diff options
Diffstat (limited to 'Documentation/admin-guide')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 209 | ||||
| -rw-r--r-- | Documentation/admin-guide/media/vimc.dot | 14 | ||||
| -rw-r--r-- | Documentation/admin-guide/sysctl/kernel.rst | 8 |
3 files changed, 183 insertions, 48 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 53c0144e150b..a9066cfb85a0 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -564,12 +564,17 @@ cio_ignore= [S390] See Documentation/s390/common_io.rst for details. - clearcpuid=BITNUM[,BITNUM...] [X86] + clearcpuid=X[,X...] [X86] Disable CPUID feature X for the kernel. See arch/x86/include/asm/cpufeatures.h for the valid bit - numbers. Note the Linux specific bits are not necessarily - stable over kernel options, but the vendor specific + numbers X. Note the Linux-specific bits are not necessarily + stable over kernel options, but the vendor-specific ones should be. + X can also be a string as appearing in the flags: line + in /proc/cpuinfo which does not have the above + instability issue. However, not all features have names + in /proc/cpuinfo. + Note that using this option will taint your kernel. Also note that user programs calling CPUID directly or using the feature without checking anything will still see it. This just prevents it from @@ -831,7 +836,7 @@ Documentation/admin-guide/kdump/kdump.rst for an example. crashkernel=size[KMG],high - [KNL, X86-64] range could be above 4G. Allow kernel + [KNL, X86-64, ARM64] range could be above 4G. Allow kernel to allocate physical memory region from top, so could be above 4G if system have more than 4G ram installed. Otherwise memory region will be allocated below 4G, if @@ -844,14 +849,20 @@ that require some amount of low memory, e.g. swiotlb requires at least 64M+32K low memory, also enough extra low memory is needed to make sure DMA buffers for 32-bit - devices won't run out. Kernel would try to allocate at + devices won't run out. Kernel would try to allocate at least 256M below 4G automatically. - This one let user to specify own low range under 4G + This one lets the user specify own low range under 4G for second kernel instead. 0: to disable low allocation. It will be ignored when crashkernel=X,high is not used or memory reserved is below 4G. + [KNL, ARM64] range in low memory. + This one lets the user specify a low range in the + DMA zone for the crash dump kernel. + It will be ignored when crashkernel=X,high is not used + or memory reserved is located in the DMA zones. + cryptomgr.notests [KNL] Disable crypto self-tests @@ -1917,7 +1928,8 @@ ima_template= [IMA] Select one of defined IMA measurements template formats. - Formats: { "ima" | "ima-ng" | "ima-sig" } + Formats: { "ima" | "ima-ng" | "ima-ngv2" | "ima-sig" | + "ima-sigv2" } Default: "ima-ng" ima_template_fmt= @@ -2636,14 +2648,14 @@ when set. Format: <int> - libata.force= [LIBATA] Force configurations. The format is comma- - separated list of "[ID:]VAL" where ID is - PORT[.DEVICE]. PORT and DEVICE are decimal numbers - matching port, link or device. Basically, it matches - the ATA ID string printed on console by libata. If - the whole ID part is omitted, the last PORT and DEVICE - values are used. If ID hasn't been specified yet, the - configuration applies to all ports, links and devices. + libata.force= [LIBATA] Force configurations. The format is a comma- + separated list of "[ID:]VAL" where ID is PORT[.DEVICE]. + PORT and DEVICE are decimal numbers matching port, link + or device. Basically, it matches the ATA ID string + printed on console by libata. If the whole ID part is + omitted, the last PORT and DEVICE values are used. If + ID hasn't been specified yet, the configuration applies + to all ports, links and devices. If only DEVICE is omitted, the