Merge branch 'asoc-5.6' into asoc-next

11 files changed, 346 insertions, 44 deletions

diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt
index 3080979350a0..fa4545ed81ca 100644
--- a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt
+++ b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt
@@ -17,6 +17,9 @@ Required properties:
   * "arb" : memory ARB line (required)
   * "rst" : dedicated device reset line (optional)
 - #sound-dai-cells: must be 0.
+- amlogic,fifo-depth: The size of the controller's fifo in bytes. This
+  		      is useful for determining certain configuration such
+		      as the flush threshold of the fifo
 
 Example of FRDDR A on the A113 SoC:
 
@@ -27,4 +30,5 @@ frddr_a: audio-controller@1c0 {
 	interrupts = <GIC_SPI 88 IRQ_TYPE_EDGE_RISING>;
 	clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
 	resets = <&arb AXG_ARB_FRDDR_A>;
+	fifo-depth = <512>;
 };
diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt
index 1d4d9f938689..cb9a25165503 100644
--- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt
+++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt
@@ -8,7 +8,12 @@ three substreams within totally 10 channels.
 
 Required properties:
 
-  - compatible		: Contains "fsl,imx35-asrc" or "fsl,imx53-asrc".
+  - compatible		: Compatible list, should contain one of the following
+			  compatibles:
+			  "fsl,imx35-asrc",
+			  "fsl,imx53-asrc",
+			  "fsl,imx8qm-asrc",
+			  "fsl,imx8qxp-asrc",
 
   - reg			: Offset and length of the register set for the device.
 
@@ -35,6 +40,11 @@ Required properties:
 
    - fsl,asrc-width	: Defines a mutual sample width used by DPCM Back Ends.
 
+   - fsl,asrc-clk-map   : Defines clock map used in driver. which is required
+			  by imx8qm/imx8qxp platform
+			  <0> - select the map for asrc0 in imx8qm/imx8qxp
+			  <1> - select the map for asrc1 in imx8qm/imx8qxp
+
 Optional properties:
 
    - big-endian		: If this property is absent, the little endian mode
diff --git a/Documentation/devicetree/bindings/sound/gtm601.txt b/Documentation/devicetree/bindings/sound/gtm601.txt
index 5efc8c068de0..efa32a486c4a 100644
--- a/Documentation/devicetree/bindings/sound/gtm601.txt
+++ b/Documentation/devicetree/bindings/sound/gtm601.txt
@@ -1,10 +1,16 @@
 GTM601 UMTS modem audio interface CODEC
 
-This device has no configuration interface. Sample rate is fixed - 8kHz.
+This device has no configuration interface. The sample rate and channels are
+based on the compatible string
+	"option,gtm601" = 8kHz mono
+	"broadmobi,bm818" = 48KHz stereo
 
 Required properties:
 
