aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/net/sff,sfp.txt5
-rw-r--r--drivers/net/phy/phylink.c33
-rw-r--r--drivers/net/phy/sfp-bus.c162
-rw-r--r--drivers/net/phy/sfp.c150
-rw-r--r--include/linux/sfp.h18
5 files changed, 243 insertions, 125 deletions
diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt
index f1c441bedf68..929591d52ed6 100644
--- a/Documentation/devicetree/bindings/net/sff,sfp.txt
+++ b/Documentation/devicetree/bindings/net/sff,sfp.txt
@@ -33,6 +33,10 @@ Optional Properties:
Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
high Tx rate. Must not be present for SFF modules
+- maximum-power-milliwatt : Maximum module power consumption
+ Specifies the maximum power consumption allowable by a module in the
+ slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W.
+
Example #1: Direct serdes to SFP connection
sfp_eth3: sfp-eth3 {
@@ -40,6 +44,7 @@ sfp_eth3: sfp-eth3 {
i2c-bus = <&sfp_1g_i2c>;
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+ maximum-power-milliwatt = <1000>;
pinctrl-names = "default";
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 6ac8b29b2dc3..27327c917a59 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1584,25 +1584,14 @@ static int phylink_sfp_module_insert(void *upstream,
bool changed;
u8 port;
- sfp_parse_support(pl->sfp_bus, id, support);
- port = sfp_parse_port(pl->sfp_bus, id, support);
- iface = sfp_parse_interface(pl->sfp_bus, id);
-
ASSERT_RTNL();
- switch (iface) {
- case PHY_INTERFACE_MODE_SGMII:
- case PHY_INTERFACE_MODE_1000BASEX:
- case PHY_INTERFACE_MODE_2500BASEX:
- case PHY_INTERFACE_MODE_10GKR:
- break;
- default:
- return -EINVAL;
- }
+ sfp_parse_support(pl->sfp_bus, id, support);
+ port = sfp_parse_port(pl->sfp_bus, id, support);
memset(&config, 0, sizeof(config));
linkmode_copy(config.advertising, support);
- config.interface = iface;
+ config.interface = PHY_INTERFACE_MODE_NA;
config.speed = SPEED_UNKNOWN;
config.duplex = DUPLEX_UNKNOWN;
config.pause = MLO_PAUSE_AN;
@@ -1611,6 +1600,22 @@ static int phylink_sfp_module_insert(void *upstream,
/* Ignore errors if we're expecting a PHY to attach later */
ret = phylink_validate(pl, support, &config);
if (ret) {
+ netdev_err(pl->netdev, "validation with support %*pb failed: %d\n",
+ __ETHTOOL_LINK_MODE_MASK_NBITS, support, ret);
+ return ret;
+ }
+
+ iface = sfp_select_interface(pl->sfp_bus, id, config.advertising);
+ if (iface == PHY_INTERFACE_MODE_NA) {
+ netdev_err(pl->netdev,
+ "selection of interface failed, advertisment %*pb\n",
+ __ETHTOOL_LINK_MODE_MASK_NBITS, config.advertising);
+ return -EINVAL;
+ }
+
+ config.interface = iface;
+ ret = phylink_validate(pl, support, &config);
+ if (ret) {
netdev_err(pl->netdev, "validation of %s/%s with support %*pb failed: %d\n",
phylink_an_mode_str(MLO_AN_INBAND),
phy_modes(config.interface),
diff --git a/drivers/net/phy/sfp-bus.c b/drivers/net/phy/sfp-bus.c
index 8961209ee949..3d4ff5d0d2a6 100644
--- a/drivers/net/phy/sfp-bus.c
+++ b/drivers/net/phy/sfp-bus.c
@@ -106,68 +106,6 @@ int sfp_parse_port(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
EXPORT_SYMBOL_GPL(sfp_parse_port);
/**
- * sfp_parse_interface() - Parse the phy_interface_t
- * @bus: a pointer to the &struct sfp_bus structure for the sfp module
- * @id: a pointer to the module's &struct sfp_eeprom_id
- *
- * Derive the phy_interface_t mode for the information found in the
- * module's identifying EEPROM. There is no standard or defined way
- * to derive this information, so we use some heuristics.
- *
- * If the encoding is 64b66b, then the module must be >= 10G, so
- * return %PHY_INTERFACE_MODE_10GKR.