parameter applies to the port and all links and devices behind it. DEVICE @@ -2653,7 +2665,7 @@ host link and device attached to it. The VAL specifies the configuration to force. As long - as there's no ambiguity shortcut notation is allowed. + as there is no ambiguity, shortcut notation is allowed. For example, both 1.5 and 1.5G would work for 1.5Gbps. The following configurations can be forced. @@ -2666,19 +2678,58 @@ udma[/][16,25,33,44,66,100,133] notation is also allowed. + * nohrst, nosrst, norst: suppress hard, soft and both + resets. + + * rstonce: only attempt one reset during hot-unplug + link recovery. + + * [no]dbdelay: Enable or disable the extra 200ms delay + before debouncing a link PHY and device presence + detection. + * [no]ncq: Turn on or off NCQ. - * [no]ncqtrim: Turn off queued DSM TRIM. + * [no]ncqtrim: Enable or disable queued DSM TRIM. + + * [no]ncqati: Enable or disable NCQ trim on ATI chipset. + + * [no]trim: Enable or disable (unqueued) TRIM. + + * trim_zero: Indicate that TRIM command zeroes data. + + * max_trim_128m: Set 128M maximum trim size limit. + + * [no]dma: Turn on or off DMA transfers. + + * atapi_dmadir: Enable ATAPI DMADIR bridge support. + + * atapi_mod16_dma: Enable the use of ATAPI DMA for + commands that are not a multiple of 16 bytes. + + * [no]dmalog: Enable or disable the use of the + READ LOG DMA EXT command to access logs. + + * [no]iddevlog: Enable or disable access to the + identify device data log. - * nohrst, nosrst, norst: suppress hard, soft - and both resets. + * [no]logdir: Enable or disable access to the general + purpose log directory. - * rstonce: only attempt one reset during - hot-unplug link recovery + * max_sec_128: Set transfer size limit to 128 sectors. - * dump_id: dump IDENTIFY data. + * max_sec_1024: Set or clear transfer size limit to + 1024 sectors. - * atapi_dmadir: Enable ATAPI DMADIR bridge support + * max_sec_lba48: Set or clear transfer size limit to + 65535 sectors. + + * [no]lpm: Enable or disable link power management. + + * [no]setxfer: Indicate if transfer speed mode setting + should be skipped. + + * dump_id: Dump IDENTIFY data. * disable: Disable this device. @@ -3117,6 +3168,7 @@ mds=off [X86] tsx_async_abort=off [X86] kvm.nx_huge_pages=off [X86] + srbds=off [X86,INTEL] no_entry_flush [PPC] no_uaccess_flush [PPC] @@ -3443,8 +3495,6 @@ nocache [ARM] - noclflush [BUGS=X86] Don't use the CLFLUSH instruction - nodsp [SH] Disable hardware DSP at boot time. noefi Disable EFI runtime services support. @@ -3453,16 +3503,11 @@ noexec [IA-64] - noexec [X86] - On X86-32 available only on PAE configured kernels. - noexec=on: enable non-executable mappings (default) - noexec=off: disable non-executable mappings - - nosmap [X86,PPC] + nosmap [PPC] Disable SMAP (Supervisor Mode Access Prevention) even if it is supported by processor. - nosmep [X86,PPC64s] + nosmep [PPC64s] Disable SMEP (Supervisor Mode Execution Prevention) even if it is supported by processor. @@ -3662,8 +3707,6 @@ nosbagart [IA-64] - nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support. - nosgx [X86-64,SGX] Disables Intel SGX kernel support. nosmp [SMP] Tells an SMP kernel to act as a UP kernel, @@ -4883,6 +4926,18 @@ rcupdate.rcu_cpu_stall_timeout= [KNL] Set timeout for RCU CPU stall warning messages. + The value is in seconds and the maximum allowed + value is 300 seconds. + + rcupdate.rcu_exp_cpu_stall_timeout= [KNL] + Set timeout for expedited RCU CPU stall warning + messages. The value is in milliseconds + and the maximum allowed value is 21000 + milliseconds. Please note that this value is + adjusted to an arch timer tick resolution. + Setting this to zero causes the value from + rcupdate.rcu_cpu_stall_timeout to be used (after + conversion from seconds to