x:%02x:%02x\n",
-	    dev->name,
-	    "Schneider & Koch Netcard",
-	    (unsigned int) dev->base_addr,
-	    dev->dev_addr[0],
-	    dev->dev_addr[1],
-	    dev->dev_addr[2],
-	    dev->dev_addr[3],
-	    dev->dev_addr[4],
-	    dev->dev_addr[5]);
-
-    memset((char *) dev->priv, 0, sizeof(struct priv)); /* clear memory */
-
-    /* Assign our Device Driver functions */
-
-    dev->open                   = SK_open;
-    dev->stop                   = SK_close;
-    dev->hard_start_xmit        = SK_send_packet;
-    dev->get_stats              = SK_get_stats;
-    dev->set_multicast_list     = set_multicast_list;
-    dev->tx_timeout		= SK_timeout;
-    dev->watchdog_timeo		= HZ/7;
-
-
-    dev->flags &= ~IFF_MULTICAST;
-
-    /* Initialize private structure */
-
-    p->ram = (struct SK_ram *) rom_addr; /* Set dual ported RAM addr */
-    p->tmdhead = &(p->ram)->tmde[0];     /* Set TMD head */
-    p->rmdhead = &(p->ram)->rmde[0];     /* Set RMD head */
-
-    /* Initialize buffer pointers */
-
-    for (i = 0; i < TMDNUM; i++)
-    {
-	p->tmdbufs[i] = &(p->ram)->tmdbuf[i];
-    }
-
-    for (i = 0; i < RMDNUM; i++)
-    {
-	p->rmdbufs[i] = &(p->ram)->rmdbuf[i]; 
-    }
-
-#ifdef SK_DEBUG
-    SK_print_pos(dev, "End of SK_probe");
-    SK_print_ram(dev);
-#endif 
-    return 0;                            /* Initialization done */
-} /* End of SK_probe() */
-
-
-/*- 
- * Function       : SK_open
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : This function is called sometimes after booting 
- *                  when ifconfig program is run.
- *
- *                  This function requests an IRQ, sets the correct
- *                  IRQ in the card. Then calls SK_lance_init() to 
- *                  init and start the LANCE chip. Then if everything is 
- *                  ok returns with 0 (OK), which means SK_G16 is now
- *                  opened and operational.
- *
- *                  (Called by dev_open() /net/inet/dev.c)
- *
- * Parameters     : I : struct net_device *dev - SK_G16 device structure
- * Return Value   : 0 - Device opened
- * Errors         : -EAGAIN - Open failed
- * Side Effects   : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static int SK_open(struct net_device *dev)
-{
-    int i = 0;
-    int irqval = 0;
-    int ioaddr = dev->base_addr;
-
-    int irqtab[] = SK_IRQS; 
-
-    struct priv *p = netdev_priv(dev);
-
-    PRINTK(("## %s: At beginning of SK_open(). CSR0: %#06x\n", 
-           SK_NAME, SK_read_reg(CSR0)));
-
-    if (dev->irq == 0) /* Autoirq */
-    {
-	i = 0;
-
-	/* 
-         * Check if one IRQ out of SK_IRQS is free and install 
-	 * interrupt handler.
-	 * Most done by request_irq(). 
-	 * irqval: 0       - interrupt handler installed for IRQ irqtab[i]
-	 *         -EBUSY  - interrupt busy 
-         *         -EINVAL - irq > 15 or handler = NULL
-	 */
-
-	do
-	{
-	  irqval = request_irq(irqtab[i], &SK_interrupt, 0, "sk_g16", dev);
-	  i++;
-	} while (irqval && irqtab[i]);
-
-	if (irqval) /* We tried every possible IRQ but no success */
-	{
-	    printk("%s: unable to get an IRQ\n", dev->name);
-	    return -EAGAIN;
-	}
-
-	dev->irq = irqtab[--i]; 
-	
-	outb(i<<2, SK_POS4);           /* Set Card on probed IRQ */
-
-    }
-    else if (dev->irq == 2) /* IRQ2 is always IRQ9 */
-    {
-	if (request_irq(9, &SK_interrupt, 0, "sk_g16", dev))
-	{
-	    printk("%s: unable to get IRQ 9\n", dev->name);
-	    return -EAGAIN;
-	} 
-	dev->irq = 9;
-	
-        /* 
-         * Now we set card on IRQ2.