- *
- * If it's 8b10b, then it's 1G or slower. If it's definitely a fibre
- * module, return %PHY_INTERFACE_MODE_1000BASEX mode, otherwise return
- * %PHY_INTERFACE_MODE_SGMII mode.
- *
- * If the encoding is not known, return %PHY_INTERFACE_MODE_NA.
- */
-phy_interface_t sfp_parse_interface(struct sfp_bus *bus,
- const struct sfp_eeprom_id *id)
-{
- phy_interface_t iface;
-
- /* Setting the serdes link mode is guesswork: there's no field in
- * the EEPROM which indicates what mode should be used.
- *
- * If the module wants 64b66b, then it must be >= 10G.
- *
- * If it's a gigabit-only fiber module, it probably does not have
- * a PHY, so switch to 802.3z negotiation mode. Otherwise, switch
- * to SGMII mode (which is required to support non-gigabit speeds).
- */
- switch (id->base.encoding) {
- case SFP_ENCODING_8472_64B66B:
- iface = PHY_INTERFACE_MODE_10GKR;
- break;
-
- case SFP_ENCODING_8B10B:
- if (!id->base.e1000_base_t &&
- !id->base.e100_base_lx &&
- !id->base.e100_base_fx)
- iface = PHY_INTERFACE_MODE_1000BASEX;
- else
- iface = PHY_INTERFACE_MODE_SGMII;
- break;
-
- default:
- if (id->base.e1000_base_cx) {
- iface = PHY_INTERFACE_MODE_1000BASEX;
- break;
- }
-
- iface = PHY_INTERFACE_MODE_NA;
- dev_err(bus->sfp_dev,
- "SFP module encoding does not support 8b10b nor 64b66b\n");
- break;
- }
-
- return iface;
-}
-EXPORT_SYMBOL_GPL(sfp_parse_interface);
-
-/**
* sfp_parse_support() - Parse the eeprom id for supported link modes
* @bus: a pointer to the &struct sfp_bus structure for the sfp module
* @id: a pointer to the module's &struct sfp_eeprom_id
@@ -180,10 +118,7 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
unsigned long *support)
{
unsigned int br_min, br_nom, br_max;
-
- phylink_set(support, Autoneg);
- phylink_set(support, Pause);
- phylink_set(support, Asym_Pause);
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(modes) = { 0, };
/* Decode the bitrate information to MBd */
br_min = br_nom = br_max = 0;
@@ -201,20 +136,20 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
/* Set ethtool support from the compliance fields. */
if (id->base.e10g_base_sr)
- phylink_set(support, 10000baseSR_Full);
+ phylink_set(modes, 10000baseSR_Full);
if (id->base.e10g_base_lr)
- phylink_set(support, 10000baseLR_Full);
+ phylink_set(modes, 10000baseLR_Full);
if (id->base.e10g_base_lrm)
- phylink_set(support, 10000baseLRM_Full);
+ phylink_set(modes, 10000baseLRM_Full);
if (id->base.e10g_base_er)
- phylink_set(support, 10000baseER_Full);
+ phylink_set(modes, 10000baseER_Full);
if (id->base.e1000_base_sx ||
id->base.e1000_base_lx ||
id->base.e1000_base_cx)
- phylink_set(support, 1000baseX_Full);
+ phylink_set(modes, 1000baseX_Full);
if (id->base.e1000_base_t) {
- phylink_set(support, 1000baseT_Half);
- phylink_set(support, 1000baseT_Full);
+ phylink_set(modes, 1000baseT_Half);
+ phylink_set(modes, 1000baseT_Full);
}
/* 1000Base-PX or 1000Base-BX10 */
@@ -228,20 +163,20 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
if ((id->base.sfp_ct_passive || id->base.sfp_ct_active) && br_nom) {
/* This may look odd, but some manufacturers use 12000MBd */
