diff options
| -rw-r--r-- | Documentation/tty/device_drivers/oxsemi-tornado.rst | 129 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_pci.c | 339 |
2 files changed, 400 insertions, 68 deletions
diff --git a/Documentation/tty/device_drivers/oxsemi-tornado.rst b/Documentation/tty/device_drivers/oxsemi-tornado.rst new file mode 100644 index 000000000000..0180d8bb0881 --- /dev/null +++ b/Documentation/tty/device_drivers/oxsemi-tornado.rst @@ -0,0 +1,129 @@ +.. SPDX-License-Identifier: GPL-2.0 + +==================================================================== +Notes on Oxford Semiconductor PCIe (Tornado) 950 serial port devices +==================================================================== + +Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven +by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock. + +The baud rate produced by the baud generator is obtained from this input +frequency by dividing it by the clock prescaler, which can be set to any +value from 1 to 63.875 in increments of 0.125, and then the usual 16-bit +divisor is used as with the original 8250, to divide the frequency by a +value from 1 to 65535. Finally a programmable oversampling rate is used +that can take any value from 4 to 16 to divide the frequency further and +determine the actual baud rate used. Baud rates from 15625000bps down +to 0.933bps can be obtained this way. + +By default the oversampling rate is set to 16 and the clock prescaler is +set to 33.875, meaning that the frequency to be used as the reference +for the usual 16-bit divisor is 115313.653, which is close enough to the +frequency of 115200 used by the original 8250 for the same values to be +used for the divisor to obtain the requested baud rates by software that +is unaware of the extra clock controls available. + +The oversampling rate is programmed with the TCR register and the clock +prescaler is programmed with the CPR/CPR2 register pair[1][2][3][4]. +To switch away from the default value of 33.875 for the prescaler the +the enhanced mode has to be explicitly enabled though, by setting bit 4 +of the EFR. In that mode setting bit 7 in the MCR enables the prescaler +or otherwise it is bypassed as if the value of 1 was used. Additionally +writing any value to CPR clears CPR2 for compatibility with old software +written for older conventional PCI Oxford Semiconductor devices that do +not have the extra prescaler's 9th bit in CPR2, so the CPR/CPR2 register +pair has to be programmed in the right order. + +By using these parameters rates from 15625000bps down to 1bps can be +obtained, with either exact or highly-accurate actual bit rates for +standard and many non-standard rates. + +Here are the figures for the standard and some non-standard baud rates +(including those quoted in Oxford Semiconductor documentation), giving +the requested rate (r), the actual rate yielded (a) and its deviation +from the requested rate (d), and the values of the oversampling rate +(tcr), the clock prescaler (cpr) and the divisor (div) produced by the +new `get_divisor' handler: + +r: 15625000, a: 15625000.00, d: 0.0000%, tcr: 4, cpr: 1.000, div: 1 +r: 12500000, a: 12500000.00, d: 0.0000%, tcr: 5, cpr: 1.000, div: 1 +r: 10416666, a: 10416666.67, d: 0.0000%, tcr: 6, cpr: 1.000, div: 1 +r: 8928571, a: 8928571.43, d: 0.0000%, tcr: 7, cpr: 1.000, div: 1 +r: 7812500, a: 7812500.00, d: 0.0000%, tcr: 8, cpr: 1.000, div: 1 +r: 4000000, a: 4000000.00, d: 0.0000%, tcr: 5, cpr: 3.125, div: 1 +r: 3686400, a: 3676470.59, d: -0.2694%, tcr: 8, cpr: 2.125, div: 1 +r: 3500000, a: 3496503.50, d: -0.0999%, tcr: 13, cpr: 1.375, div: 1 +r: 3000000, a: 2976190.48, d: -0.7937%, tcr: 14, cpr: 1.500, div: 1 +r: 2500000, a: 2500000.00, d: 0.0000%, tcr: 10, cpr: 2.500, div: 1 +r: 