diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 73 |
1 files changed, 53 insertions, 20 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index bdb22006f713..828d11441ebf 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -287,13 +287,21 @@ do not want to use tracing_snapshot_alloc() as it needs to be done where GFP_KERNEL allocations are allowed. + allow_mismatched_32bit_el0 [ARM64] + Allow execve() of 32-bit applications and setting of the + PER_LINUX32 personality on systems where only a strict + subset of the CPUs support 32-bit EL0. When this + parameter is present, the set of CPUs supporting 32-bit + EL0 is indicated by /sys/devices/system/cpu/aarch32_el0 + and hot-unplug operations may be restricted. + + See Documentation/arm64/asymmetric-32bit.rst for more + information. + amd_iommu= [HW,X86-64] Pass parameters to the AMD IOMMU driver in the system. Possible values are: - fullflush - enable flushing of IO/TLB entries when - they are unmapped. Otherwise they are - flushed before they will be reused, which - is a lot of faster + fullflush - Deprecated, equivalent to iommu.strict=1 off - do not initialize any AMD IOMMU found in the system force_isolation - Force device isolation for all @@ -380,6 +388,9 @@ arm64.nopauth [ARM64] Unconditionally disable Pointer Authentication support + arm64.nomte [ARM64] Unconditionally disable Memory Tagging Extension + support + ataflop= [HW,M68k] atarimouse= [HW,MOUSE] Atari Mouse @@ -1944,18 +1955,17 @@ this case, gfx device will use physical address for DMA. strict [Default Off] - With this option on every unmap_single operation will - result in a hardware IOTLB flush operation as opposed - to batching them for performance. + Deprecated, equivalent to iommu.strict=1. sp_off [Default Off] By default, super page will be supported if Intel IOMMU has the capability. With this option, super page will not be supported. - sm_on [Default Off] - By default, scalable mode will be disabled even if the - hardware advertises that it has support for the scalable - mode translation. With this option set, scalable mode - will be used on hardware which claims to support it. + sm_on + Enable the Intel IOMMU scalable mode if the hardware + advertises that it has support for the scalable mode + translation. + sm_off + Disallow use of the Intel IOMMU scalable mode. tboot_noforce [Default Off] Do not force the Intel IOMMU enabled under tboot. By default, tboot will force Intel IOMMU on, which @@ -2047,13 +2057,12 @@ throughput at the cost of reduced device isolation. Will fall back to strict mode if not supported by the relevant IOMMU driver. - 1 - Strict mode (default). + 1 - Strict mode. DMA unmap operations invalidate IOMMU hardware TLBs synchronously. - Note: on x86, the default behaviour depends on the - equivalent driver-specific parameters, but a strict - mode explicitly specified by either method takes - precedence. + unset - Use value of CONFIG_IOMMU_DEFAULT_DMA_{LAZY,STRICT}. + Note: on x86, strict mode specified via one of the + legacy driver-specific options takes precedence. iommu.passthrough= [ARM64, X86] Configure DMA to bypass the IOMMU by default. @@ -2421,6 +2430,23 @@ feature (tagged TLBs) on capable Intel chips. Default is 1 (enabled) + l1d_flush= [X86,INTEL] + Control mitigation for L1D based snooping vulnerability. + + Certain CPUs are vulnerable to an exploit against CPU + internal buffers which can forward information to a + disclosure gadget under certain conditions. + + In vulnerable processors, the speculatively + forwarded data can be used in a cache side channel + attack, to access data to which the attacker does + not have direct access. + + This parameter controls the mitigation. The + options are: + + on - enable the interface for the mitigation + l1tf= [X86] Control mitigation of the L1TF vulnerability on affected CPUs @@ -4167,6 +4193,15 @@ Format: <bool> (1/Y/y=enable, 0/N/n=disable) default: disabled + printk.console_no_auto_verbose= + Disable console loglevel raise on oops, panic + or lockdep-detected issues (only if lock debug is on). + With an exception to setups with low baudrate on + serial console, keeping this 0 is a good choice + in order to provide more debug information. + Format: <bool> + default: 0 (auto_verbose is enabled) + printk.devkmsg={on,off,ratelimit} Control writing to /dev/kmsg. on - unlimited logging to /dev/kmsg from userspace @@ -4777,7 +4812,7 @@ reboot= [KNL] Format (x86 or x86_64): - [w[arm] | c[old] | h[ard] | s[oft] | g[pio]] \ + [w[arm] | c[old] | h[ard] | s[oft] | g[pio]] | d[efault] \ [[,]s[mp]#### \ [[,]b[ios] | a[cpi] | k[bd] | t[riple] | e[fi] | p[ci]] \ [[,]f[orce] @@ -4945,8 +4980,6 @@ sa1100ir [NET] See drivers/net/irda/sa1100_ir.c. - sbni= [NET] Granch SBNI12 leased line adapter - sched_verbose [KNL] Enables verbose scheduler debug messages. schedstats= [KNL,X86] Enable or disable scheduled statistics. |