if (br_min <= 12000 && br_max >= 10300)
- phylink_set(support, 10000baseCR_Full);
+ phylink_set(modes, 10000baseCR_Full);
if (br_min <= 3200 && br_max >= 3100)
- phylink_set(support, 2500baseX_Full);
+ phylink_set(modes, 2500baseX_Full);
if (br_min <= 1300 && br_max >= 1200)
- phylink_set(support, 1000baseX_Full);
+ phylink_set(modes, 1000baseX_Full);
}
if (id->base.sfp_ct_passive) {
if (id->base.passive.sff8431_app_e)
- phylink_set(support, 10000baseCR_Full);
+ phylink_set(modes, 10000baseCR_Full);
}
if (id->base.sfp_ct_active) {
if (id->base.active.sff8431_app_e ||
id->base.active.sff8431_lim) {
- phylink_set(support, 10000baseCR_Full);
+ phylink_set(modes, 10000baseCR_Full);
}
}
@@ -249,18 +184,18 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
case 0x00: /* Unspecified */
break;
case 0x02: /* 100Gbase-SR4 or 25Gbase-SR */
- phylink_set(support, 100000baseSR4_Full);
- phylink_set(support, 25000baseSR_Full);
+ phylink_set(modes, 100000baseSR4_Full);
+ phylink_set(modes, 25000baseSR_Full);
break;
case 0x03: /* 100Gbase-LR4 or 25Gbase-LR */
case 0x04: /* 100Gbase-ER4 or 25Gbase-ER */
- phylink_set(support, 100000baseLR4_ER4_Full);
+ phylink_set(modes, 100000baseLR4_ER4_Full);
break;
case 0x0b: /* 100Gbase-CR4 or 25Gbase-CR CA-L */
case 0x0c: /* 25Gbase-CR CA-S */
case 0x0d: /* 25Gbase-CR CA-N */
- phylink_set(support, 100000baseCR4_Full);
- phylink_set(support, 25000baseCR_Full);
+ phylink_set(modes, 100000baseCR4_Full);
+ phylink_set(modes, 25000baseCR_Full);
break;
default:
dev_warn(bus->sfp_dev,
@@ -274,13 +209,70 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
id->base.fc_speed_200 ||
id->base.fc_speed_400) {
if (id->base.br_nominal >= 31)
- phylink_set(support, 2500baseX_Full);
+ phylink_set(modes, 2500baseX_Full);
if (id->base.br_nominal >= 12)
- phylink_set(support, 1000baseX_Full);
+ phylink_set(modes, 1000baseX_Full);
}
+
+ /* If we haven't discovered any modes that this module supports, try
+ * the encoding and bitrate to determine supported modes. Some BiDi
+ * modules (eg, 1310nm/1550nm) are not 1000BASE-BX compliant due to
+ * the differing wavelengths, so do not set any transceiver bits.
+ */
+ if (bitmap_empty(modes, __ETHTOOL_LINK_MODE_MASK_NBITS)) {
+ /* If the encoding and bit rate allows 1000baseX */
+ if (id->base.encoding == SFP_ENCODING_8B10B && br_nom &&
+ br_min <= 1300 && br_max >= 1200)
+ phylink_set(modes, 1000baseX_Full);
+ }
+
+ bitmap_or(support, support, modes, __ETHTOOL_LINK_MODE_MASK_NBITS);
+
+ phylink_set(support, Autoneg);
+ phylink_set(support, Pause);
+ phylink_set(support, Asym_Pause);
}
EXPORT_SYMBOL_GPL(sfp_parse_support);
+/**
+ * sfp_select_interface() - Select appropriate phy_interface_t mode
+ * @bus: a pointer to the &struct sfp_bus structure for the sfp module
+ * @id: a pointer to the module's &struct sfp_eeprom_id
+ * @link_modes: ethtool link modes mask
+ *
+ * Derive the phy_interface_t mode for the information found in the
+ * module's identifying EEPROM and the link modes mask. There is no
+ * standard or defined way to derive this information, so we decide
+ * based upon the link mode mask.