2000000, a: 2000000.00, d: 0.0000%, tcr: 10, cpr: 3.125, div: 1 +r: 1843200, a: 1838235.29, d: -0.2694%, tcr: 16, cpr: 2.125, div: 1 +r: 1500000, a: 1492537.31, d: -0.4975%, tcr: 5, cpr: 8.375, div: 1 +r: 1152000, a: 1152073.73, d: 0.0064%, tcr: 14, cpr: 3.875, div: 1 +r: 921600, a: 919117.65, d: -0.2694%, tcr: 16, cpr: 2.125, div: 2 +r: 576000, a: 576036.87, d: 0.0064%, tcr: 14, cpr: 3.875, div: 2 +r: 460800, a: 460829.49, d: 0.0064%, tcr: 7, cpr: 3.875, div: 5 +r: 230400, a: 230414.75, d: 0.0064%, tcr: 14, cpr: 3.875, div: 5 +r: 115200, a: 115207.37, d: 0.0064%, tcr: 14, cpr: 1.250, div: 31 +r: 57600, a: 57603.69, d: 0.0064%, tcr: 8, cpr: 3.875, div: 35 +r: 38400, a: 38402.46, d: 0.0064%, tcr: 14, cpr: 3.875, div: 30 +r: 19200, a: 19201.23, d: 0.0064%, tcr: 8, cpr: 3.875, div: 105 +r: 9600, a: 9600.06, d: 0.0006%, tcr: 9, cpr: 1.125, div: 643 +r: 4800, a: 4799.98, d: -0.0004%, tcr: 7, cpr: 2.875, div: 647 +r: 2400, a: 2400.02, d: 0.0008%, tcr: 9, cpr: 2.250, div: 1286 +r: 1200, a: 1200.00, d: 0.0000%, tcr: 14, cpr: 2.875, div: 1294 +r: 300, a: 300.00, d: 0.0000%, tcr: 11, cpr: 2.625, div: 7215 +r: 200, a: 200.00, d: 0.0000%, tcr: 16, cpr: 1.250, div: 15625 +r: 150, a: 150.00, d: 0.0000%, tcr: 13, cpr: 2.250, div: 14245 +r: 134, a: 134.00, d: 0.0000%, tcr: 11, cpr: 2.625, div: 16153 +r: 110, a: 110.00, d: 0.0000%, tcr: 12, cpr: 1.000, div: 47348 +r: 75, a: 75.00, d: 0.0000%, tcr: 4, cpr: 5.875, div: 35461 +r: 50, a: 50.00, d: 0.0000%, tcr: 16, cpr: 1.250, div: 62500 +r: 25, a: 25.00, d: 0.0000%, tcr: 16, cpr: 2.500, div: 62500 +r: 4, a: 4.00, d: 0.0000%, tcr: 16, cpr: 20.000, div: 48828 +r: 2, a: 2.00, d: 0.0000%, tcr: 16, cpr: 40.000, div: 48828 +r: 1, a: 1.00, d: 0.0000%, tcr: 16, cpr: 63.875, div: 61154 + +With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX +limitation imposed by `serial8250_get_baud_rate' standard baud rates +below 300bps become unavailable in the regular way, e.g. the rate of +200bps requires the baud base to be divided by 78125 and that is beyond +the unsigned 16-bit range. The historic spd_cust feature can still be +used by encoding the values for, the prescaler, the oversampling rate +and the clock divisor (DLM/DLL) as follows to obtain such rates if so +required: + + 31 29 28 20 19 16 15 0 ++-----+-----------------+-------+-------------------------------+ +|0 0 0| CPR2:CPR | TCR | DLM:DLL | ++-----+-----------------+-------+-------------------------------+ + +Use a value such encoded for the `custom_divisor' field along with the +ASYNC_SPD_CUST flag set in the `flags' field in `struct serial_struct' +passed with the TIOCSSERIAL ioctl(2), such as with the setserial(8) +utility and its `divisor' and `spd_cust' parameters, and the select +the baud rate of 38400bps. Note that the value of 0 in TCR sets the +oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are +clamped by the driver to 1. + +For example the value of 0x1f4004e2 will set CPR2/CPR, TCR and DLM/DLL +respectively to 0x1f4, 0x0 and 0x04e2, choosing the prescaler value, +the oversampling rate and the clock divisor of 62.500, 16 and 1250 +respectively. These parameters will set the baud rate for the serial +port to 62500000 / 62.500 / 1250 / 16 = 50bps. + +References: + +[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor, + Inc., DS-0045, 10 Nov 2008, Section "950 Mode", pp. 64-65 + +[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port", + Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "950 Mode", + p. 20 + +[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford + Semiconductor, Inc., DS-0047, Feb 08, Section "950 Mode", p. 20 + +[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford + Semiconductor, Inc., DS-0048, Feb 08, Section "950 Mode", p. 20 + +Maciej W. Rozycki <macro@orcam.me.uk> diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index e8be1b3a9597..a17619db7939 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -11,6 +11,7 @@ #include <linux/pci.h> #include <linux/string.h> #include <linux/kernel.h> +#include <linux/math.h> #include <linux/slab.h> #include <linux/delay.h> #include <linux/tty.h> @@ -1044,6 +1045,208 @@ static int pci_oxsemi_tornado_init(struct pci_dev *dev) return number_uarts; } +/* Tornado-specific constants for the TCR and CPR registers; see below. */ +#define OXSEMI_TORNADO_TCR_MASK 0xf +#define OXSEMI_TORNADO_CPR_MASK 0x1ff +#define OXSEMI_TORNADO_CPR_MIN 0x008 +#define OXSEMI_TORNADO_CPR_DEF 0x10f + +/* + * Determine the oversampling rate, the clock prescaler, and the clock + * divisor for the requested baud rate. The clock rate is 62.5 MHz, + * which is four times the baud base, and the prescaler increments in + * steps of 1/8. Therefore to make calculations on integers we need + * to use a scaled clock rate, which is the baud base multiplied by 32 + * (or our assumed UART clock rate multiplied by 2). + * + * The allowed oversampling rates are from 4 up to 16 inclusive (values + * from 0 to 3 inclusive map to 16). Likewise the clock prescaler allows + * values between 1.000 and 63.875 inclusive (operation for values from + * 0.000 to 0.875 has not been specified). The clock divisor is the usual + * unsigned 16-bit integer. + * + * For the most accurate baud rate we use a table of predetermined + * oversampling rates and clock prescalers that records all possible + * products of the two parameters in the range from 4 up to 255 inclusive, + * and additionally 335 for the 1500000bps rate, with the prescaler scaled + * by 8. The table is sorted by the decreasing value of the oversampling + * rate and ties are resolved by sorting by the decreasing value of the + * product. This way preference is given to higher oversampling rates. + * + * We iterate over the table and choose the product of an oversampling + * rate and a clock prescaler that gives the lowest integer division + * result deviation, or if an exact integer divider is found we stop + * looking for it right away. We do some fixup if the resulting clock + * divisor required would be out of its unsigned 16-bit integer range. + * + * Finally we abuse the supposed fractional part returned to encode the + * 4-bit value of the oversampling rate and the 9-bit value of the clock + * prescaler which will end up in the TCR and CPR/CPR2 registers. + */ +static unsigned int pci_oxsemi_tornado_get_divisor(struct uart_port *port, + unsigned int baud, + unsigned int *frac) +{ + static u8 p[][2] = { + { 16, 14, }, { 16, 13, }, { 16, 12, }, { 16, 11, }, + { 16, 10, }, { 16, 9, }, { 16, 8, }, { 15, 17, }, + { 15, 16, }, { 15, 15, }, { 15, 14, }, { 15, 13, }, + { 15, 12, }, { 15, 11, }, { 15, 10, }, { 15, 9, }, + { 15, 8, }, { 14, 18, }, { 14, 17, }, { 14, 14, }, + { 14, 13, }, { 14, 12, }, { 14, 11, }, { 14, 10, }, + { 14, 9, }, { 14, 8, }, { 13, 19, }, { 13, 18, }, + { 13, 17, }, { 13, 13, }, { 13, 12, }, { 13, 11, }, + { 13, 10, }, { 13, 9, }, { 13, 8, }, { 12, 19, }, + { 12, 18, }, { 12, 17, }, { 12, 11, }, { 12, 9, }, + { 12, 8, }, { 11, 23, }, { 11, 22, }, { 11, 21, }, + { 11, 20, }, { 11, 19, }, { 11, 18, }, { 11, 17, }, + { 11, 11, }, { 11, 10, }, { 11, 9, }, { 11, 8, }, + { 10, 25, }, { 10, 23, }, { 10, 20, }, { 10, 19, }, + { 10, 17, }, { 10, 10, }, { 10, 9, }, { 10, 8, }, + { 9, 27, }, { 9, 23, }, { 9, 21, }, { 9, 19, }, + { 9, 18, }, { 9, 17, }, { 9, 9, }, { 9, 8, }, + { 8, 31, }, { 8, 29, }, { 8, 23, }, { 8, 19, }, + { 8, 17, }, { 8, 8, }, { 7, 35, }, { 7, 31, }, + { 7, 29, }, { 7, 25, }, { 7, 23, }, { 7, 21, }, + { 7, 19, }, { 7, 17, }, { 7, 15, }, { 7, 14, }, + { 7, 13, }, { 7, 