signal/mips: Use force_sig_fault where appropriate

Filling in struct siginfo before calling force_sig_info a tedious and
error prone process, where once in a great while the wrong fields
are filled out, and siginfo has been inconsistently cleared.

Simplify this process by using the helper force_sig_fault.  Which
takes as a parameters all of the information it needs, ensures
all of the fiddly bits of filling in struct siginfo are done properly
and then calls force_sig_info.

In short about a 5 line reduction in code for every time force_sig_info
is called, which makes the calling function clearer.

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

1 files changed, 5 insertions, 14 deletions

diff --git a/arch/mips/mm/fault.c b/arch/mips/mm/fault.c
index 75392becd933..5f71f2b903b7 100644
--- a/arch/mips/mm/fault.c
+++ b/arch/mips/mm/fault.c
@@ -42,7 +42,7 @@ static void __kprobes __do_page_fault(struct pt_regs *regs, unsigned long write,
 	struct task_struct *tsk = current;
 	struct mm_struct *mm = tsk->mm;
 	const int field = sizeof(unsigned long) * 2;
-	siginfo_t info;
+	int si_code;
 	int fault;
 	unsigned int flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE;
 
@@ -63,8 +63,7 @@ static void __kprobes __do_page_fault(struct pt_regs *regs, unsigned long write,
 		return;
 #endif
 
-	clear_siginfo(&info);
-	info.si_code = SEGV_MAPERR;
+	si_code = SEGV_MAPERR;
 
 	/*
 	 * We fault-in kernel-space virtual memory on-demand. The
@@ -113,7 +112,7 @@ retry:
  * we can handle it..
  */
 good_area:
-	info.si_code = SEGV_ACCERR;
+	si_code = SEGV_ACCERR;
 
 	if (write) {
 		if (!(vma->vm_flags & VM_WRITE))
@@ -224,11 +223,7 @@ bad_area_nosemaphore:
 			pr_cont("\n");
 		}
 		current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
-		info.si_signo = SIGSEGV;
-		info.si_errno = 0;
-		/* info.si_code has been set above */
-		info.si_addr = (void __user *) address;
-		force_sig_info(SIGSEGV, &info, tsk);
+		force_sig_fault(SIGSEGV, si_code, (void __user *)address, tsk);
 		return;
 	}
 
@@ -284,11 +279,7 @@ do_sigbus:
 #endif
 	current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
 	tsk->thread.cp0_badvaddr = address;
-	info.si_signo = SIGBUS;
-	info.si_errno = 0;
-	info.si_code = BUS_ADRERR;
-	info.si_addr = (void __user *) address;
-	force_sig_info(SIGBUS, &info, tsk);
+	force_sig_fault(SIGBUS, BUS_ADRERR, (void __user *)address, tsk);
 
 	return;
 #ifndef CONFIG_64BIT