+ */
+phy_interface_t sfp_select_interface(struct sfp_bus *bus,
+ const struct sfp_eeprom_id *id,
+ unsigned long *link_modes)
+{
+ if (phylink_test(link_modes, 10000baseCR_Full) ||
+ phylink_test(link_modes, 10000baseSR_Full) ||
+ phylink_test(link_modes, 10000baseLR_Full) ||
+ phylink_test(link_modes, 10000baseLRM_Full) ||
+ phylink_test(link_modes, 10000baseER_Full))
+ return PHY_INTERFACE_MODE_10GKR;
+
+ if (phylink_test(link_modes, 2500baseX_Full))
+ return PHY_INTERFACE_MODE_2500BASEX;
+
+ if (id->base.e1000_base_t ||
+ id->base.e100_base_lx ||
+ id->base.e100_base_fx)
+ return PHY_INTERFACE_MODE_SGMII;
+
+ if (phylink_test(link_modes, 1000baseX_Full))
+ return PHY_INTERFACE_MODE_1000BASEX;
+
+ dev_warn(bus->sfp_dev, "Unable to ascertain link mode\n");
+
+ return PHY_INTERFACE_MODE_NA;
+}
+EXPORT_SYMBOL_GPL(sfp_select_interface);
+
static LIST_HEAD(sfp_buses);
static DEFINE_MUTEX(sfp_mutex);
diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c
index 6c7d9289078d..83bf4959b043 100644
--- a/drivers/net/phy/sfp.c
+++ b/drivers/net/phy/sfp.c
@@ -42,6 +42,7 @@ enum {
SFP_MOD_EMPTY = 0,
SFP_MOD_PROBE,
+ SFP_MOD_HPOWER,
SFP_MOD_PRESENT,
SFP_MOD_ERROR,
@@ -86,6 +87,7 @@ static const enum gpiod_flags gpio_flags[] = {
* access the I2C EEPROM. However, Avago modules require 300ms.
*/
#define T_PROBE_INIT msecs_to_jiffies(300)
+#define T_HPOWER_LEVEL msecs_to_jiffies(300)
#define T_PROBE_RETRY msecs_to_jiffies(100)
/* SFP modules appear to always have their PHY configured for bus address
@@ -110,10 +112,12 @@ struct sfp {
struct sfp_bus *sfp_bus;
struct phy_device *mod_phy;
const struct sff_data *type;
+ u32 max_power_mW;
unsigned int (*get_state)(struct sfp *);
void (*set_state)(struct sfp *, unsigned int);
int (*read)(struct sfp *, bool, u8, void *, size_t);
+ int (*write)(struct sfp *, bool, u8, void *, size_t);
struct gpio_desc *gpio[GPIO_MAX];
@@ -201,10 +205,11 @@ static void sfp_gpio_set_state(struct sfp *sfp, unsigned int state)
}
}
-static int sfp__i2c_read(struct i2c_adapter *i2c, u8 bus_addr, u8 dev_addr,
- void *buf, size_t len)
+static int sfp_i2c_read(struct sfp *sfp, bool a2, u8 dev_addr, void *buf,
+ size_t len)
{
struct i2c_msg msgs[2];
+ u8 bus_addr = a2 ? 0x51 : 0x50;
int ret;
msgs[0].addr = bus_addr;
@@ -216,17 +221,38 @@ static int sfp__i2c_read(struct i2c_adapter *i2c, u8 bus_addr, u8 dev_addr,
msgs[1].len = len;
msgs[1].buf = buf;
- ret = i2c_transfer(i2c, msgs, ARRAY_SIZE(msgs));
+ ret = i2c_transfer(sfp->i2c, msgs, ARRAY_SIZE(msgs));
if (ret < 0)
return ret;
return ret == ARRAY_SIZE(msgs) ? len : 0;
}
-static int sfp_i2c_read(struct sfp *sfp, bool a2, u8 addr, void *buf,
- size_t len)
+static int sfp_i2c_write(struct sfp *sfp, bool a2, u8 dev_addr, void *buf,
+ size_t len)
{
- return sfp__i2c_read(sfp->i2c, a2 ? 0x51 : 0x50, addr, buf, len);
+ struct i2c_msg msgs[1];
+ u8 bus_addr = a2 ? 0x51 : 0x50;
+ int ret;
+
+ msgs[0].addr = bus_addr;
+ msgs[0].flags = 0;
+ msgs[0].len = 1 + len;
+ msgs[0].buf = kmalloc(1 + len, GFP_KERNEL);
+ if (!msgs[0].buf)
+ return -ENOMEM;
+
+ msgs[0].buf[0] = dev_addr;