12, }, { 7, 11, }, { 7, 10, }, + { 7, 9, }, { 7, 8, }, { 6, 41, }, { 6, 37, }, + { 6, 31, }, { 6, 29, }, { 6, 23, }, { 6, 19, }, + { 6, 17, }, { 6, 13, }, { 6, 11, }, { 6, 10, }, + { 6, 9, }, { 6, 8, }, { 5, 67, }, { 5, 47, }, + { 5, 43, }, { 5, 41, }, { 5, 37, }, { 5, 31, }, + { 5, 29, }, { 5, 25, }, { 5, 23, }, { 5, 19, }, + { 5, 17, }, { 5, 15, }, { 5, 13, }, { 5, 11, }, + { 5, 10, }, { 5, 9, }, { 5, 8, }, { 4, 61, }, + { 4, 59, }, { 4, 53, }, { 4, 47, }, { 4, 43, }, + { 4, 41, }, { 4, 37, }, { 4, 31, }, { 4, 29, }, + { 4, 23, }, { 4, 19, }, { 4, 17, }, { 4, 13, }, + { 4, 9, }, { 4, 8, }, + }; + /* Scale the quotient for comparison to get the fractional part. */ + const unsigned int quot_scale = 65536; + unsigned int sclk = port->uartclk * 2; + unsigned int sdiv = DIV_ROUND_CLOSEST(sclk, baud); + unsigned int best_squot; + unsigned int squot; + unsigned int quot; + u16 cpr; + u8 tcr; + int i; + + /* Old custom speed handling. */ + if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) { + unsigned int cust_div = port->custom_divisor; + + quot = cust_div & UART_DIV_MAX; + tcr = (cust_div >> 16) & OXSEMI_TORNADO_TCR_MASK; + cpr = (cust_div >> 20) & OXSEMI_TORNADO_CPR_MASK; + if (cpr < OXSEMI_TORNADO_CPR_MIN) + cpr = OXSEMI_TORNADO_CPR_DEF; + } else { + best_squot = quot_scale; + for (i = 0; i < ARRAY_SIZE(p); i++) { + unsigned int spre; + unsigned int srem; + u8 cp; + u8 tc; + + tc = p[i][0]; + cp = p[i][1]; + spre = tc * cp; + + srem = sdiv % spre; + if (srem > spre / 2) + srem = spre - srem; + squot = DIV_ROUND_CLOSEST(srem * quot_scale, spre); + + if (srem == 0) { + tcr = tc; + cpr = cp; + quot = sdiv / spre; + break; + } else if (squot < best_squot) { + best_squot = squot; + tcr = tc; + cpr = cp; + quot = DIV_ROUND_CLOSEST(sdiv, spre); + } + } + while (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1 && + quot % 2 == 0) { + quot >>= 1; + tcr <<= 1; + } + while (quot > UART_DIV_MAX) { + if (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1) { + quot >>= 1; + tcr <<= 1; + } else if (cpr <= OXSEMI_TORNADO_CPR_MASK >> 1) { + quot >>= 1; + cpr <<= 1; + } else { + quot = quot * cpr / OXSEMI_TORNADO_CPR_MASK; + cpr = OXSEMI_TORNADO_CPR_MASK; + } + } + } + + *frac = (cpr << 8) | (tcr & OXSEMI_TORNADO_TCR_MASK); + return quot; +} + +/* + * Set the oversampling rate in the transmitter clock cycle register (TCR), + * the clock prescaler in the clock prescaler register (CPR and CPR2), and + * the clock divisor in the divisor latch (DLL and DLM). Note that for + * backwards compatibility any write to CPR clears CPR2 and therefore CPR + * has to be written first, followed by CPR2, which occupies the location + * of CKS used with earlier UART designs. + */ +static void pci_oxsemi_tornado_set_divisor(struct uart_port *port, + unsigned int baud, + unsigned int quot, + unsigned int quot_frac) +{ + struct uart_8250_port *up = up_to_u8250p(port); + u8 cpr2 = quot_frac >> 16; + u8 cpr = quot_frac >> 8; + u8 tcr = quot_frac; + + serial_icr_write(up, UART_TCR, tcr); + serial_icr_write(up, UART_CPR, cpr); + serial_icr_write(up, UART_CKS, cpr2); + serial8250_do_set_divisor(port, baud, quot, 0); +} + +/* + * For Tornado devices we force MCR[7] set for the Divide-by-M N/8 baud rate + * generator prescaler (CPR and CPR2). Otherwise no prescaler would be used. + */ +static void pci_oxsemi_tornado_set_mctrl(struct uart_port *port, + unsigned int mctrl) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + up->mcr |= UART_MCR_CLKSEL; + serial8250_do_set_mctrl(port, mctrl); +} + +static int pci_oxsemi_tornado_setup(struct serial_private *priv, + const struct pciserial_board *board, + struct uart_8250_port *up, int idx) +{ + struct pci_dev *dev = priv->dev; + + if (pci_oxsemi_tornado_p(dev)) { + up->port.get_divisor = pci_oxsemi_tornado_get_divisor; + up->port.set_divisor = pci_oxsemi_tornado_set_divisor; + up->port.set_mctrl = pci_oxsemi_tornado_set_mctrl; + } + + return pci_default_setup(priv, board, up, idx); +} + static int pci_asix_setup(struct serial_private *priv, const struct pciserial_board *board, struct uart_8250_port *port, int idx) @@ -2245,7 +2448,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = { .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, .init = pci_oxsemi_tornado_init, - .setup = pci_default_setup, + .setup = pci_oxsemi_tornado_setup, }, { .vendor = PCI_VENDOR_ID_MAINPINE, @@ -2253,7 +2456,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = { .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, .init = pci_oxsemi_tornado_init, - .setup = pci_default_setup, + .setup = pci_oxsemi_tornado_setup, }, { .vendor = PCI_VENDOR_ID_DIGI, @@ -2261,7 +2464,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = { .subvendor = PCI_SUBVENDOR_ID_IBM, .subdevice = PCI_ANY_ID, .init = pci_oxsemi_tornado_init, - .setup = pci_default_setup, + .setup = pci_oxsemi_tornado_setup, }, { .vendor = PCI_VENDOR_ID_INTEL, @@ -2578,7 +2781,7 @@ enum pci_board_num_t { pbn_b0_2_1843200, pbn_b0_4_1843200, - pbn_b0_1_3906250, + pbn_b0_1_15625000, pbn_b0_bt_1_115200, pbn_b0_bt_2_115200, @@ -2657,10 +2860,10 @@ enum pci_board_num_t { pbn_panacom4, pbn_plx_romulus, pbn_oxsemi, - pbn_oxsemi_1_3906250, - pbn_oxsemi_2_3906250, - pbn_oxsemi_4_3906250, - pbn_oxsemi_8_3906250, + pbn_oxsemi_1_15625000, + pbn_oxsemi_2_15625000, + pbn_oxsemi_4_15625000, + pbn_oxsemi_8_15625000, pbn_intel_i960, pbn_sgi_ioc3, pbn_computone_4, @@ -2803,10 +3006,10 @@ static struct pciserial_board pci_boards[] = { .uart_offset = 8, }, - [pbn_b0_1_3906250] = { + [pbn_b0_1_15625000] = { .flags = FL_BASE0, .num_ports = 1, - .base_baud = 3906250, + .base_baud = 15625000, .uart_offset = 8, }, @@ -3187,31 +3390,31 @@ static struct pciserial_board pci_boards[] = { .base_baud = 115200, .uart_offset = 8, }, - [pbn_oxsemi_1_3906250] = { + [pbn_oxsemi_1_15625000] = { .flags = FL_BASE0, .num_ports = 1, - .base_baud = 3906250, + .base_baud = 15625000, .uart_offset = 0x200, .first_offset = 0x1000, }, - [pbn_oxsemi_2_3906250] = { + [pbn_oxsemi_2_15625000] = { .flags = FL_BASE0, .num_ports = 2, - .base_baud = 3906250, + .base_baud = 15625000, .uart_offset = 0x200, .first_offset = 0x1000, }, - [pbn_oxsemi_4_3906250] = { + [pbn_oxsemi_4_15625000] = { .flags = FL_BASE0, .num_ports = 4, - .base_baud = 3906250, + .base_baud = 15625000, .uart_offset = 0x200, .first_offset = 0x1000, }, - [pbn_oxsemi_8_3906250] = { + [pbn_oxsemi_8_15625000] = { .flags = FL_BASE0, .num_ports = 8, - .base_baud = 3906250, + .base_baud = 15625000, .uart_offset = 0x200, .first_offset = 0x1000, }, @@ -4205,165 +4408,165 @@ static const struct pci_device_id serial_pci_tbl[] = { */ { PCI_VENDOR_ID_OXSEMI, 0xc101, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc105, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc11b, /* OXPCIe952 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc11f, /* OXPCIe952 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc120, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc124, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc138, /* OXPCIe952 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc13d, /* OXPCIe952 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc140, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc141, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc144, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc145, /* OXPCIe952 1 Legacy UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_b0_1_3906250 }, + pbn_b0_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc158, /* OXPCIe952 2 