-  - compatible : "option,gtm601"
+  - compatible : one of
+	"option,gtm601"
+	"broadmobi,bm818"
+
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/sound/ingenic,codec.yaml b/Documentation/devicetree/bindings/sound/ingenic,codec.yaml
new file mode 100644
index 000000000000..eb4be86464bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/ingenic,codec.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/ingenic,codec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic JZ47xx internal codec DT bindings
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+properties:
+  $nodename:
+    pattern: '^audio-codec@.*'
+
+  compatible:
+    oneOf:
+      - const: ingenic,jz4770-codec
+      - const: ingenic,jz4725b-codec
+      - const: ingenic,jz4740-codec
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: aic
+
+  '#sound-dai-cells':
+    const: 0
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#sound-dai-cells'
+
+examples:
+  - |
+    #include <dt-bindings/clock/jz4740-cgu.h>
+    codec: audio-codec@10020080 {
+      compatible = "ingenic,jz4740-codec";
+      reg = <0x10020080 0x8>;
+      #sound-dai-cells = <0>;
+      clocks = <&cgu JZ4740_CLK_AIC>;
+      clock-names = "aic";
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt
deleted file mode 100644
index 05adc0d47b13..000000000000
--- a/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt
+++ /dev/null
@@ -1,20 +0,0 @@
-Ingenic JZ4725B codec controller
-
-Required properties:
-- compatible : "ingenic,jz4725b-codec"
-- reg : codec registers location and length
-- clocks : phandle to the AIC clock.
-- clock-names: must be set to "aic".
-- #sound-dai-cells: Must be set to 0.
-
-Example:
-
-codec: audio-codec@100200a4 {
-	compatible = "ingenic,jz4725b-codec";
-	reg = <0x100200a4 0x8>;
-
-	#sound-dai-cells = <0>;
-
-	clocks = <&cgu JZ4725B_CLK_AIC>;
-	clock-names = "aic";
-};
diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt
deleted file mode 100644
index 1ffcade87e7b..000000000000
--- a/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt
+++ /dev/null
@@ -1,20 +0,0 @@
-Ingenic JZ4740 codec controller
-
-Required properties:
-- compatible : "ingenic,jz4740-codec"
-- reg : codec registers location and length
-- clocks : phandle to the AIC clock.
-- clock-names: must be set to "aic".
-- #sound-dai-cells: Must be set to 0.
-
-Example:
-
-codec: audio-codec@10020080 {
-	compatible = "ingenic,jz4740-codec";
-	reg = <0x10020080 0x8>;
-
-	#sound-dai-cells = <0>;
-
-	clocks = <&cgu JZ4740_CLK_AIC>;
-	clock-names = "aic";
-};
diff --git a/Documentation/devicetree/bindings/sound/qcom,sdm845.txt b/Documentation/devicetree/bindings/sound/qcom,sdm845.txt
index 408c4837e6d5..ca8c89e88bfa 100644
--- a/Documentation/devicetree/bindings/sound/qcom,sdm845.txt
+++ b/Documentation/devicetree/bindings/sound/qcom,sdm845.txt
@@ -5,7 +5,10 @@ This binding describes the SDM845 sound card, which uses qdsp for audio.
 - compatible:
 	Usage: required
 	Value type: <stringlist>
-	Definition: must be "qcom,sdm845-sndcard"
+	Definition: must be one of this
+			"qcom,sdm845-sndcard"
+			"qcom,db845c-sndcard"
+			"lenovo,yoga-c630-sndcard"
 