milliseconds). rcupdate.rcu_expedited= [KNL] Use expedited grace-period primitives, for @@ -4945,10 +5000,34 @@ number avoids disturbing real-time workloads, but lengthens grace periods. + rcupdate.rcu_task_stall_info= [KNL] + Set initial timeout in jiffies for RCU task stall + informational messages, which give some indication + of the problem for those not patient enough to + wait for ten minutes. Informational messages are + only printed prior to the stall-warning message + for a given grace period. Disable with a value + less than or equal to zero. Defaults to ten + seconds. A change in value does not take effect + until the beginning of the next grace period. + + rcupdate.rcu_task_stall_info_mult= [KNL] + Multiplier for time interval between successive + RCU task stall informational messages for a given + RCU tasks grace period. This value is clamped + to one through ten, inclusive. It defaults to + the value three, so that the first informational + message is printed 10 seconds into the grace + period, the second at 40 seconds, the third at + 160 seconds, and then the stall warning at 600 + seconds would prevent a fourth at 640 seconds. + rcupdate.rcu_task_stall_timeout= [KNL] - Set timeout in jiffies for RCU task stall warning - messages. Disable with a value less than or equal - to zero. + Set timeout in jiffies for RCU task stall + warning messages. Disable with a value less + than or equal to zero. Defaults to ten minutes. + A change in value does not take effect until + the beginning of the next grace period. rcupdate.rcu_self_test= [KNL] Run the RCU early boot self tests @@ -5289,6 +5368,8 @@ serialnumber [BUGS=X86-32] + sev=option[,option...] [X86-64] See Documentation/x86/x86_64/boot-options.rst + shapers= [NET] Maximal number of shapers. @@ -5358,6 +5439,17 @@ smart2= [HW] Format: <io1>[,<io2>[,...,<io8>]] + smp.csd_lock_timeout= [KNL] + Specify the period of time in milliseconds + that smp_call_function() and friends will wait + for a CPU to release the CSD lock. This is + useful when diagnosing bugs involving CPUs + disabling interrupts for extended periods + of time. Defaults to 5,000 milliseconds, and + setting a value of zero disables this feature. + This feature may be more efficiently disabled + using the csdlock_debug- kernel parameter. + smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port smsc-ircc2.ircc_sir= [HW] SIR base I/O port @@ -5589,6 +5681,30 @@ off: Disable mitigation and remove performance impact to RDRAND and RDSEED + srcutree.big_cpu_lim [KNL] + Specifies the number of CPUs constituting a + large system, such that srcu_struct structures + should immediately allocate an srcu_node array. + This kernel-boot parameter defaults to 128, + but takes effect only when the low-order four + bits of srcutree.convert_to_big is equal to 3 + (decide at boot). + + srcutree.convert_to_big [KNL] + Specifies under what conditions an SRCU tree + srcu_struct structure will be converted to big + form, that is, with an rcu_node tree: + + 0: Never. + 1: At init_srcu_struct() time. + 2: When rcutorture decides to. + 3: Decide at boot time (default). + 0x1X: Above plus if high contention. + + Either way, the srcu_node tree will be sized based + on the actual runtime number of CPUs (nr_cpu_ids) + instead of the compile-time CONFIG_NR_CPUS. + srcutree.counter_wrap_check [KNL] Specifies how frequently to check for grace-period sequence counter wrap for the @@ -5606,6 +5722,14 @@ expediting. Set to zero to disable automatic expediting. + srcutree.small_contention_lim [KNL] + Specifies the number of update-side contention + events per jiffy will be tolerated before + initiating a conversion of an srcu_struct + structure to big form. Note that the value of + srcutree.convert_to_big must have the 