1 files changed, 0 insertions, 177 deletions
diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
deleted file mode 100644
index 26410fbb85be..000000000000
--- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
+++ /dev/null
@@ -1,177 +0,0 @@
-Marvell Armada AP806 System Controller
-======================================
-
-The AP806 is one of the two core HW blocks of the Marvell Armada 7K/8K
-SoCs. It contains system controllers, which provide several registers
-giving access to numerous features: clocks, pin-muxing and many other
-SoC configuration items. This DT binding allows to describe these
-system controllers.
-
-For the top level node:
- - compatible: must be: "syscon", "simple-mfd";
- - reg: register area of the AP806 system controller
-
-SYSTEM CONTROLLER 0
-===================
-
-Clocks:
--------
-
-
-The Device Tree node representing the AP806/AP807 system controller
-provides a number of clocks:
-
- - 0: reference clock of CPU cluster 0
- - 1: reference clock of CPU cluster 1
- - 2: fixed PLL at 1200 Mhz
- - 3: MSS clock, derived from the fixed PLL
-
-Required properties:
-
- - compatible: must be one of:
-   * "marvell,ap806-clock"
-   * "marvell,ap807-clock"
- - #clock-cells: must be set to 1
-
-Pinctrl:
---------
-
-For common binding part and usage, refer to
-Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt.
-
-Required properties:
-- compatible must be "marvell,ap806-pinctrl",
-
-Available mpp pins/groups and functions:
-Note: brackets (x) are not part of the mpp name for marvell,function and given
-only for more detailed description in this document.
-
-name	pins	functions
-================================================================================
-mpp0	0	gpio, sdio(clk), spi0(clk)
-mpp1	1	gpio, sdio(cmd), spi0(miso)
-mpp2	2	gpio, sdio(d0), spi0(mosi)
-mpp3	3	gpio, sdio(d1), spi0(cs0n)
-mpp4	4	gpio, sdio(d2), i2c0(sda)
-mpp5	5	gpio, sdio(d3), i2c0(sdk)
-mpp6	6	gpio, sdio(ds)
-mpp7	7	gpio, sdio(d4), uart1(rxd)
-mpp8	8	gpio, sdio(d5), uart1(txd)
-mpp9	9	gpio, sdio(d6), spi0(cs1n)
-mpp10	10	gpio, sdio(d7)
-mpp11	11	gpio, uart0(txd)
-mpp12	12	gpio, sdio(pw_off), sdio(hw_rst)
-mpp13	13	gpio
-mpp14	14	gpio
-mpp15	15	gpio
-mpp16	16	gpio
-mpp17	17	gpio
-mpp18	18	gpio
-mpp19	19	gpio, uart0(rxd), sdio(pw_off)
-
-GPIO:
------
-For common binding part and usage, refer to
-Documentation/devicetree/bindings/gpio/gpio-mvebu.txt.
-
-Required properties:
-
-- compatible: "marvell,armada-8k-gpio"
-
-- offset: offset address inside the syscon block
-
-Example:
-ap_syscon: system-controller@6f4000 {
-	compatible = "syscon", "simple-mfd";
-	reg = <0x6f4000 0x1000>;
-
-	ap_clk: clock {
-		compatible = "marvell,ap806-clock";
-		#clock-cells = <1>;
-	};
-
-	ap_pinctrl: pinctrl {
-		compatible = "marvell,ap806-pinctrl";
-	};
-
-	ap_gpio: gpio {
-		compatible = "marvell,armada-8k-gpio";
-		offset = <0x1040>;
-		ngpios = <19>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&ap_pinctrl 0 0 19>;
-	};
-};
-
-SYSTEM CONTROLLER 1
-===================
-
-Thermal:
---------
-
-For common binding part and usage, refer to
-Documentation/devicetree/bindings/thermal/thermal.txt
-
-The thermal IP can probe the temperature all around the processor. It
-may feature several channels, each of them wired to one sensor.
-
-It is possible to setup an overheat interrupt by giving at least one
-critical point to any subnode of the thermal-zone node.
-
-Required properties:
-- compatible: must be one of:
-  * marvell,armada-ap806-thermal
-- reg: register range associated with the thermal functions.
-
-Optional properties:
-- interrupts: overheat interrupt handle. Should point to line 18 of the
-  SEI irqchip. See interrupt-controller/interrupts.txt
-- #thermal-sensor-cells: shall be <1> when thermal-zones subnodes refer
-  to this IP and represents the channel ID. There is one sensor per
-  channel. O refers to the thermal IP internal channel, while positive
-  IDs refer to each CPU.
-
-Example:
-ap_syscon1: system-controller@6f8000 {
-	compatible = "syscon", "simple-mfd";
-	reg = <0x6f8000 0x1000>;
-
-	ap_thermal: thermal-sensor@80 {
-		compatible = "marvell,armada-ap806-thermal";
-		reg = <0x80 0x10>;
-		interrupt-parent = <&sei>;
-		interrupts = <18>;
-		#thermal-sensor-cells = <1>;
-	};
-};
-
-Cluster clocks:
----------------
-
-Device Tree Clock bindings for cluster clock of Marvell
-AP806/AP807. Each cluster contain up to 2 CPUs running at the same
-frequency.
-
-Required properties:
- - compatible: must be one of:
-   * "marvell,ap806-cpu-clock"
-   * "marvell,ap807-cpu-clock"
-- #clock-cells : should be set to 1.
-
-- clocks : shall be the input parent clock(s) phandle for the clock
-           (one per cluster)
-
-- reg: register range associated with the cluster clocks
-
-ap_syscon1: system-controller@6f8000 {
-	compatible = "marvell,armada-ap806-syscon1", "syscon", "simple-mfd";
-	reg = <0x6f8000 0x1000>;
-
-	cpu_clk: clock-cpu@278 {
-		compatible = "marvell,ap806-cpu-clock";
-		clocks = <&ap_clk 0>, <&ap_clk 1>;
-		#clock-cells = <1>;
-		reg = <0x278 0xa30>;
-	};
-};