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_2_3906250 }, + pbn_oxsemi_2_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc15d, /* OXPCIe952 2 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_2_3906250 }, + pbn_oxsemi_2_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc208, /* OXPCIe954 4 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_4_3906250 }, + pbn_oxsemi_4_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc20d, /* OXPCIe954 4 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_4_3906250 }, + pbn_oxsemi_4_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc308, /* OXPCIe958 8 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_8_3906250 }, + pbn_oxsemi_8_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc30d, /* OXPCIe958 8 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_8_3906250 }, + pbn_oxsemi_8_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc40b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc40f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc41b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc41f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc42b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc42f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc43b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc43f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc44b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc44f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc45b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc45f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc46b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc46f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc47b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc47f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc48b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc48f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc49b, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc49f, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc4ab, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc4af, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc4bb, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc4bf, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc4cb, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_OXSEMI, 0xc4cf, /* OXPCIe200 1 Native UART */ PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, /* * Mainpine Inc. IQ Express "Rev3" utilizing OxSemi Tornado */ { PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 1 Port V.34 Super-G3 Fax */ PCI_VENDOR_ID_MAINPINE, 0x4001, 0, 0, - pbn_oxsemi_1_3906250 }, + pbn_oxsemi_1_15625000 }, { PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 2 Port V.34 Super-G3 Fax */ PCI_VENDOR_ID_MAINPINE, 0x4002, 0, 0, - pbn_oxsemi_2_3906250 }, + pbn_oxsemi_2_15625000 }, { PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 4 Port V.34 Super-G3 Fax */ PCI_VENDOR_ID_MAINPINE, 0x4004, 0, 0, - pbn_oxsemi_4_3906250 }, + pbn_oxsemi_4_15625000 }, { PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 8 Port V.34 Super-G3 Fax */ PCI_VENDOR_ID_MAINPINE, 0x4008, 0, 0, - pbn_oxsemi_8_3906250 }, + pbn_oxsemi_8_15625000 }, /* * Digi/IBM PCIe 2-port Async EIA-232 Adapter utilizing OxSemi Tornado */ { PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_2_OX_IBM, PCI_SUBVENDOR_ID_IBM, PCI_ANY_ID, 0, 0, - pbn_oxsemi_2_3906250 }, + pbn_oxsemi_2_15625000 }, /* * EndRun Technologies. PCI express device range. * EndRun PTP/1588 has 2 Native UARTs utilizing OxSemi 952. */ { PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588, PCI_ANY_ID, PCI_ANY_ID, 0, 0, - pbn_oxsemi_2_3906250 }, + pbn_oxsemi_2_15625000 }, /* * SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards, |