diff options
Diffstat (limited to '')
15 files changed, 947 insertions, 248 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-ceva.txt b/Documentation/devicetree/bindings/ata/ahci-ceva.txt deleted file mode 100644 index bfb6da0281ec..000000000000 --- a/Documentation/devicetree/bindings/ata/ahci-ceva.txt +++ /dev/null @@ -1,63 +0,0 @@ -Binding for CEVA AHCI SATA Controller - -Required properties: - - reg: Physical base address and size of the controller's register area. - - compatible: Compatibility string. Must be 'ceva,ahci-1v84'. - - clocks: Input clock specifier. Refer to common clock bindings. - - interrupts: Interrupt specifier. Refer to interrupt binding. - - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for port 0. - - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; - CINMP : COMINIT Negate Minimum Period. - CIBGN : COMINIT Burst Gap Nominal. - CIBGMX: COMINIT Burst Gap Maximum. - CIBGMN: COMINIT Burst Gap Minimum. - - ceva,p0-comwake-params: OOB timing value for COMWAKE parameter for port 0. - - ceva,p1-comwake-params: OOB timing value for COMWAKE parameter for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; - CWBGMN: COMWAKE Burst Gap Minimum. - CWBGMX: COMWAKE Burst Gap Maximum. - CWBGN: COMWAKE Burst Gap Nominal. - CWNMP: COMWAKE Negate Minimum Period. - - ceva,p0-burst-params: Burst timing value for COM parameter for port 0. - - ceva,p1-burst-params: Burst timing value for COM parameter for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-burst-params = /bits/ 8 <BMX BNM SFD PTST>; - BMX: COM Burst Maximum. - BNM: COM Burst Nominal. - SFD: Signal Failure Detection value. - PTST: Partial to Slumber timer value. - - ceva,p0-retry-params: Retry interval timing value for port 0. - - ceva,p1-retry-params: Retry interval timing value for port 1. - The fields for the above parameter must be as shown below: - ceva,pN-retry-params = /bits/ 16 <RIT RCT>; - RIT: Retry Interval Timer. - RCT: Rate Change Timer. - -Optional properties: - - ceva,broken-gen2: limit to gen1 speed instead of gen2. - - phys: phandle for the PHY device - - resets: phandle to the reset controller for the SATA IP - -Examples: - ahci@fd0c0000 { - compatible = "ceva,ahci-1v84"; - reg = <0xfd0c0000 0x200>; - interrupt-parent = <&gic>; - interrupts = <0 133 4>; - clocks = <&clkc SATA_CLK_ID>; - ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; - ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; - ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; - ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>; - - ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; - ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; - ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; - ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>; - ceva,broken-gen2; - phys = <&psgtr 1 PHY_TYPE_SATA 1 1>; - resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; - }; diff --git a/Documentation/devicetree/bindings/ata/ahci-common.yaml b/Documentation/devicetree/bindings/ata/ahci-common.yaml new file mode 100644 index 000000000000..94d72aeaad0f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-common.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ahci-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Serial ATA AHCI controllers + +maintainers: + - Hans de Goede <hdegoede@redhat.com> + - Damien Le Moal <damien.lemoal@opensource.wdc.com> + +description: + This document defines device tree properties for a common AHCI SATA + controller implementation. It's hardware interface is supposed to + conform to the technical standard defined by Intel (see Serial ATA + Advanced Host Controller Interface specification for details). The + document doesn't constitute a DT-node binding by itself but merely + defines a set of common properties for the AHCI-compatible devices. + +select: false + +allOf: + - $ref: sata-common.yaml# + +properties: + reg: + description: + Generic AHCI registers space conforming to the Serial ATA AHCI + specification. + + reg-names: + description: CSR space IDs + contains: + const: ahci + + interrupts: + description: + Generic AHCI state change interrupt. Can be implemented either as a + single line attached to the controller or as a set of the signals + indicating the particular port events. + minItems: 1 + maxItems: 32 + + ahci-supply: + description: Power regulator for AHCI controller + + target-supply: + description: Power regulator for SATA target device + + phy-supply: + description: Power regulator for SATA PHY + + phys: + description: Reference to the SATA PHY node + maxItems: 1 + + phy-names: + const: sata-phy + + hba-cap: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Bitfield of the HBA generic platform capabilities like Staggered + Spin-up or Mechanical Presence Switch support. It can be used to + appropriately initialize the HWinit fields of the HBA CAP register + in case if the system firmware hasn't done it. + + ports-implemented: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Mask that indicates which ports the HBA supports. Useful if PI is not + programmed by the BIOS, which is true for some embedded SoC's. + +patternProperties: + "^sata-port@[0-9a-f]+$": + $ref: '#/$defs/ahci-port' + description: + It is optionally possible to describe the ports as sub-nodes so + to enable each port independently when dealing with multiple PHYs. + +required: + - reg + - interrupts + +additionalProperties: true + +$defs: + ahci-port: + $ref: /schemas/ata/sata-common.yaml#/$defs/sata-port + + properties: + reg: + description: + AHCI SATA port identifier. By design AHCI controller can't have + more than 32 ports due to the CAP.NP fields and PI register size + constraints. + minimum: 0 + maximum: 31 + + phys: + description: Individual AHCI SATA port PHY + maxItems: 1 + + phy-names: + description: AHCI SATA port PHY ID + const: sata-phy + + target-supply: + description: Power regulator for SATA port target device + + hba-port-cap: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Bitfield of the HBA port-specific platform capabilities like Hot + plugging, eSATA, FIS-based Switching, etc (see AHCI specification + for details). It can be used to initialize the HWinit fields of + the PxCMD register in case if the system firmware hasn't done it. + + required: + - reg + +... diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt deleted file mode 100644 index 77091a277642..000000000000 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ /dev/null @@ -1,79 +0,0 @@ -* AHCI SATA Controller - -SATA nodes are defined to describe on-chip Serial ATA controllers. -Each SATA controller should have its own node. - -It is possible, but not required, to represent each port as a sub-node. -It allows to enable each port independently when dealing with multiple -PHYs. - -Required properties: -- compatible : compatible string, one of: - - "brcm,iproc-ahci" - - "hisilicon,hisi-ahci" - - "cavium,octeon-7130-ahci" - - "ibm,476gtr-ahci" - - "marvell,armada-380-ahci" - - "marvell,armada-3700-ahci" - - "snps,dwc-ahci" - - "snps,spear-ahci" - - "generic-ahci" -- interrupts : <interrupt mapping for SATA IRQ> -- reg : <registers mapping> - -Please note that when using "generic-ahci" you must also specify a SoC specific -compatible: - compatible = "manufacturer,soc-model-ahci", "generic-ahci"; - -Optional properties: -- dma-coherent : Present if dma operations are coherent -- clocks : a list of phandle + clock specifier pairs -- resets : a list of phandle + reset specifier pairs -- target-supply : regulator for SATA target power -- phy-supply : regulator for PHY power -- phys : reference to the SATA PHY node -- phy-names : must be "sata-phy" -- ahci-supply : regulator for AHCI controller -- ports-implemented : Mask that indicates which ports that the HBA supports - are available for software to use. Useful if PORTS_IMPL - is not programmed by the BIOS, which is true with - some embedded SOC's. - -Required properties when using sub-nodes: -- #address-cells : number of cells to encode an address -- #size-cells : number of cells representing the size of an address - -Sub-nodes required properties: -- reg : the port number -And at least one of the following properties: -- phys : reference to the SATA PHY node -- target-supply : regulator for SATA target power - -Examples: - sata@ffe08000 { - compatible = "snps,spear-ahci"; - reg = <0xffe08000 0x1000>; - interrupts = <115>; - }; - -With sub-nodes: - sata@f7e90000 { - compatible = "marvell,berlin2q-achi", "generic-ahci"; - reg = <0xe90000 0x1000>; - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&chip CLKID_SATA>; - #address-cells = <1>; - #size-cells = <0>; - - sata0: sata-port@0 { - reg = <0>; - phys = <&sata_phy 0>; - target-supply = <®_sata0>; - }; - - sata1: sata-port@1 { - reg = <1>; - phys = <&sata_phy 1>; - target-supply = <®_sata1>;; - }; - }; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.yaml b/Documentation/devicetree/bindings/ata/ahci-platform.yaml new file mode 100644 index 000000000000..7dc2a2e8f598 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-platform.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ahci-platform.