Merge branch 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Highlights:

   - class based instantiation finally dropped for most embedded drivers
     bringing boot up performance gains
   - removed two drivers (one outdated, one a duplicate)
   - ACPI has now operation region support (thanks to Lan Tianyu)
   - the i2c-stub driver got overhauled and gained new features to
     become more useful when writing i2c client drivers (thanks to
     Guenter Roeck and Jean Delvare)

  The rest is driver bugfixes, added bindings/ids, cleanups..."

* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
  i2c: mpc: delete unneeded test before of_node_put
  i2c: rk3x: fix interrupt handling issue
  i2c: imx: Fix format warning for dev_dbg
  i2c: qup: disable clks and return instead of just returning error
  i2c: exynos5: always enable HSI2C
  i2c: designware: add new bindings
  i2c: gpio: Drop dead code in i2c_gpio_remove
  i2c: pca954x: put the mux to disconnected state after resume
  i2c: st: Update i2c timings
  drivers/i2c/busses: use correct type for dma_map/unmap
  i2c: i2c-st: Use %pa to print 'resource_size_t' type
  i2c: s3c2410: resume the I2C controller earlier
  i2c: stub: Avoid an array overrun on I2C block transfers
  i2c: i801: Add device ID for Intel Wildcat Point PCH
  i2c: i801: Fix the alignment of the device table
  i2c: stub: Add support for banked register ranges
  i2c: stub: Remember the number of emulated chips
  i2c: stub: Add support for SMBus block commands
  i2c: efm32: correct namespacing of location property
  i2c: exynos5: remove extra line and fix an assignment
  ...

3 files changed, 20 insertions, 8 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
index fc15ac519437..50b25c3da186 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
@@ -10,7 +10,7 @@ Required properties :
 Recommended properties :
 
  - clock-frequency : maximal I2C bus clock frequency in Hz.
- - efm32,location : Decides the location of the USART I/O pins.
+ - energymicro,location : Decides the location of the USART I/O pins.
    Allowed range : [0 .. 6]
 
 Example:
@@ -23,7 +23,7 @@ Example:
 		clocks = <&cmu clk_HFPERCLKI2C0>;
 		clock-frequency = <100000>;
 		status = "ok";
-		efm32,location = <3>;
+		energymicro,location = <3>;
 
 		eeprom@50 {
 			compatible = "microchip,24c02";
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index adf5e33e8312..e9c803ea306d 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -25,6 +25,7 @@ Supported adapters:
   * Intel Avoton (SOC)
   * Intel Wellsburg (PCH)
   * Intel Coleto Creek (PCH)
+  * Intel Wildcat Point (PCH)
   * Intel Wildcat Point-LP (PCH)
   * Intel BayTrail (SOC)
    Datasheets: Publicly available at the Intel website
diff --git a/Documentation/i2c/i2c-stub b/Documentation/i2c/i2c-stub
index fa4b669c166b..a16924fbd289 100644
--- a/Documentation/i2c/i2c-stub
+++ b/Documentation/i2c/i2c-stub
@@ -2,9 +2,9 @@ MODULE: i2c-stub
 
 DESCRIPTION:
 
-This module is a very simple fake I2C/SMBus driver.  It implements five
+This module is a very simple fake I2C/SMBus driver.  It implements six
 types of SMBus commands: write quick, (r/w) byte, (r/w) byte data, (r/w)
-word data, and (r/w) I2C block data.
+word data, (r/w) I2C block data, and (r/w) SMBus block data.
 
 You need to provide chip addresses as a module parameter when loading this
 driver, which will then only react to SMBus commands to these addresses.
@@ -19,6 +19,14 @@ A pointer register with auto-increment is implemented for all byte
 operations.  This allows for continuous byte reads like those supported by
 EEPROMs, among others.
 
+SMBus block command support is disabled by default, and must be enabled
+explicitly by setting the respective bits (0x03000000) in the functionality
+module parameter.
+
+SMBus block commands must be written to configure an SMBus command for
+SMBus block operations. Writes can be partial. Block read commands always
+return the number of bytes selected with the largest write so far.
+
 The typical use-case is like this:
 	1. load this module
 	2. use i2cset (from the i2c-tools project) to pre-load some data
@@ -39,15 +47,18 @@ unsigned long functionality:
 	value 0x1f0000 would only enable the quick, byte and byte data
 	commands.
 
+u8 bank_reg[10]
+u8 bank_mask[10]
+u8 bank_start[10]
+u8 bank_end[10]:
+	Optional bank settings. They tell which bits in which register
+	select the active bank, as well as the range of banked registers.
+
 CAVEATS:
 
 If your target driver polls some byte or word waiting for it to change, the
 stub could lock it up.  Use i2cset to unlock it.
 
-If the hardware for your driver has banked registers (e.g. Winbond sensors
-chips) this module will not work well - although it could be extended to
-support that pretty easily.
-
 If you spam it hard enough, printk can be lossy.  This module really wants
 something like relayfs.