path: root/Documentation
diff options
authorLinus Torvalds <torvalds@linux-foundation.org>2013-02-26 09:31:09 -0800
committerLinus Torvalds <torvalds@linux-foundation.org>2013-02-26 09:31:09 -0800
commited5dc2372dba46e0ecd08791b1a0399d313e5cff (patch)
tree571319985b59a2963fb7580c24ee2aa1696359e2 /Documentation
parentMerge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds (diff)
parentmmc: tegra: assume CONFIG_OF, remove platform data (diff)
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball: "MMC highlights for 3.9: Core: - Support for packed commands in eMMC 4.5. (This requires a host capability to be turned on. It increases write throughput by 20%+, but may also increase average write latency; more testing needed.) - Add DT bindings for capability flags. - Add mmc_of_parse() for shared DT parsing between drivers. Drivers: - android-goldfish: New MMC driver for the Android Goldfish emulator. - mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection. - omap_hsmmc: Fix boot hangs with RPMB partitions. - sdhci-bcm2835: New driver for controller used by Raspberry Pi. - sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio. - sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs. - tmio_mmc: Add DT bindings, support for vccq regulator" * tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits) mmc: tegra: assume CONFIG_OF, remove platform data mmc: add DT bindings for more MMC capability flags mmc: tmio: add support for the VccQ regulator mmc: tmio: remove unused and deprecated symbols mmc: sh_mobile_sdhi: use managed resource allocations mmc: sh_mobile_sdhi: remove unused .pdata field mmc: tmio-mmc: parse device-tree bindings mmc: tmio-mmc: define device-tree bindings mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings mmc: (cosmetic) remove "extern" from function declarations mmc: provide a standard MMC device-tree binding parser centrally mmc: detailed definition of CD and WP MMC line polarities in DT mmc: sdhi, tmio: only check flags in tmio-mmc driver proper mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch() mmc: sdhci: check voltage range only on regulators aware of voltage value mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK mmc: support packed write command for eMMC4.5 devices mmc: add packed command feature of eMMC4.5 mmc: rtsx: remove driving adjustment mmc: use regulator_can_change_voltage() instead of regulator_count_voltages ...
Diffstat (limited to 'Documentation')
5 files changed, 93 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt
new file mode 100644
index 000000000000..59476fbdbfa1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt
@@ -0,0 +1,18 @@
+Broadcom BCM2835 SDHCI controller
+This file documents differences between the core properties described
+by mmc.txt and the properties that represent the BCM2835 controller.
+Required properties:
+- compatible : Should be "brcm,bcm2835-sdhci".
+- clocks : The clock feeding the SDHCI controller.
+sdhci: sdhci {
+ compatible = "brcm,bcm2835-sdhci";
+ reg = <0x7e300000 0x100>;
+ interrupts = <2 30>;
+ clocks = <&clk_mmc>;
+ bus-width = <4>;
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index a591c6741d75..85aada2263d5 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -6,23 +6,45 @@ Interpreted by the OF core:
- reg: Registers location and length.
- interrupts: Interrupts used by the MMC controller.
-Required properties:
-- bus-width: Number of data lines, can be <1>, <4>, or <8>
Card detection:
-If no property below is supplied, standard SDHCI card detect is used.
+If no property below is supplied, host native card detect is used.
Only one of the properties in this section should be supplied:
- broken-cd: There is no card detection available; polling must be used.
- cd-gpios: Specify GPIOs for card detection, see gpio binding
- non-removable: non-removable slot (like eMMC); assume always present.
Optional properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default
+ will be <1> if the property is absent.
- wp-gpios: Specify GPIOs for write protection, see gpio binding
-- cd-inverted: when present, polarity on the cd gpio line is inverted
-- wp-inverted: when present, polarity on the wp gpio line is inverted
+- cd-inverted: when present, polarity on the CD line is inverted. See the note
+ below for the case, when a GPIO is used for the CD line
+- wp-inverted: when present, polarity on the WP line is inverted. See the note
+ below for the case, when a GPIO is used for the WP line
- max-frequency: maximum operating clock frequency
- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
this system, even if the controller claims it is.
+- cap-sd-highspeed: SD high-speed timing is supported
+- cap-mmc-highspeed: MMC high-speed timing is supported
+- cap-power-off-card: powering off the card is safe
+- cap-sdio-irq: enable SDIO IRQ signalling on this interface
+*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
+polarity properties, we have to fix the meaning of the "normal" and "inverted"
+line levels. We choose to follow the SDHCI standard, which specifies both those
+lines as "active low." Therefore, using the "cd-inverted" property means, that
+the CD line is active high, i.e. it is high, when a card is inserted. Similar
+logic applies to the "wp-inverted" property.
+CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
+specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
+dedicated pins can be specified, using *-inverted properties. GPIO polarity can
+also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity
+in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
+This means, the two properties are "superimposed," for example leaving the
+OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted
+property results in a double-inversion and actually means the "normal" line
+polarity is in effect.
Optional SDIO properties:
- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
diff --git a/Documentation/devicetree/bindings/mmc/orion-sdio.txt b/Documentation/devicetree/bindings/mmc/orion-sdio.txt
new file mode 100644
index 000000000000..84f0ebd67a13
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/orion-sdio.txt
@@ -0,0 +1,17 @@
+* Marvell orion-sdio controller
+This file documents differences between the core properties in mmc.txt
+and the properties used by the orion-sdio driver.
+- compatible: Should be "marvell,orion-sdio"
+- clocks: reference to the clock of the SDIO interface
+ mvsdio@d00d4000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0xd00d4000 0x200>;
+ interrupts = <54>;
+ clocks = <&gateclk 17>;
+ status = "disabled";
+ };
diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
index 06cd32d08052..726fd2122a13 100644
--- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
@@ -26,8 +26,16 @@ Required Properties:
* bus-width: as documented in mmc core bindings.
* wp-gpios: specifies the write protect gpio line. The format of the
- gpio specifier depends on the gpio controller. If the write-protect
- line is not available, this property is optional.
+ gpio specifier depends on the gpio controller. If a GPIO is not used
+ for write-protect, this property is optional.
+ * disable-wp: If the wp-gpios property isn't present then (by default)
+ we'd assume that the write protect is hooked up directly to the
+ controller's special purpose write protect line (accessible via
+ the WRTPRT register). However, it's possible that we simply don't
+ want write protect. In that case specify 'disable-wp'.
+ NOTE: This property is not required for slots known to always
+ connect to eMMC or SDIO cards.
Optional properties:
diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
new file mode 100644
index 000000000000..df204e18e030
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
@@ -0,0 +1,20 @@
+* Toshiba Mobile IO SD/MMC controller
+The tmio-mmc driver doesn't probe its devices actively, instead its binding to
+devices is managed by either MFD drivers or by the sh_mobile_sdhi platform
+driver. Those drivers supply the tmio-mmc driver with platform data, that either
+describe hardware capabilities, known to them, or are obtained by them from
+their own platform data or from their DT information. In the latter case all
+compulsory and any optional properties, common to all SD/MMC drivers, as
+described in mmc.txt, can be used. Additionally the following tmio_mmc-specific
+optional bindings can be used.
+Optional properties:
+- toshiba,mmc-wrprotect-disable: write-protect detection is unavailable
+When used with Renesas SDHI hardware, the following compatibility strings
+configure various model-specific properties:
+"renesas,sh7372-sdhi": (default) compatible with SH7372
+"renesas,r8a7740-sdhi": compatible with R8A7740: certain MMC/SD commands have to
+ wait for the interface to become idle.