-         * This can be confusing, but remember that IRQ2 on the network
-         * card is in reality IRQ9
-         */
-	outb(0x08, SK_POS4);           /* set card to IRQ2 */
-
-    }
-    else  /* Check IRQ as defined in Space.c */
-    {
-	int i = 0;
-
-	/* check if IRQ free and valid. Then install Interrupt handler */
-
-	if (request_irq(dev->irq, &SK_interrupt, 0, "sk_g16", dev))
-	{
-	    printk("%s: unable to get selected IRQ\n", dev->name);
-	    return -EAGAIN;
-	}
-
-	switch(dev->irq)
-	{
-	    case 3: i = 0;
-		    break;
-	    case 5: i = 1;
-		    break;
-	    case 2: i = 2;
-		    break;
-	    case 11:i = 3;
-		    break;
-	    default: 
-		printk("%s: Preselected IRQ %d is invalid for %s boards",
-		       dev->name,
-		       dev->irq,
-                       SK_NAME);
-		return -EAGAIN;
-	}      
-  
-	outb(i<<2, SK_POS4);           /* Set IRQ on card */
-    }
-
-    printk("%s: Schneider & Koch G16 at %#3x, IRQ %d, shared mem at %#08x\n",
-	    dev->name, (unsigned int)dev->base_addr, 
-	    (int) dev->irq, (unsigned int) p->ram);
-
-    if (!(i = SK_lance_init(dev, 0)))  /* LANCE init OK? */
-    {
-	netif_start_queue(dev);
-
-#ifdef SK_DEBUG
-
-        /* 
-         * This debug block tries to stop LANCE,
-         * reinit LANCE with transmitter and receiver disabled,
-         * then stop again and reinit with NORMAL_MODE
-         */
-
-        printk("## %s: After lance init. CSR0: %#06x\n", 
-               SK_NAME, SK_read_reg(CSR0));
-        SK_write_reg(CSR0, CSR0_STOP);
-        printk("## %s: LANCE stopped. CSR0: %#06x\n", 
-               SK_NAME, SK_read_reg(CSR0));
-        SK_lance_init(dev, MODE_DTX | MODE_DRX);
-        printk("## %s: Reinit with DTX + DRX off. CSR0: %#06x\n", 
-               SK_NAME, SK_read_reg(CSR0));
-        SK_write_reg(CSR0, CSR0_STOP);
-        printk("## %s: LANCE stopped. CSR0: %#06x\n", 
-               SK_NAME, SK_read_reg(CSR0));
-        SK_lance_init(dev, MODE_NORMAL);
-        printk("## %s: LANCE back to normal mode. CSR0: %#06x\n", 
-               SK_NAME, SK_read_reg(CSR0));
-        SK_print_pos(dev, "POS regs before returning OK");
-
-#endif /* SK_DEBUG */
-       
-	return 0;              /* SK_open() is successful */
-    }
-    else /* LANCE init failed */
-    {
-
-	PRINTK(("## %s: LANCE init failed: CSR0: %#06x\n", 
-               SK_NAME, SK_read_reg(CSR0)));
-
-	return -EAGAIN;
-    }
-
-} /* End of SK_open() */
-
-
-/*-
- * Function       : SK_lance_init
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : Reset LANCE chip, fill RMD, TMD structures with
- *                  start values and Start LANCE.
- *
- * Parameters     : I : struct net_device *dev - SK_G16 device structure
- *                  I : int mode - put LANCE into "mode" see data-sheet for
- *                                 more info.
- * Return Value   : 0  - Init done
- * Errors         : -1 - Init failed
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static int SK_lance_init(struct net_device *dev, unsigned short mode)
-{
-    int i;
-    unsigned long flags;
-    struct priv *p = netdev_priv(dev);
-    struct tmd  *tmdp;
-    struct rmd  *rmdp;
-
-    PRINTK(("## %s: At beginning of LANCE init. CSR0: %#06x\n", 
-           SK_NAME, SK_read_reg(CSR0)));
-
-    /* Reset LANCE */
-    SK_reset_board();
-
-    /* Initialize TMD's with start values */
-    p->tmdnum = 0;                   /* First descriptor for transmitting */ 
-    p->tmdlast = 0;                  /* First descriptor for reading stats */
-
-    for (i = 0; i < TMDNUM; i++)     /* Init all TMD's */
-    {
-	tmdp = p->tmdhead + i; 
-   
-	writel((unsigned long) p->tmdbufs[i], tmdp->u.buffer); /* assign buffer */
-	
-	/* Mark TMD as start and end of packet */
-	writeb(TX_STP | TX_ENP, &tmdp->u.s.status);
-    }
-
-
-    /* Initialize RMD's with start values */
-
-    p->rmdnum = 0;                   /* First RMD which will be used */
- 
-    for (i = 0; i < RMDNUM; i++)     /* Init all RMD's */
-    {
-	rmdp = p->rmdhead + i;
-
-	
-	writel((unsigned long) p->rmdbufs[i], rmdp->u.buffer); /* assign buffer */
-	
-	/* 
-         * LANCE must be owner at beginning so that he can fill in 
-	 * receiving packets, set status and release RMD 
-	 */
-
-	writeb(RX_OWN, &rmdp->u.s.status);
-
-	writew(-PKT_BUF_SZ, &rmdp->blen); /* Buffer Size (two's complement) */
-
-	writeb(0, &rmdp->mlen);           /* init message length */       
-	
-    }
-
-    /* Fill LANCE Initialize Block */
-
-    writew(mode, (&((p->ram)->ib.mode))); /* Set operation mode */
-
-    for (i = 0; i < ETH_ALEN; i++)   /* Set physical address */
-    {
-	writeb(dev->dev_addr[i], (&((p->ram)->ib.paddr[i]))); 
-    }
-
-    for (i = 0; i < 8; i++)          /* Set multicast, logical address */
-    {
-	writeb(0, (&((p->ram)->ib.laddr[i]))); /* We do not use logical addressing */
-    } 
-
-    /* Set ring descriptor pointers and set number of descriptors */
-
-    writel((int)p->rmdhead | RMDNUMMASK, (&((p->ram)->ib.rdrp)));
-    writel((int)p->tmdhead | TMDNUMMASK, (&((p->ram)->ib.tdrp)));
-
-    /* Prepare LANCE Control and Status Registers */
-
-    spin_lock_irqsave(&SK_lock, flags);
-
-    SK_write_reg(CSR3, CSR3_ACON);   /* Ale Control !!!THIS MUST BE SET!!!! */
- 
-    /* 
-     * LANCE addresses the RAM from 0x0000 to 0x3fbf and has no access to
-     * PC Memory locations.
-     *
-     * In structure SK_ram is defined that the first thing in ram
-     * is the initialization block. So his address is for LANCE always
-     * 0x0000
-     *
-     * CSR1 contains low order bits 15:0 of initialization block address
-     * CSR2 is built of: 
-     *    7:0  High order bits 23:16 of initialization block address
-     *   15:8  reserved, must be 0
-     */
-    
-    /* Set initialization block address (must be on word boundary) */
-    SK_write_reg(CSR1, 0);          /* Set low order bits 15:0 */
-    SK_write_reg(CSR2, 0);          /* Set high order bits 23:16 */ 
-    
-
-    PRINTK(("## %s: After setting CSR1-3. CSR0: %#06x\n", 
-           SK_NAME, SK_read_reg(CSR0)));
-
-    /* Initialize LANCE */
-
-    /* 
-     * INIT = Initialize, when set, causes the LANCE to begin the
-     * initialization procedure and access the Init Block.