 - audio-routing:
 	Usage: Optional
diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
new file mode 100644
index 000000000000..38eaf0c028f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/qcom,wcd934x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for Qualcomm WCD9340/WCD9341 Audio Codec
+
+maintainers:
+  - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
+
+description: |
+  Qualcomm WCD9340/WCD9341 Codec is a standalone Hi-Fi audio codec IC.
+  It has in-built Soundwire controller, pin controller, interrupt mux and
+  supports both I2S/I2C and SLIMbus audio interfaces.
+
+properties:
+  compatible:
+    const: slim217,250
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description: GPIO spec for reset line to use
+    maxItems: 1
+
+  slim-ifc-dev: true
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: extclk
+
+  vdd-buck-supply:
+    description: A reference to the 1.8V buck supply
+
+  vdd-buck-sido-supply:
+    description: A reference to the 1.8V SIDO buck supply
+
+  vdd-rx-supply:
+    description: A reference to the 1.8V rx supply
+
+  vdd-tx-supply:
+    description: A reference to the 1.8V tx supply
+
+  vdd-vbat-supply:
+    description: A reference to the vbat supply
+
+  vdd-io-supply:
+    description: A reference to the 1.8V I/O supply
+
+  vdd-micbias-supply:
+    description: A reference to the micbias supply
+
+  qcom,micbias1-microvolt:
+    description: micbias1 voltage
+    minimum: 1800000
+    maximum: 2850000
+
+  qcom,micbias2-microvolt:
+    description: micbias2 voltage
+    minimum: 1800000
+    maximum: 2850000
+
+  qcom,micbias3-microvolt:
+    description: micbias3 voltage
+    minimum: 1800000
+    maximum: 2850000
+
+  qcom,micbias4-microvolt:
+    description: micbias4 voltage
+    minimum: 1800000
+    maximum: 2850000
+
+  clock-output-names:
+    const: mclk
+
+  clock-frequency:
+    description: Clock frequency of output clk in Hz
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 1
+
+  '#clock-cells':
+    const: 0
+
+  '#sound-dai-cells':
+    const: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  gpio@42:
+    type: object
+    allOf:
+      - $ref: ../gpio/qcom,wcd934x-gpio.yaml#
+
+patternProperties:
+  "^.*@[0-9a-f]+$":
+    type: object
+    description: |
+      WCD934x subnode for each slave devices. Bindings of each subnodes
+      depends on the specific driver providing the functionality and
+      documented in their respective bindings.
+
+    properties:
+      reg:
+        maxItems: 1
+
+    required:
+      - reg
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - slim-ifc-dev
+  - interrupts
+  - interrupt-controller
+  - clock-frequency
+  - clock-output-names
+  - qcom,micbias1-microvolt
+  - qcom,micbias2-microvolt
+  - qcom,micbias3-microvolt
+  - qcom,micbias4-microvolt
+  - "#interrupt-cells"
+  - "#clock-cells"
+  - "#sound-dai-cells"
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    codec@1,0{
+        compatible = "slim217,250";
+        reg  = <1 0>;
+        reset-gpios = <&tlmm 64 0>;
+        slim-ifc-dev  = <&wcd9340_ifd>;
+        #sound-dai-cells = <1>;
+        interrupt-parent = <&tlmm>;
+        interrupts = <54 4>;
+        interrupt-controller;
+        #interrupt-cells = <1>;
+        #clock-cells = <0>;
+        clock-frequency = <9600000>;
+        clock-output-names = "mclk";
+        qcom,micbias1-microvolt = <1800000>;
+        qcom,micbias2-microvolt = <1800000>;
+        qcom,micbias3-microvolt = <1800000>;
+        qcom,micbias4-microvolt = <1800000>;
+        clock-names = "extclk";
+        clocks = <&rpmhcc 2>;
+
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        gpio@42 {
+            compatible = "qcom,wcd9340-gpio";
+            reg = <0x42 0x2>;
+            gpio-controller;
+            #gpio-cells = <2>;
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
new file mode 100644
index 000000000000..ea44d03e58ca
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/qcom,wsa881x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for Qualcomm WSA8810/WSA8815 Class-D Smart Speaker Amplifier
+
+maintainers:
+  - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
+
+description: |
+  WSA8810 is a class-D smart speaker amplifier and WSA8815
+  is a high-output power class-D smart speaker amplifier.
+  Their primary operating mode uses a SoundWire digital audio
+  interface. This binding is for SoundWire interface.
+
+properties:
+  compatible:
+    const: sdw10217201000
+
+  reg:
+    maxItems: 1
+
+  powerdown-gpios:
+    description: GPIO spec for Powerdown/Shutdown line to use
+    maxItems: 1
+
+  '#thermal-sensor-cells':
+    const: 0
+
+  '#sound-dai-cells':
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - powerdown-gpios
+  - "#thermal-sensor-cells"
+  - "#sound-dai-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    soundwire@c2d0000 {
+        #address-cells = <2>;
+        #size-cells = <0>;
+        reg = <0x0c2d0000 0x2000>;
+
+        speaker@0,1 {
+            compatible = "sdw10217201000";
+            reg = <0 1>;
+            powerdown-gpios = <&wcdpinctrl 2 0>;
+            #thermal-sensor-cells = <0>;
+            #sound-dai-cells = <0>;
+        };
+
+        speaker@0,2 {
+            compatible = "sdw10217201000";
+            reg = <0 2>;
+            powerdown-gpios = <&wcdpinctrl 2 0>;
+            #thermal-sensor-cells = <0>;
+            #sound-dai-cells = <0>;
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/sound/rt1015.txt b/Documentation/devicetree/bindings/sound/rt1015.txt
new file mode 100644
index 000000000000..fcfd02d8d32f
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/rt1015.txt
@@ -0,0 +1,17 @@
+RT1015 Mono Class D Audio Amplifier
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "realtek,rt1015".
+
+- reg : The I2C address of the device.
+
+
+Example:
+
+rt1015: codec@28 {
+	compatible = "realtek,rt1015";
+	reg = <0x28>;
+};
diff --git a/Documentation/devicetree/bindings/sound/rt5645.txt b/Documentation/devicetree/bindings/sound/rt5645.txt
index a03f9a872a71..41a62fd2ae1f 100644
--- a/Documentation/devicetree/bindings/sound/rt5645.txt
+++ b/Documentation/devicetree/bindings/sound/rt5645.txt
@@ -10,6 +10,10 @@ Required properties:
 
 - interrupts : The CODEC's interrupt output.
 
+- avdd-supply: Power supply for AVDD, providing 1.8V.
+
+- cpvdd-supply: Power supply for CPVDD, providing 3.5V.
+
 Optional properties:
 
 - hp-detect-gpios: