diff options
Diffstat (limited to 'Documentation/ABI/testing/sysfs-class-hwmon')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-class-hwmon | 949 |
1 files changed, 949 insertions, 0 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-hwmon b/Documentation/ABI/testing/sysfs-class-hwmon new file mode 100644 index 000000000000..7271781a23b2 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-hwmon @@ -0,0 +1,949 @@ +What: /sys/class/hwmon/hwmonX/name +Description: + The chip name. + This should be a short, lowercase string, not containing + whitespace, dashes, or the wildcard character '*'. + This attribute represents the chip name. It is the only + mandatory attribute. + I2C devices get this attribute created automatically. + + RO + +What: /sys/class/hwmon/hwmonX/label +Description: + A descriptive label that allows to uniquely identify a + device within the system. + The contents of the label are free-form. + + RO + +What: /sys/class/hwmon/hwmonX/update_interval +Description: + The interval at which the chip will update readings. + Unit: millisecond + + RW + + Some devices have a variable update rate or interval. + This attribute can be used to change it to the desired value. + +What: /sys/class/hwmon/hwmonX/inY_min +Description: + Voltage min value. + + Unit: millivolt + + RW + +What: /sys/class/hwmon/hwmonX/inY_lcrit +Description: + Voltage critical min value. + + Unit: millivolt + + RW + + If voltage drops to or below this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + +What: /sys/class/hwmon/hwmonX/inY_max +Description: + Voltage max value. + + Unit: millivolt + + RW + +What: /sys/class/hwmon/hwmonX/inY_crit +Description: + Voltage critical max value. + + Unit: millivolt + + RW + + If voltage reaches or exceeds this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + +What: /sys/class/hwmon/hwmonX/inY_input +Description: + Voltage input value. + + Unit: millivolt + + RO + + Voltage measured on the chip pin. + + Actual voltage depends on the scaling resistors on the + motherboard, as recommended in the chip datasheet. + + This varies by chip and by motherboard. + Because of this variation, values are generally NOT scaled + by the chip driver, and must be done by the application. + However, some drivers (notably lm87 and via686a) + do scale, because of internal resistors built into a chip. + These drivers will output the actual voltage. Rule of + thumb: drivers should report the voltage values at the + "pins" of the chip. + +What: /sys/class/hwmon/hwmonX/inY_average +Description: + Average voltage + + Unit: millivolt + + RO + +What: /sys/class/hwmon/hwmonX/inY_lowest +Description: + Historical minimum voltage + + Unit: millivolt + + RO + +What: /sys/class/hwmon/hwmonX/inY_highest +Description: + Historical maximum voltage + + Unit: millivolt + + RO + +What: /sys/class/hwmon/hwmonX/inY_reset_history +Description: + Reset inX_lowest and inX_highest + + WO + +What: /sys/class/hwmon/hwmonX/in_reset_history +Description: + Reset inX_lowest and inX_highest for all sensors + + WO + +What: /sys/class/hwmon/hwmonX/inY_label +Description: + Suggested voltage channel label. + + Text string + + Should only be created if the driver has hints about what + this voltage channel is being used for, and user-space + doesn't. In all other cases, the label is provided by + user-space. + + RO + +What: /sys/class/hwmon/hwmonX/inY_enable +Description: + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/cpuY_vid +Description: + CPU core reference voltage. + + Unit: millivolt + + RO + + Not always correct. + +What: /sys/class/hwmon/hwmonX/vrm +Description: + Voltage Regulator Module version number. + + RW (but changing it should no more be necessary) + + Originally the VRM standard version multiplied by 10, but now + an arbitrary number, as not all standards have a version + number. + + Affects the way the driver calculates the CPU core reference + voltage from the vid pins. + +What: /sys/class/hwmon/hwmonX/inY_rated_min +Description: + Minimum rated voltage. + + Unit: millivolt + + RO + +What: /sys/class/hwmon/hwmonX/inY_rated_max +Description: + Maximum rated voltage. + + Unit: millivolt + + RO + +What: /sys/class/hwmon/hwmonX/fanY_min +Description: + Fan minimum value + + Unit: revolution/min (RPM) + + RW + +What: /sys/class/hwmon/hwmonX/fanY_max +Description: + Fan maximum value + + Unit: revolution/min (RPM) + + Only rarely supported by the hardware. + RW + +What: /sys/class/hwmon/hwmonX/fanY_input +Description: + Fan input value. + + Unit: revolution/min (RPM) + + RO + +What: /sys/class/hwmon/hwmonX/fanY_div +Description: + Fan divisor. + + Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128). + + RW + + Some chips only support values 1, 2, 4 and 8. + Note that this is actually an internal clock divisor, which + affects the measurable speed range, not the read value. + +What: /sys/class/hwmon/hwmonX/fanY_pulses +Description: + Number of tachometer pulses per fan revolution. + + Integer value, typically between 1 and 4. + + RW + + This value is a characteristic of the fan connected to the + device's input, so it has to be set in accordance with the fan + model. + + Should only be created if the chip has a register to configure + the number of pulses. In the absence of such a register (and + thus attribute) the value assumed by all devices is 2 pulses + per fan revolution. + +What: /sys/class/hwmon/hwmonX/fanY_target +Description: + Desired fan speed + + Unit: revolution/min (RPM) + + RW + + Only makes sense if the chip supports closed-loop fan speed + control based on the measured fan speed. + +What: /sys/class/hwmon/hwmonX/fanY_label +Description: + Suggested fan channel label. + + Text string + + Should only be created if the driver has hints about what + this fan channel is being used for, and user-space doesn't. + In all other cases, the label is provided by user-space. + + RO + +What: /sys/class/hwmon/hwmonX/fanY_enable +Description: + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/pwmY +Description: + Pulse width modulation fan control. + + Integer value in the range 0 to 255 + + RW + + 255 is max or 100%. + +What: /sys/class/hwmon/hwmonX/pwmY_enable +Description: + Fan speed control method: + + - 0: no fan speed control (i.e. fan at full speed) + - 1: manual fan speed control enabled (using `pwmY`) + - 2+: automatic fan speed control enabled + + Check individual chip documentation files for automatic mode + details. + + RW + +What: /sys/class/hwmon/hwmonX/pwmY_mode +Description: + - 0: DC mode (direct current) + - 1: PWM mode (pulse-width modulation) + + RW + +What: /sys/class/hwmon/hwmonX/pwmY_freq +Description: + Base PWM frequency in Hz. + + Only possibly available when pwmN_mode is PWM, but not always + present even then. + + RW + +What: /sys/class/hwmon/hwmonX/pwmY_auto_channels_temp +Description: + Select which temperature channels affect this PWM output in + auto mode. + + Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc... + Which values are possible depend on the chip used. + + RW + +What: /sys/class/hwmon/hwmonX/pwmY_auto_pointZ_pwm +What: /sys/class/hwmon/hwmonX/pwmY_auto_pointZ_temp +What: /sys/class/hwmon/hwmonX/pwmY_auto_pointZ_temp_hyst +Description: + Define the PWM vs temperature curve. + + Number of trip points is chip-dependent. Use this for chips + which associate trip points to PWM output channels. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_auto_pointZ_pwm +What: /sys/class/hwmon/hwmonX/tempY_auto_pointZ_temp +What: /sys/class/hwmon/hwmonX/tempY_auto_pointZ_temp_hyst +Description: + Define the PWM vs temperature curve. + + Number of trip points is chip-dependent. Use this for chips + which associate trip points to temperature channels. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_type +Description: + Sensor type selection. + + Integers 1 to 6 + + RW + + - 1: CPU embedded diode + - 2: 3904 transistor + - 3: thermal diode + - 4: thermistor + - 5: AMD AMDSI + - 6: Intel PECI + + Not all types are supported by all chips + +What: /sys/class/hwmon/hwmonX/tempY_max +Description: + Temperature max value. + + Unit: millidegree Celsius (or millivolt, see below) + + RW + +What: /sys/class/hwmon/hwmonX/tempY_min +Description: + Temperature min value. + + Unit: millidegree Celsius + + RW + +What: /sys/class/hwmon/hwmonX/tempY_max_hyst +Description: + Temperature hysteresis value for max limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the max value. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_min_hyst +Description: + Temperature hysteresis value for min limit. + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the min value. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_input +Description: + Temperature input value. + + Unit: millidegree Celsius + + RO + +What: /sys/class/hwmon/hwmonX/tempY_crit +Description: + Temperature critical max value, typically greater than + corresponding temp_max values. + + Unit: millidegree Celsius + + RW + +What: /sys/class/hwmon/hwmonX/tempY_crit_alarm +Description: + Critical high temperature alarm flag. + + - 0: OK + - 1: temperature has reached tempY_crit + + RW + + Contrary to regular alarm flags which clear themselves + automatically when read, this one sticks until cleared by + the user. This is done by writing 0 to the file. Writing + other values is unsupported. + +What: /sys/class/hwmon/hwmonX/tempY_crit_hyst +Description: + Temperature hysteresis value for critical limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the critical value. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_emergency +Description: + Temperature emergency max value, for chips supporting more than + two upper temperature limits. Must be equal or greater than + corresponding temp_crit values. + + Unit: millidegree Celsius + + RW + +What: /sys/class/hwmon/hwmonX/tempY_emergency_hyst +Description: + Temperature hysteresis value for emergency limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the emergency value. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_lcrit +Description: + Temperature critical min value, typically lower than + corresponding temp_min values. + + Unit: millidegree Celsius + + RW + +What: /sys/class/hwmon/hwmonX/tempY_lcrit_hyst +Description: + Temperature hysteresis value for critical min limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the critical min value. + + RW + +What: /sys/class/hwmon/hwmonX/tempY_offset +Description: + Temperature offset which is added to the temperature reading + by the chip. + + Unit: millidegree Celsius + + Read/Write value. + +What: /sys/class/hwmon/hwmonX/tempY_label +Description: + Suggested temperature channel label. + + Text string + + Should only be created if the driver has hints about what + this temperature channel is being used for, and user-space + doesn't. In all other cases, the label is provided by + user-space. + + RO + +What: /sys/class/hwmon/hwmonX/tempY_lowest +Description: + Historical minimum temperature + + Unit: millidegree Celsius + + RO + +What: /sys/class/hwmon/hwmonX/tempY_highest +Description: + Historical maximum temperature + + Unit: millidegree Celsius + + RO + +What: /sys/class/hwmon/hwmonX/tempY_reset_history +Description: + Reset temp_lowest and temp_highest + + WO + +What: /sys/class/hwmon/hwmonX/temp_reset_history +Description: + Reset temp_lowest and temp_highest for all sensors + + WO + +What: /sys/class/hwmon/hwmonX/tempY_enable +Description: + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/tempY_rated_min +Description: + Minimum rated temperature. + + Unit: millidegree Celsius + + RO + +What: /sys/class/hwmon/hwmonX/tempY_rated_max +Description: + Maximum rated temperature. + + Unit: millidegree Celsius + + RO + +What: /sys/class/hwmon/hwmonX/currY_max +Description: + Current max value + + Unit: milliampere + + RW + +What: /sys/class/hwmon/hwmonX/currY_min +Description: + Current min value. + + Unit: milliampere + + RW + +What: /sys/class/hwmon/hwmonX/currY_lcrit +Description: + Current critical low value + + Unit: milliampere + + RW + +What: /sys/class/hwmon/hwmonX/currY_crit +Description: + Current critical high value. + + Unit: milliampere + + RW + +What: /sys/class/hwmon/hwmonX/currY_input +Description: + Current input value + + Unit: milliampere + + RO + +What: /sys/class/hwmon/hwmonX/currY_average +Description: + Average current use + + Unit: milliampere + + RO + +What: /sys/class/hwmon/hwmonX/currY_lowest +Description: + Historical minimum current + + Unit: milliampere + + RO + +What: /sys/class/hwmon/hwmonX/currY_highest +Description: + Historical maximum current + Unit: milliampere + RO + +What: /sys/class/hwmon/hwmonX/currY_reset_history +Description: + Reset currX_lowest and currX_highest + + WO + +What: /sys/class/hwmon/hwmonX/curr_reset_history +Description: + Reset currX_lowest and currX_highest for all sensors + + WO + +What: /sys/class/hwmon/hwmonX/currY_enable +Description: + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/currY_rated_min +Description: + Minimum rated current. + + Unit: milliampere + + RO + +What: /sys/class/hwmon/hwmonX/currY_rated_max +Description: + Maximum rated current. + + Unit: milliampere + + RO + +What: /sys/class/hwmon/hwmonX/powerY_average +Description: + Average power use + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_average_interval +Description: + Power use averaging interval. A poll + notification is sent to this file if the + hardware changes the averaging interval. + + Unit: milliseconds + + RW + +What: /sys/class/hwmon/hwmonX/powerY_average_interval_max +Description: + Maximum power use averaging interval + + Unit: milliseconds + + RO + +What: /sys/class/hwmon/hwmonX/powerY_average_interval_min +Description: + Minimum power use averaging interval + + Unit: milliseconds + + RO + +What: /sys/class/hwmon/hwmonX/powerY_average_highest +Description: + Historical average maximum power use + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_average_lowest +Description: + Historical average minimum power use + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_average_max +Description: + A poll notification is sent to + `powerY_average` when power use + rises above this value. + + Unit: microWatt + + RW + +What: /sys/class/hwmon/hwmonX/powerY_average_min +Description: + A poll notification is sent to + `powerY_average` when power use + sinks below this value. + + Unit: microWatt + + RW + +What: /sys/class/hwmon/hwmonX/powerY_input +Description: + Instantaneous power use + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_input_highest +Description: + Historical maximum power use + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_input_lowest +Description: + Historical minimum power use + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_reset_history +Description: + Reset input_highest, input_lowest, + average_highest and average_lowest. + + WO + +What: /sys/class/hwmon/hwmonX/powerY_accuracy +Description: + Accuracy of the power meter. + + Unit: Percent + + RO + +What: /sys/class/hwmon/hwmonX/powerY_cap +Description: + If power use rises above this limit, the + system should take action to reduce power use. + A poll notification is sent to this file if the + cap is changed by the hardware. The `*_cap` + files only appear if the cap is known to be + enforced by hardware. + + Unit: microWatt + + RW + +What: /sys/class/hwmon/hwmonX/powerY_cap_hyst +Description: + Margin of hysteresis built around capping and + notification. + + Unit: microWatt + + RW + +What: /sys/class/hwmon/hwmonX/powerY_cap_max +Description: + Maximum cap that can be set. + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_cap_min +Description: + Minimum cap that can be set. + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_max +Description: + Maximum power. + + Unit: microWatt + + RW + +What: /sys/class/hwmon/hwmonX/powerY_crit +Description: + Critical maximum power. + + If power rises to or above this limit, the + system is expected take drastic action to reduce + power consumption, such as a system shutdown or + a forced powerdown of some devices. + + Unit: microWatt + + RW + +What: /sys/class/hwmon/hwmonX/powerY_enable +Description: + Enable or disable the sensors. + + When disabled the sensor read will return + -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/powerY_rated_min +Description: + Minimum rated power. + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/powerY_rated_max +Description: + Maximum rated power. + + Unit: microWatt + + RO + +What: /sys/class/hwmon/hwmonX/energyY_input +Description: + Cumulative energy use + + Unit: microJoule + + RO + +What: /sys/class/hwmon/hwmonX/energyY_enable +Description: + Enable or disable the sensors. + + When disabled the sensor read will return + -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/humidityY_input +Description: + Humidity + + Unit: milli-percent (per cent mille, pcm) + + RO + + +What: /sys/class/hwmon/hwmonX/humidityY_enable +Description: + Enable or disable the sensors + + When disabled the sensor read will return + -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +What: /sys/class/hwmon/hwmonX/humidityY_rated_min +Description: + Minimum rated humidity. + + Unit: milli-percent (per cent mille, pcm) + + RO + +What: /sys/class/hwmon/hwmonX/humidityY_rated_max +Description: + Maximum rated humidity. + + Unit: milli-percent (per cent mille, pcm) + + RO + + +What: /sys/class/hwmon/hwmonX/intrusionY_alarm +Description: + Chassis intrusion detection + + - 0: OK + - 1: intrusion detected + + RW + + Contrary to regular alarm flags which clear themselves + automatically when read, this one sticks until cleared by + the user. This is done by writing 0 to the file. Writing + other values is unsupported. + +What: /sys/class/hwmon/hwmonX/intrusionY_beep +Description: + Chassis intrusion beep + + - 0: disable + - 1: enable + + RW + +What: /sys/class/hwmon/hwmonX/device/pec +Description: + PEC support on I2C devices + + - 0, off, n: disable + - 1, on, y: enable + + RW |