-     */
-
-    SK_write_reg(CSR0, CSR0_INIT); 
-
-    spin_unlock_irqrestore(&SK_lock, flags);
-
-    /* Wait until LANCE finished initialization */
-    
-    SK_set_RAP(CSR0);              /* Register Address Pointer to CSR0 */
-
-    for (i = 0; (i < 100) && !(SK_rread_reg() & CSR0_IDON); i++) 
-	; /* Wait until init done or go ahead if problems (i>=100) */
-
-    if (i >= 100) /* Something is wrong ! */
-    {
-	printk("%s: can't init am7990, status: %04x "
-	       "init_block: %#08x\n", 
-		dev->name, (int) SK_read_reg(CSR0), 
-		(unsigned int) &(p->ram)->ib);
-
-#ifdef SK_DEBUG
-	SK_print_pos(dev, "LANCE INIT failed");
-	SK_print_dev(dev,"Device Structure:");
-#endif
-
-	return -1;                 /* LANCE init failed */
-    }
-
-    PRINTK(("## %s: init done after %d ticks\n", SK_NAME, i));
-
-    /* Clear Initialize done, enable Interrupts, start LANCE */
-
-    SK_write_reg(CSR0, CSR0_IDON | CSR0_INEA | CSR0_STRT);
-
-    PRINTK(("## %s: LANCE started. CSR0: %#06x\n", SK_NAME, 
-            SK_read_reg(CSR0)));
-
-    return 0;                      /* LANCE is up and running */
-
-} /* End of SK_lance_init() */
-
-
-
-/*-
- * Function       : SK_send_packet
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/27
- *
- * Description    : Writes an socket buffer into a transmit descriptor
- *                  and starts transmission.
- *
- * Parameters     : I : struct sk_buff *skb - packet to transfer
- *                  I : struct net_device *dev  - SK_G16 device structure
- * Return Value   : 0 - OK
- *                  1 - Could not transmit (dev_queue_xmit will queue it)
- *                      and try to sent it later
- * Globals        : None
- * Side Effects   : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static void SK_timeout(struct net_device *dev)
-{
-	printk(KERN_WARNING "%s: xmitter timed out, try to restart!\n", dev->name);
-	SK_lance_init(dev, MODE_NORMAL); /* Reinit LANCE */
-	netif_wake_queue(dev);		 /* Clear Transmitter flag */
-	dev->trans_start = jiffies;      /* Mark Start of transmission */
-}
-
-static int SK_send_packet(struct sk_buff *skb, struct net_device *dev)
-{
-    struct priv *p = netdev_priv(dev);
-    struct tmd *tmdp;
-    static char pad[64];
-
-    PRINTK2(("## %s: SK_send_packet() called, CSR0 %#04x.\n", 
-	    SK_NAME, SK_read_reg(CSR0)));
-
-
-    /* 
-     * Block a timer-based transmit from overlapping. 
-     * This means check if we are already in. 
-     */
-
-    netif_stop_queue (dev);
-
-    {
-
-	/* Evaluate Packet length */
-	short len = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN; 
-       
-	tmdp = p->tmdhead + p->tmdnum; /* Which descriptor for transmitting */
-
-	/* Fill in Transmit Message Descriptor */
-
-	/* Copy data into dual ported ram */
-
-	memcpy_toio((tmdp->u.buffer & 0x00ffffff), skb->data, skb->len);
-	if (len != skb->len)
-		memcpy_toio((tmdp->u.buffer & 0x00ffffff) + skb->len, pad, len-skb->len);
-
-	writew(-len, &tmdp->blen);            /* set length to transmit */
-
-	/* 
-	 * Packet start and end is always set because we use the maximum
-	 * packet length as buffer length.
-	 * Relinquish ownership to LANCE
-	 */
-
-	writeb(TX_OWN | TX_STP | TX_ENP, &tmdp->u.s.status);
-	
-	/* Start Demand Transmission */
-	SK_write_reg(CSR0, CSR0_TDMD | CSR0_INEA);
-
-	dev->trans_start = jiffies;   /* Mark start of transmission */
-
-	/* Set pointer to next transmit buffer */
-	p->tmdnum++; 
-	p->tmdnum &= TMDNUM-1; 
-
-	/* Do we own the next transmit buffer ? */
-	if (! (readb(&((p->tmdhead + p->tmdnum)->u.s.status)) & TX_OWN) )
-	{
-	   /* 
-	    * We own next buffer and are ready to transmit, so
-	    * clear busy flag
-	    */
-	   netif_start_queue(dev);
-	}
-
-	p->stats.tx_bytes += skb->len;
-
-    }
-
-    dev_kfree_skb(skb);
-    return 0;  
-} /* End of SK_send_packet */
-
-
-/*-
- * Function       : SK_interrupt
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/27
- *
- * Description    : SK_G16 interrupt handler which checks for LANCE
- *                  Errors, handles transmit and receive interrupts
- *
- * Parameters     : I : int irq, void *dev_id, struct pt_regs * regs -
- * Return Value   : None
- * Errors         : None
- * Globals        : None
- * Side Effects   : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static irqreturn_t SK_interrupt(int irq, void *dev_id, struct pt_regs * regs)
-{
-    int csr0;
-    struct net_device *dev = dev_id;
-    struct priv *p = netdev_priv(dev);
-
-
-    PRINTK2(("## %s: SK_interrupt(). status: %#06x\n", 
-            SK_NAME, SK_read_reg(CSR0)));
-
-    if (dev == NULL)
-    {
-	printk("SK_interrupt(): IRQ %d for unknown device.\n", irq);
-    }
-    
-    spin_lock (&SK_lock);
-
-    csr0 = SK_read_reg(CSR0);      /* store register for checking */
-
-    /* 
-     * Acknowledge all of the current interrupt sources, disable      
-     * Interrupts (INEA = 0) 
-     */
-
-    SK_write_reg(CSR0, csr0 & CSR0_CLRALL); 
-
-    if (csr0 & CSR0_ERR) /* LANCE Error */
-    {
-	printk("%s: error: %04x\n", dev->name, csr0);
-      
-        if (csr0 & CSR0_MISS)      /* No place to store packet ? */
-        { 
-            p->stats.rx_dropped++;
-        }
-    }
-
-    if (csr0 & CSR0_RINT)          /* Receive Interrupt (packet arrived) */ 
-    {
-	SK_rxintr(dev); 
-    }
-
-    if (csr0 & CSR0_TINT)          /* Transmit interrupt (packet sent) */
-    {
-	SK_txintr(dev);
-    }
-
-    SK_write_reg(CSR0, CSR0_INEA); /* Enable Interrupts */
-
-    spin_unlock (&SK_lock);
-    return IRQ_HANDLED;
-} /* End of SK_interrupt() */ 
-
-
-/*-
- * Function       : SK_txintr
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/27
- *
- * Description    : After sending a packet we check status, update
- *                  statistics and relinquish ownership of transmit 
- *                  descriptor ring.
- *
- * Parameters     : I : struct net_device *dev - SK_G16 device structure
- * Return Value   : None
- * Errors         : None
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static void SK_txintr(struct net_device *dev)
-{
-    int tmdstat;
-    struct tmd *tmdp;
-    struct priv *p = netdev_priv(dev);
-
-
-    PRINTK2(("## %s: SK_txintr() status: %#06x\n", 
-            SK_NAME, SK_read_reg(CSR0)));
-
-    tmdp = p->tmdhead + p->tmdlast;     /* Which buffer we sent at last ? */
-
-    /* Set next buffer */
-    p->tmdlast++;
-    p->tmdlast &= TMDNUM-1;
-
-    tmdstat = readb(&tmdp->u.s.status);
-
-    /* 
-     * We check status of transmitted packet.
-     * see LANCE data-sheet for error explanation
-     */
-    if (tmdstat & TX_ERR) /* Error occurred */
-    {
-	int stat2 = readw(&tmdp->status2);
-
-	printk("%s: TX error: %04x %04x\n", dev->name, tmdstat, stat2);
-
-	if (stat2 & TX_TDR)    /* TDR problems? */
-	{
-	    printk("%s: tdr-problems \n", dev->name);
-	}
-
-	if (stat2 & TX_RTRY)   /* Failed in 16 attempts to transmit ? */
-            p->stats.tx_aborted_errors++;   
-        if (stat2 & TX_LCOL)   /* Late collision ? */
-            p->stats.tx_window_errors++; 
-	if (stat2 & TX_LCAR)   /* Loss of Carrier ? */  
-            p->stats.tx_carrier_errors++;
-        if (stat2 & TX_UFLO)   /* Underflow error ? */
-        {
-            p->stats.tx_fifo_errors++;
-
-            /* 
-             * If UFLO error occurs it will turn transmitter of.
-             * So we must reinit LANCE
-             */
-
-            SK_lance_init(dev, MODE_NORMAL);
-        }
-	
-	p->stats.tx_errors++;
-
-	writew(0, &tmdp->status2);             /* Clear error flags */
-    }
-    else if (tmdstat & TX_MORE)        /* Collisions occurred ? */
-    {
-        /* 
-         * Here I have a problem.
-         * I only know that there must be one or up to 15 collisions.
-         * That's why TX_MORE is set, because after 16 attempts TX_RTRY
-         * will be set which means couldn't send packet aborted transfer.
-         *
-         * First I did not have this in but then I thought at minimum
-         * we see that something was not ok.
-         * If anyone knows something better than this to handle this
-         * please report it.
-         */ 
-
-        p->stats.collisions++; 
-    }
-    else   /* Packet sent without any problems */
-    {
-        p->stats.tx_packets++; 
-    }
-
-    /* 
-     * We mark transmitter not busy anymore, because now we have a free
-     * transmit descriptor which can be filled by SK_send_packet and
-     * afterwards sent by the LANCE
-     * 
-     * The function which do handle slow IRQ parts is do_bottom_half()
-     * which runs at normal kernel priority, that means all interrupt are
-     * enabled. (see kernel/irq.c)
-     *  
-     * net_bh does something like this:
-     *  - check if already in net_bh
-     *  - try to transmit something from the send queue
-     *  - if something is in the receive queue send it up to higher 
-     *    levels if it is a known protocol
-     *  - try to transmit something from the send queue
-     */
-
-    netif_wake_queue(dev);
-
-} /* End of SK_txintr() */
-
-
-/*-
- * Function       : SK_rxintr
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/27
- *
- * Description    : Buffer sent, check for errors, relinquish ownership
- *                  of the receive message descriptor. 
- *
- * Parameters     : I : SK_G16 device structure
- * Return Value   : None
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static void SK_rxintr(struct net_device *dev)
-{
-
-    struct rmd *rmdp;
-    int rmdstat;
-    struct priv *p = netdev_priv(dev);
-
-    PRINTK2(("## %s: SK_rxintr(). CSR0: %#06x\n", 
-            SK_NAME, SK_read_reg(CSR0)));
-
-    rmdp = p->rmdhead + p->rmdnum;
-
-    /* As long as we own the next entry, check status and send
-     * it up to higher layer 
-     */
-
-    while (!( (rmdstat = readb(&rmdp->u.s.status)) & RX_OWN))
-    {
-	/* 
-         * Start and end of packet must be set, because we use 
-	 * the ethernet maximum packet length (1518) as buffer size.
-	 * 
-	 * Because our buffers are at maximum OFLO and BUFF errors are
-	 * not to be concerned (see Data sheet)
-	 */
-
-	if ((rmdstat & (RX_STP | RX_ENP)) != (RX_STP | RX_ENP))
-	{
-	    /* Start of a frame > 1518 Bytes ? */
-
-	    if (rmdstat & RX_STP) 
-	    {
-		p->stats.rx_errors++;        /* bad packet received */
-		p->stats.rx_length_errors++; /* packet too long */
-
-		printk("%s: packet too long\n", dev->name);
-	    }
-	    
-	    /* 
-             * All other packets will be ignored until a new frame with
-	     * start (RX_STP) set follows.
-	     * 
-	     * What we do is just give descriptor free for new incoming
-	     * packets. 
-	     */
-
-	    writeb(RX_OWN, &rmdp->u.s.status); /* Relinquish ownership to LANCE */ 
-
-	}
-	else if (rmdstat & RX_ERR)          /* Receive Error ? */
-	{
-	    printk("%s: RX error: %04x\n", dev->name, (int) rmdstat);
-	    
-	    p->stats.rx_errors++;
-
-	    if (rmdstat & RX_FRAM) p->stats.rx_frame_errors++;
-	    if (rmdstat & RX_CRC)  p->stats.rx_crc_errors++;
-
-	    writeb(RX_OWN, &rmdp->u.s.status); /* Relinquish ownership to LANCE */
-
-	}
-	else /* We have a packet which can be queued for the upper layers */
-	{
-
-	    int len = readw(&rmdp->mlen) & 0x0fff;  /* extract message length from receive buffer */
-	    struct sk_buff *skb;
-
-	    skb = dev_alloc_skb(len+2); /* allocate socket buffer */ 
-
-	    if (skb == NULL)                /* Could not get mem ? */
-	    {
-    
-		/* 
-                 * Couldn't allocate sk_buffer so we give descriptor back
-		 * to Lance, update statistics and go ahead.
-		 */
-
-		writeb(RX_OWN, &rmdp->u.s.status); /* Relinquish ownership to LANCE */
-		printk("%s: Couldn't allocate sk_buff, deferring packet.\n",
-		       dev->name);
-		p->stats.rx_dropped++;
-
-		break;                      /* Jump out */
-	    }
-	    
-	    /* Prepare sk_buff to queue for upper layers */
-
-	    skb->dev = dev;
-	    skb_reserve(skb,2);		/* Align IP header on 16 byte boundary */
-	    
-	    /* 
-             * Copy data out of our receive descriptor into sk_buff.
-	     *
-	     * (rmdp->u.buffer & 0x00ffffff) -> get address of buffer and 
-	     * ignore status fields) 
-	     */
-
-	    memcpy_fromio(skb_put(skb,len), (rmdp->u.buffer & 0x00ffffff), len);
-
-
-	    /* 
-             * Notify the upper protocol layers that there is another packet
-	     * to handle
-	     *
-	     * netif_rx() always succeeds. see /net/inet/dev.c for more.
-	     */
-
-	    skb->protocol=eth_type_trans(skb,dev);
-	    netif_rx(skb);                 /* queue packet and mark it for processing */
-	   
-	    /* 
-             * Packet is queued and marked for processing so we
-	     * free our descriptor and update statistics 
-	     */
-
-	    writeb(RX_OWN, &rmdp->u.s.status);
-	    dev->last_rx = jiffies;
-	    p->stats.rx_packets++;
-	    p->stats.rx_bytes += len;
-
-
-	    p->rmdnum++;
-	    p->rmdnum %= RMDNUM;
-
-	    rmdp = p->rmdhead + p->rmdnum;
-	}
-    }
-} /* End of SK_rxintr() */
-
-
-/*-
- * Function       : SK_close
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : close gets called from dev_close() and should
- *                  deinstall the card (free_irq, mem etc).
- *
- * Parameters     : I : struct net_device *dev - our device structure
- * Return Value   : 0 - closed device driver
- * Errors         : None
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-/* I have tried to set BOOT_ROM on and RAM off but then, after a 'ifconfig
- * down' the system stops. So I don't shut set card to init state.
- */
-
-static int SK_close(struct net_device *dev)
-{
-
-    PRINTK(("## %s: SK_close(). CSR0: %#06x\n", 
-           SK_NAME, SK_read_reg(CSR0)));
-
-    netif_stop_queue(dev);	   /* Transmitter busy */
-
-    printk("%s: Shutting %s down CSR0 %#06x\n", dev->name, SK_NAME, 
-           (int) SK_read_reg(CSR0));
-
-    SK_write_reg(CSR0, CSR0_STOP); /* STOP the LANCE */
-
-    free_irq(dev->irq, dev);      /* Free IRQ */
-
-    return 0; /* always succeed */
-    
-} /* End of SK_close() */
-
-
-/*-
- * Function       : SK_get_stats
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : Return current status structure to upper layers.
- *                  It is called by sprintf_stats (dev.c).
- *
- * Parameters     : I : struct net_device *dev   - our device structure
- * Return Value   : struct net_device_stats * - our current statistics
- * Errors         : None
- * Side Effects   : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-static struct net_device_stats *SK_get_stats(struct net_device *dev)
-{
-
-    struct priv *p = netdev_priv(dev);
-
-    PRINTK(("## %s: SK_get_stats(). CSR0: %#06x\n", 
-           SK_NAME, SK_read_reg(CSR0)));
-
-    return &p->stats;             /* Return Device status */
-
-} /* End of SK_get_stats() */
-
-
-/*-
- * Function       : set_multicast_list
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/26
- *
- * Description    : This function gets called when a program performs
- *                  a SIOCSIFFLAGS call. Ifconfig does this if you call
- *                  'ifconfig [-]allmulti' which enables or disables the
- *                  Promiscuous mode.
- *                  Promiscuous mode is when the Network card accepts all
- *                  packets, not only the packets which match our MAC 
- *                  Address. It is useful for writing a network monitor,
- *                  but it is also a security problem. You have to remember
- *                  that all information on the net is not encrypted.
- *
- * Parameters     : I : struct net_device *dev - SK_G16 device Structure
- * Return Value   : None
- * Errors         : None
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
- *     95/10/18  ACox  New multicast calling scheme
--*/
-
-
-/* Set or clear the multicast filter for SK_G16.
- */
-
-static void set_multicast_list(struct net_device *dev)
-{
-
-    if (dev->flags&IFF_PROMISC)
-    {
-	/* Reinitialize LANCE with MODE_PROM set */
-	SK_lance_init(dev, MODE_PROM);
-    }
-    else if (dev->mc_count==0 && !(dev->flags&IFF_ALLMULTI))
-    {
-	/* Reinitialize LANCE without MODE_PROM */
-	SK_lance_init(dev, MODE_NORMAL);
-    }
-    else
-    {
-	/* Multicast with logical address filter on */
-	/* Reinitialize LANCE without MODE_PROM */
-	SK_lance_init(dev, MODE_NORMAL);
-	
-	/* Not implemented yet. */
-    }
-} /* End of set_multicast_list() */
-
-
-
-/*-
- * Function       : SK_rom_addr
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/06/01
- *
- * Description    : Try to find a Boot_ROM at all possible locations
- *
- * Parameters     : None
- * Return Value   : Address where Boot_ROM is
- * Errors         : 0 - Did not find Boot_ROM
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-unsigned int __init SK_rom_addr(void)
-{
-    int i,j;
-    int rom_found = 0;
-    unsigned int rom_location[] = SK_BOOT_ROM_LOCATIONS;
-    unsigned char rom_id[] = SK_BOOT_ROM_ID;
-    unsigned char test_byte;
-
-    /* Autodetect Boot_ROM */
-    PRINTK(("## %s: Autodetection of Boot_ROM\n", SK_NAME));
-
-    for (i = 0; (rom_location[i] != 0) && (rom_found == 0); i++)
-    {
-	
-	PRINTK(("##   Trying ROM location %#08x", rom_location[i]));
-	
-	rom_found = 1; 
-	for (j = 0; j < 6; j++)
-	{
-	    test_byte = readb(rom_location[i]+j);
-	    PRINTK((" %02x ", *test_byte));
-
-	    if(test_byte != rom_id[j])
-	    {
-		rom_found = 0;
-	    } 
-	}
-	PRINTK(("\n"));
-    }
-
-    if (rom_found == 1)
-    {
-	PRINTK(("## %s: Boot_ROM found at %#08x\n", 
-               SK_NAME, rom_location[(i-1)]));
-
-	return (rom_location[--i]);
-    }
-    else
-    {
-	PRINTK(("%s: No Boot_ROM found\n", SK_NAME));
-	return 0;
-    }
-} /* End of SK_rom_addr() */
-
-
-
-/* LANCE access functions 
- *
- * ! CSR1-3 can only be accessed when in CSR0 the STOP bit is set !
- */
-
-
-/*-
- * Function       : SK_reset_board
- *
- * Author         : Patrick J.D. Weichmann
- *
- * Date Created   : 94/05/25
- *
- * Description    : This function resets SK_G16 and all components, but
- *                  POS registers are not changed
- *
- * Parameters     : None
- * Return Value   : None
- * Errors         : None
- * Globals        : SK_RAM *board - SK_RAM structure pointer
- *
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-void SK_reset_board(void)
-{
-    writeb(0x00, SK_PORT);       /* Reset active */
-    mdelay(5);                /* Delay min 5ms */
-    writeb(SK_RESET, SK_PORT);   /* Set back to normal operation */
-
-} /* End of SK_reset_board() */
-
-
-/*-
- * Function       : SK_set_RAP
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/25
- *
- * Description    : Set LANCE Register Address Port to register
- *                  for later data transfer.
- *
- * Parameters     : I : reg_number - which CSR to read/write from/to
- * Return Value   : None
- * Errors         : None
- * Globals        : SK_RAM *board - SK_RAM structure pointer
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-void SK_set_RAP(int reg_number)
-{
-    writew(reg_number, SK_IOREG);
-    writeb(SK_RESET | SK_RAP | SK_WREG, SK_PORT);
-    writeb(SK_DOIO, SK_IOCOM);
-
-    while (readb(SK_PORT) & SK_IORUN) 
-	barrier();
-} /* End of SK_set_RAP() */
-
-
-/*-
- * Function       : SK_read_reg
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/25
- *
- * Description    : Set RAP and read data from a LANCE CSR register
- *
- * Parameters     : I : reg_number - which CSR to read from
- * Return Value   : Register contents
- * Errors         : None
- * Globals        : SK_RAM *board - SK_RAM structure pointer
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-int SK_read_reg(int reg_number)
-{
-    SK_set_RAP(reg_number);
-
-    writeb(SK_RESET | SK_RDATA | SK_RREG, SK_PORT);
-    writeb(SK_DOIO, SK_IOCOM);
-
-    while (readb(SK_PORT) & SK_IORUN)
-	barrier();
-    return (readw(SK_IOREG));
-
-} /* End of SK_read_reg() */
-
-
-/*-
- * Function       : SK_rread_reg
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/28
- *
- * Description    : Read data from preseted register.
- *                  This function requires that you know which
- *                  Register is actually set. Be aware that CSR1-3
- *                  can only be accessed when in CSR0 STOP is set.