+ memcpy(&msgs[0].buf[1], buf, len);
+
+ ret = i2c_transfer(sfp->i2c, msgs, ARRAY_SIZE(msgs));
+
+ kfree(msgs[0].buf);
+
+ if (ret < 0)
+ return ret;
+
+ return ret == ARRAY_SIZE(msgs) ? len : 0;
}
static int sfp_i2c_configure(struct sfp *sfp, struct i2c_adapter *i2c)
@@ -239,6 +265,7 @@ static int sfp_i2c_configure(struct sfp *sfp, struct i2c_adapter *i2c)
sfp->i2c = i2c;
sfp->read = sfp_i2c_read;
+ sfp->write = sfp_i2c_write;
i2c_mii = mdio_i2c_alloc(sfp->dev, i2c);
if (IS_ERR(i2c_mii))
@@ -274,6 +301,11 @@ static int sfp_read(struct sfp *sfp, bool a2, u8 addr, void *buf, size_t len)
return sfp->read(sfp, a2, addr, buf, len);
}
+static int sfp_write(struct sfp *sfp, bool a2, u8 addr, void *buf, size_t len)
+{
+ return sfp->write(sfp, a2, addr, buf, len);
+}
+
static unsigned int sfp_check(void *buf, size_t len)
{
u8 *p, check;
@@ -462,21 +494,83 @@ static void sfp_sm_mod_init(struct sfp *sfp)
sfp_sm_probe_phy(sfp);
}
+static int sfp_sm_mod_hpower(struct sfp *sfp)
+{
+ u32 power;
+ u8 val;
+ int err;
+
+ power = 1000;
+ if (sfp->id.ext.options & cpu_to_be16(SFP_OPTIONS_POWER_DECL))
+ power = 1500;
+ if (sfp->id.ext.options & cpu_to_be16(SFP_OPTIONS_HIGH_POWER_LEVEL))
+ power = 2000;
+
+ if (sfp->id.ext.sff8472_compliance == SFP_SFF8472_COMPLIANCE_NONE &&
+ (sfp->id.ext.diagmon & (SFP_DIAGMON_DDM | SFP_DIAGMON_ADDRMODE)) !=
+ SFP_DIAGMON_DDM) {
+ /* The module appears not to implement bus address 0xa2,
+ * or requires an address change sequence, so assume that
+ * the module powers up in the indicated power mode.
+ */
+ if (power > sfp->max_power_mW) {
+ dev_err(sfp->dev,
+ "Host does not support %u.%uW modules\n",
+ power / 1000, (power / 100) % 10);
+ return -EINVAL;
+ }
+ return 0;
+ }
+
+ if (power > sfp->max_power_mW) {
+ dev_warn(sfp->dev,
+ "Host does not support %u.%uW modules, module left in power mode 1\n",
+ power / 1000, (power / 100) % 10);
+ return 0;
+ }
+
+ if (power <= 1000)
+ return 0;
+
+ err = sfp_read(sfp, true, SFP_EXT_STATUS, &val, sizeof(val));
+ if (err != sizeof(val)) {
+ dev_err(sfp->dev, "Failed to read EEPROM: %d\n", err);
+ err = -EAGAIN;
+ goto err;
+ }
+
+ val |= BIT(0);
+
+ err = sfp_write(sfp, true, SFP_EXT_STATUS, &val, sizeof(val));
+ if (err != sizeof(val)) {
+ dev_err(sfp->dev, "Failed to write EEPROM: %d\n", err);
+ err = -EAGAIN;
+ goto err;
+ }
+
+ dev_info(sfp->dev, "Module switched to %u.%uW power level\n",
+ power / 1000, (power / 100) % 10);
+ return T_HPOWER_LEVEL;
+
+err:
+ return err;
+}
+
static int sfp_sm_mod_probe(struct sfp *sfp)
{
/* SFP module inserted - read I2C data */
struct sfp_eeprom_id id;
u8 check;
- int err;
+ int ret;
- err = sfp_read(sfp, false, 0, &id, sizeof(id));
- if (err < 0) {
- dev_err(sfp->dev, "failed to read EEPROM: %d\n", err);
+ ret = sfp_read(sfp, false, 0, &id, sizeof(id));
+ if (ret < 0) {
+ dev_err(sfp->dev, "failed to read EEPROM: %d\n", ret);
return -EAGAIN;
}
- if (err != sizeof(id)) {
- dev_err(sfp->dev, "EEPROM short read: %d\n", err);
+ if (ret != sizeof(id)) {
+ dev_err(sfp->dev, "EEPROM short read: %d\n", ret);
return -EAGAIN;