0x10 bit + set for contention-based conversions to occur. + ssbd= [ARM64,HW] Speculative Store Bypass Disable control @@ -5963,11 +6087,22 @@ sources: - "tpm" - "tee" + - "caam" If not specified then it defaults to iterating through the trust source list starting with TPM and assigns the first trust source as a backend which is initialized successfully during iteration. + trusted.rng= [KEYS] + Format: <string> + The RNG used to generate key material for trusted keys. + Can be one of: + - "kernel" + - the same value as trusted.source: "tpm" or "tee" + - "default" + If not specified, "default" is used. In this case, + the RNG's choice is left to each individual trust source. + tsc= Disable clocksource stability checks for TSC. Format: <string> [x86] reliable: mark tsc clocksource as reliable, this diff --git a/Documentation/admin-guide/media/vimc.dot b/Documentation/admin-guide/media/vimc.dot index 57863a13fa39..8e829c164626 100644 --- a/Documentation/admin-guide/media/vimc.dot +++ b/Documentation/admin-guide/media/vimc.dot @@ -9,14 +9,14 @@ digraph board { n00000003:port0 -> n00000008:port0 [style=bold] n00000003:port0 -> n0000000f [style=bold] n00000005 [label="{{<port0> 0} | Debayer A\n/dev/v4l-subdev2 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green] - n00000005:port1 -> n00000017:port0 + n00000005:port1 -> n00000015:port0 n00000008 [label="{{<port0> 0} | Debayer B\n/dev/v4l-subdev3 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green] - n00000008:port1 -> n00000017:port0 [style=dashed] + n00000008:port1 -> n00000015:port0 [style=dashed] n0000000b [label="Raw Capture 0\n/dev/video0", shape=box, style=filled, fillcolor=yellow] n0000000f [label="Raw Capture 1\n/dev/video1", shape=box, style=filled, fillcolor=yellow] - n00000013 [label="RGB/YUV Input\n/dev/video2", shape=box, style=filled, fillcolor=yellow] - n00000013 -> n00000017:port0 [style=dashed] - n00000017 [label="{{<port0> 0} | Scaler\n/dev/v4l-subdev4 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green] - n00000017:port1 -> n0000001a [style=bold] - n0000001a [label="RGB/YUV Capture\n/dev/video3", shape=box, style=filled, fillcolor=yellow] + n00000013 [label="{{} | RGB/YUV Input\n/dev/v4l-subdev4 | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] + n00000013:port0 -> n00000015:port0 [style=dashed] + n00000015 [label="{{<port0> 0} | Scaler\n/dev/v4l-subdev5 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green] + n00000015:port1 -> n00000018 [style=bold] + n00000018 [label="RGB/YUV Capture\n/dev/video2", shape=box, style=filled, fillcolor=yellow] } diff --git a/Documentation/admin-guide/sysctl/kernel.rst b/Documentation/admin-guide/sysctl/kernel.rst index 545d2d7420a1..ddccd1077462 100644 --- a/Documentation/admin-guide/sysctl/kernel.rst +++ b/Documentation/admin-guide/sysctl/kernel.rst @@ -1001,6 +1001,9 @@ This is a directory, with the following entries: * ``boot_id``: a UUID generated the first time this is retrieved, and unvarying after that; +* ``uuid``: a UUID generated every time this is retrieved (this can + thus be used to generate UUIDs at will); + * ``entropy_avail``: the pool's entropy count, in bits; * ``poolsize``: the entropy pool size, in bits; @@ -1008,10 +1011,7 @@ This is a directory, with the following entries: * ``urandom_min_reseed_secs``: obsolete (used to determine the minimum number of seconds between urandom pool reseeding). This file is writable for compatibility purposes, but writing to it has no effect - on any RNG behavior. - -* ``uuid``: a UUID generated every time this is retrieved (this can - thus be used to generate UUIDs at will); + on any RNG behavior; * ``write_wakeup_threshold``: when the entropy count drops below this (as a number of bits), processes waiting to write to ``/dev/random`` |