- *
- * Return Value   : Register contents
- * Errors         : None
- * Globals        : SK_RAM *board - SK_RAM structure pointer
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-int SK_rread_reg(void)
-{
-    writeb(SK_RESET | SK_RDATA | SK_RREG, SK_PORT);
-
-    writeb(SK_DOIO, SK_IOCOM);
-
-    while (readb(SK_PORT) & SK_IORUN)
-	barrier();
-    return (readw(SK_IOREG));
-
-} /* End of SK_rread_reg() */
-
-
-/*-
- * Function       : SK_write_reg
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/25
- *
- * Description    : This function sets the RAP then fills in the
- *                  LANCE I/O Reg and starts Transfer to LANCE.
- *                  It waits until transfer has ended which is max. 7 ms
- *                  and then it returns.
- *
- * Parameters     : I : reg_number - which CSR to write to
- *                  I : value      - what value to fill into register 
- * Return Value   : None
- * Errors         : None
- * Globals        : SK_RAM *board - SK_RAM structure pointer
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-void SK_write_reg(int reg_number, int value)
-{
-    SK_set_RAP(reg_number);
-
-    writew(value, SK_IOREG);
-    writeb(SK_RESET | SK_RDATA | SK_WREG, SK_PORT);
-    writeb(SK_DOIO, SK_IOCOM);
-
-    while (readb(SK_PORT) & SK_IORUN)
-	barrier();
-} /* End of SK_write_reg */
-
-
-
-/* 
- * Debugging functions
- * -------------------
- */
-
-/*-
- * Function       : SK_print_pos
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/25
- *
- * Description    : This function prints out the 4 POS (Programmable
- *                  Option Select) Registers. Used mainly to debug operation.
- *
- * Parameters     : I : struct net_device *dev - SK_G16 device structure
- *                  I : char * - Text which will be printed as title
- * Return Value   : None
- * Errors         : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-void SK_print_pos(struct net_device *dev, char *text)
-{
-    int ioaddr = dev->base_addr;
-
-    unsigned char pos0 = inb(SK_POS0),
-		  pos1 = inb(SK_POS1),
-		  pos2 = inb(SK_POS2),
-		  pos3 = inb(SK_POS3),
-		  pos4 = inb(SK_POS4);
-
-
-    printk("## %s: %s.\n"
-           "##   pos0=%#4x pos1=%#4x pos2=%#04x pos3=%#08x pos4=%#04x\n",
-           SK_NAME, text, pos0, pos1, pos2, (pos3<<14), pos4);
-
-} /* End of SK_print_pos() */
-
-
-
-/*-
- * Function       : SK_print_dev
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/05/25
- *
- * Description    : This function simply prints out the important fields
- *                  of the device structure.
- *
- * Parameters     : I : struct net_device *dev  - SK_G16 device structure
- *                  I : char *text - Title for printing
- * Return Value   : None
- * Errors         : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-void SK_print_dev(struct net_device *dev, char *text)
-{
-    if (dev == NULL)
-    {
-	printk("## %s: Device Structure. %s\n", SK_NAME, text);
-	printk("## DEVICE == NULL\n");
-    }
-    else
-    {
-	printk("## %s: Device Structure. %s\n", SK_NAME, text);
-	printk("## Device Name: %s Base Address: %#06lx IRQ: %d\n", 
-               dev->name, dev->base_addr, dev->irq);
-	       
-	printk("## next device: %#08x init function: %#08x\n", 
-              (int) dev->next, (int) dev->init);
-    }
-
-} /* End of SK_print_dev() */
-
-
-
-/*-
- * Function       : SK_print_ram
- * Author         : Patrick J.D. Weichmann
- * Date Created   : 94/06/02
- *
- * Description    : This function is used to check how are things set up
- *                  in the 16KB RAM. Also the pointers to the receive and 
- *                  transmit descriptor rings and rx and tx buffers locations.
- *                  It contains a minor bug in printing, but has no effect to the values
- *                  only newlines are not correct.
- *
- * Parameters     : I : struct net_device *dev - SK_G16 device structure
- * Return Value   : None
- * Errors         : None
- * Globals        : None
- * Update History :
- *     YY/MM/DD  uid  Description
--*/
-
-void __init SK_print_ram(struct net_device *dev)
-{
-
-    int i;    
-    struct priv *p = netdev_priv(dev);
-
-    printk("## %s: RAM Details.\n"
-           "##   RAM at %#08x tmdhead: %#08x rmdhead: %#08x initblock: %#08x\n",
-           SK_NAME, 
-           (unsigned int) p->ram,
-           (unsigned int) p->tmdhead, 
-           (unsigned int) p->rmdhead, 
-           (unsigned int) &(p->ram)->ib);
-           
-    printk("##   ");
-
-    for(i = 0; i < TMDNUM; i++)
-    {
-           if (!(i % 3)) /* Every third line do a newline */
-           {
-               printk("\n##   ");
-           }
-        printk("tmdbufs%d: %#08x ", (i+1), (int) p->tmdbufs[i]);
-    }
-    printk("##   ");
-
-    for(i = 0; i < RMDNUM; i++)
-    {
-         if (!(i % 3)) /* Every third line do a newline */
-           {
-               printk("\n##   ");
-           }
-        printk("rmdbufs%d: %#08x ", (i+1), (int) p->rmdbufs[i]);
-    } 
-    printk("\n");
-
-} /* End of SK_print_ram() */
-
diff --git a/drivers/net/sk_g16.h b/drivers/net/sk_g16.h
deleted file mode 100644
index 0a5dc0908a04..000000000000
--- a/drivers/net/sk_g16.h
+++ /dev/null
@@ -1,165 +0,0 @@
-/*-
- *
- * This software may be used and distributed according to the terms
- * of the GNU General Public License, incorporated herein by reference.