}
@@ -521,7 +615,11 @@ static int sfp_sm_mod_probe(struct sfp *sfp)
dev_warn(sfp->dev,
"module address swap to access page 0xA2 is not supported.\n");
- return sfp_module_insert(sfp->sfp_bus, &sfp->id);
+ ret = sfp_module_insert(sfp->sfp_bus, &sfp->id);
+ if (ret < 0)
+ return ret;
+
+ return sfp_sm_mod_hpower(sfp);
}
static void sfp_sm_mod_remove(struct sfp *sfp)
@@ -560,17 +658,25 @@ static void sfp_sm_event(struct sfp *sfp, unsigned int event)
if (event == SFP_E_REMOVE) {
sfp_sm_ins_next(sfp, SFP_MOD_EMPTY, 0);
} else if (event == SFP_E_TIMEOUT) {
- int err = sfp_sm_mod_probe(sfp);
+ int val = sfp_sm_mod_probe(sfp);
- if (err == 0)
+ if (val == 0)
sfp_sm_ins_next(sfp, SFP_MOD_PRESENT, 0);
- else if (err == -EAGAIN)
- sfp_sm_set_timer(sfp, T_PROBE_RETRY);
- else
+ else if (val > 0)
+ sfp_sm_ins_next(sfp, SFP_MOD_HPOWER, val);
+ else if (val != -EAGAIN)
sfp_sm_ins_next(sfp, SFP_MOD_ERROR, 0);
+ else
+ sfp_sm_set_timer(sfp, T_PROBE_RETRY);
}
break;
+ case SFP_MOD_HPOWER:
+ if (event == SFP_E_TIMEOUT) {
+ sfp_sm_ins_next(sfp, SFP_MOD_PRESENT, 0);
+ break;
+ }
+ /* fallthrough */
case SFP_MOD_PRESENT:
case SFP_MOD_ERROR:
if (event == SFP_E_REMOVE) {
@@ -889,6 +995,14 @@ static int sfp_probe(struct platform_device *pdev)
if (!(sfp->gpio[GPIO_MODDEF0]))
sfp->get_state = sff_gpio_get_state;
+ device_property_read_u32(&pdev->dev, "maximum-power-milliwatt",
+ &sfp->max_power_mW);
+ if (!sfp->max_power_mW)
+ sfp->max_power_mW = 1000;
+
+ dev_info(sfp->dev, "Host maximum power %u.%uW\n",
+ sfp->max_power_mW / 1000, (sfp->max_power_mW / 100) % 10);
+
sfp->sfp_bus = sfp_register_socket(sfp->dev, sfp, &sfp_module_ops);
if (!sfp->sfp_bus)
return -ENOMEM;
diff --git a/include/linux/sfp.h b/include/linux/sfp.h
index e724d5a3dd80..ebce9e24906a 100644
--- a/include/linux/sfp.h
+++ b/include/linux/sfp.h
@@ -422,10 +422,11 @@ struct sfp_upstream_ops {
#if IS_ENABLED(CONFIG_SFP)
int sfp_parse_port(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
unsigned long *support);
-phy_interface_t sfp_parse_interface(struct sfp_bus *bus,
- const struct sfp_eeprom_id *id);
void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
unsigned long *support);
+phy_interface_t sfp_select_interface(struct sfp_bus *bus,
+ const struct sfp_eeprom_id *id,
+ unsigned long *link_modes);
int sfp_get_module_info(struct sfp_bus *bus, struct ethtool_modinfo *modinfo);
int sfp_get_module_eeprom(struct sfp_bus *bus, struct ethtool_eeprom *ee,
@@ -444,18 +445,19 @@ static inline int sfp_parse_port(struct sfp_bus *bus,
return PORT_OTHER;
}
-static inline phy_interface_t sfp_parse_interface(struct sfp_bus *bus,
- const struct sfp_eeprom_id *id)
-{
- return PHY_INTERFACE_MODE_NA;
-}
-
static inline void sfp_parse_support(struct sfp_bus *bus,
const struct sfp_eeprom_id *id,
unsigned long *support)
{
}
+static inline phy_interface_t sfp_select_interface(struct sfp_bus *bus,
+ const struct sfp_eeprom_id *id,
+ unsigned long *link_modes)
+{
+ return PHY_INTERFACE_MODE_NA;
+}
+
static inline int sfp_get_module_info(struct sfp_bus *bus,
struct ethtool_modinfo *modinfo)
{