- *
- * Module         : sk_g16.h
- * Version        : $Revision$  
- *
- * Author         : M.Hipp (mhipp@student.uni-tuebingen.de)
- * changes by     : Patrick J.D. Weichmann
- *
- * Date Created   : 94/05/25
- *
- * Description    : In here are all necessary definitions of  
- *                  the am7990 (LANCE) chip used for writing a
- *                  network device driver which uses this chip 
- *
- * $Log$
--*/
-
-#ifndef SK_G16_H
-
-#define SK_G16_H
-
-
-/*
- * 	Control and Status Register 0 (CSR0) bit definitions
- *
- * (R=Readable) (W=Writeable) (S=Set on write) (C-Clear on write)
- *
- */
-
-#define CSR0_ERR	0x8000	/* Error summary (R) */
-#define CSR0_BABL	0x4000	/* Babble transmitter timeout error (RC) */
-#define CSR0_CERR	0x2000	/* Collision Error (RC) */
-#define CSR0_MISS	0x1000	/* Missed packet (RC) */
-#define CSR0_MERR	0x0800	/* Memory Error  (RC) */ 
-#define CSR0_RINT	0x0400	/* Receiver Interrupt (RC) */
-#define CSR0_TINT       0x0200	/* Transmit Interrupt (RC) */ 
-#define CSR0_IDON	0x0100	/* Initialization Done (RC) */
-#define CSR0_INTR	0x0080	/* Interrupt Flag (R) */
-#define CSR0_INEA	0x0040	/* Interrupt Enable (RW) */
-#define CSR0_RXON	0x0020	/* Receiver on (R) */
-#define CSR0_TXON	0x0010  /* Transmitter on (R) */
-#define CSR0_TDMD	0x0008	/* Transmit Demand (RS) */
-#define CSR0_STOP	0x0004 	/* Stop (RS) */
-#define CSR0_STRT	0x0002	/* Start (RS) */
-#define CSR0_INIT	0x0001	/* Initialize (RS) */
-
-#define CSR0_CLRALL     0x7f00  /* mask for all clearable bits */
-
-/*
- *    Control and Status Register 3 (CSR3) bit definitions
- *
- */
-
-#define CSR3_BSWAP	0x0004	/* Byte Swap (RW) */
-#define CSR3_ACON	0x0002  /* ALE Control (RW) */
-#define CSR3_BCON	0x0001	/* Byte Control (RW) */
-
-/*
- *	Initialization Block Mode operation Bit Definitions.
- */
-
-#define MODE_PROM	0x8000	/* Promiscuous Mode */
-#define MODE_INTL	0x0040  /* Internal Loopback */
-#define MODE_DRTY	0x0020  /* Disable Retry */ 
-#define MODE_COLL	0x0010	/* Force Collision */
-#define MODE_DTCR	0x0008	/* Disable Transmit CRC) */
-#define MODE_LOOP	0x0004	/* Loopback */
-#define MODE_DTX	0x0002	/* Disable the Transmitter */ 
-#define MODE_DRX	0x0001  /* Disable the Receiver */
-
-#define MODE_NORMAL 	0x0000  /* Normal operation mode */
-
-/*
- * 	Receive message descriptor status bit definitions.
- */
-
-#define RX_OWN		0x80	/* Owner bit 0 = host, 1 = lance */
-#define RX_ERR		0x40	/* Error Summary */
-#define RX_FRAM		0x20	/* Framing Error */
-#define RX_OFLO		0x10	/* Overflow Error */
-#define RX_CRC		0x08	/* CRC Error */ 
-#define RX_BUFF		0x04	/* Buffer Error */
-#define RX_STP		0x02	/* Start of Packet */
-#define RX_ENP		0x01	/* End of Packet */
-
-
-/*
- *	Transmit message descriptor status bit definitions.
- */
-
-#define TX_OWN		0x80	/* Owner bit 0 = host, 1 = lance */
-#define TX_ERR		0x40    /* Error Summary */
-#define TX_MORE		0x10	/* More the 1 retry needed to Xmit */
-#define TX_ONE		0x08	/* One retry needed to Xmit */
-#define TX_DEF		0x04	/* Deferred */
-#define TX_STP 		0x02	/* Start of Packet */
-#define TX_ENP		0x01	/* End of Packet */
-
-/*
- *      Transmit status (2) (valid if TX_ERR == 1)
- */
-
-#define TX_BUFF 	0x8000  /* Buffering error (no ENP) */
-#define TX_UFLO 	0x4000  /* Underflow (late memory) */
-#define TX_LCOL 	0x1000  /* Late collision */
-#define TX_LCAR 	0x0400  /* Loss of Carrier */
-#define TX_RTRY 	0x0200  /* Failed after 16 retransmissions  */
-#define TX_TDR          0x003f  /* Time-domain-reflectometer-value */
-
-
-/* 
- * Structures used for Communication with the LANCE 
- */
-
-/* LANCE Initialize Block */
-
-struct init_block 
-{
-  unsigned short mode;     /* Mode Register */
-  unsigned char  paddr[6]; /* Physical Address (MAC) */
-  unsigned char  laddr[8]; /* Logical Filter Address (not used) */
-  unsigned int   rdrp;     /* Receive Descriptor Ring pointer */
-  unsigned int   tdrp;     /* Transmit Descriptor Ring pointer */
-};
-
-
-/* Receive Message Descriptor Entry */
-
-struct rmd 
-{ 
-  union
-  {
-    unsigned long buffer;     /* Address of buffer */
-    struct 
-    {
-      unsigned char unused[3]; 
-      unsigned volatile char status;   /* Status Bits */
-    } s;
-  } u;
-  volatile short blen;        /* Buffer Length (two's complement) */
-  unsigned short mlen;        /* Message Byte Count */
-};
-
-
-/* Transmit Message Descriptor Entry */
-
-struct tmd   
-{
-  union 
-  {
-    unsigned long  buffer;    /* Address of buffer */
-    struct 
-    {
-      unsigned char unused[3];
-      unsigned volatile char status;   /* Status Bits */
-    } s;
-  } u;
-  unsigned short blen;             /* Buffer Length (two's complement) */
-  unsigned volatile short status2; /* Error Status Bits */
-};
-
-#endif /* End of SK_G16_H */