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AHCI SATA Controller + +description: | + SATA nodes are defined to describe on-chip Serial ATA controllers. + Each SATA controller should have its own node. + + It is possible, but not required, to represent each port as a sub-node. + It allows to enable each port independently when dealing with multiple + PHYs. + +maintainers: + - Hans de Goede <hdegoede@redhat.com> + - Jens Axboe <axboe@kernel.dk> + +select: + properties: + compatible: + contains: + enum: + - brcm,iproc-ahci + - cavium,octeon-7130-ahci + - hisilicon,hisi-ahci + - ibm,476gtr-ahci + - marvell,armada-3700-ahci + - marvell,armada-8k-ahci + - marvell,berlin2q-ahci + required: + - compatible + +allOf: + - $ref: "ahci-common.yaml#" + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,iproc-ahci + - marvell,armada-8k-ahci + - marvell,berlin2-ahci + - marvell,berlin2q-ahci + - const: generic-ahci + - enum: + - cavium,octeon-7130-ahci + - hisilicon,hisi-ahci + - ibm,476gtr-ahci + - marvell,armada-3700-ahci + + reg: + minItems: 1 + maxItems: 2 + + reg-names: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +patternProperties: + "^sata-port@[0-9a-f]+$": + $ref: /schemas/ata/ahci-common.yaml#/$defs/ahci-port + + anyOf: + - required: [ phys ] + - required: [ target-supply ] + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + sata@ffe08000 { + compatible = "snps,spear-ahci"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + }; + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/berlin2q.h> + #include <dt-bindings/ata/ahci.h> + + sata@f7e90000 { + compatible = "marvell,berlin2q-ahci", "generic-ahci"; + reg = <0xf7e90000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + + hba-cap = <HBA_SMPS>; + + sata0: sata-port@0 { + reg = <0>; + + phys = <&sata_phy 0>; + target-supply = <®_sata0>; + + hba-port-cap = <(HBA_PORT_FBSCP | HBA_PORT_ESP)>; + }; + + sata1: sata-port@1 { + reg = <1>; + + phys = <&sata_phy 1>; + target-supply = <®_sata1>; + + hba-port-cap = <(HBA_PORT_HPCP | HBA_PORT_MPSP | HBA_PORT_FBSCP)>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/baikal,bt1-ahci.yaml b/Documentation/devicetree/bindings/ata/baikal,bt1-ahci.yaml new file mode 100644 index 000000000000..9b7ca4759bd7 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/baikal,bt1-ahci.yaml @@ -0,0 +1,115 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/baikal,bt1-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 SoC AHCI SATA controller + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + AHCI SATA controller embedded into the Baikal-T1 SoC is based on the + DWC AHCI SATA v4.10a IP-core. + +allOf: + - $ref: snps,dwc-ahci-common.yaml# + +properties: + compatible: + const: baikal,bt1-ahci + + clocks: + items: + - description: Peripheral APB bus clock + - description: Application AXI BIU clock + - description: SATA Ports reference clock + + clock-names: + items: + - const: pclk + - const: aclk + - const: ref + + resets: + items: + - description: Application AXI BIU domain reset + - description: SATA Ports clock domain reset + + reset-names: + items: + - const: arst + - const: ref + + ports-implemented: + maximum: 0x3 + +patternProperties: + "^sata-port@[0-1]$": + $ref: /schemas/ata/snps,dwc-ahci-common.yaml#/$defs/dwc-ahci-port + + properties: + reg: + minimum: 0 + maximum: 1 + + snps,tx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Due to having AXI3 bus interface utilized the maximum Tx DMA + transaction size can't exceed 16 beats (AxLEN[3:0]). + enum: [ 1, 2, 4, 8, 16 ] + + snps,rx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Due to having AXI3 bus interface utilized the maximum Rx DMA + transaction size can't exceed 16 beats (AxLEN[3:0]). + enum: [ 1, 2, 4, 8, 16 ] + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +unevaluatedProperties: false + +examples: + - | + sata@1f050000 { + compatible = "baikal,bt1-ahci"; + reg = <0x1f050000 0x2000>; + #address-cells = <1>; + #size-cells = <0>; + + interrupts = <0 64 4>; + + clocks = <&ccu_sys 1>, <&ccu_axi 2>, <&sata_ref_clk>; + clock-names = "pclk", "aclk", "ref"; + + resets = <&ccu_axi 2>, <&ccu_sys 0>; + reset-names = "arst", "ref"; + + ports-implemented = <0x3>; + + sata-port@0 { + reg = <0>; + + snps,tx-ts-max = <4>; + snps,rx-ts-max = <4>; + }; + + sata-port@1 { + reg = <1>; + + snps,tx-ts-max = <4>; + snps,rx-ts-max = <4>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt deleted file mode 100644 index b9ae4ce4a0a0..000000000000 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt +++ /dev/null @@ -1,45 +0,0 @@ -* Broadcom SATA3 AHCI Controller - -SATA nodes are defined to describe on-chip Serial ATA controllers. -Each SATA controller should have its own node. - -Required properties: -- compatible : should be one or more of - "brcm,bcm7216-ahci" - "brcm,bcm7425-ahci" - "brcm,bcm7445-ahci" - "brcm,bcm-nsp-ahci" - "brcm,sata3-ahci" - "brcm,bcm63138-ahci" -- reg : register mappings for AHCI and SATA_TOP_CTRL -- reg-names : "ahci" and "top-ctrl" -- interrupts : interrupt mapping for SATA IRQ - -Optional properties: - -- reset: for "brcm,bcm7216-ahci" must be a valid reset phandle - pointing to the RESCAL reset controller provider node. -- reset-names: for "brcm,bcm7216-ahci", must be "rescal". - -Also see ahci-platform.txt. - -Example: - - sata@f045a000 { - compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci"; - reg = <0xf045a000 0xa9c>, <0xf0458040 0x24>; - reg-names = "ahci", "top-ctrl"; - interrupts = <0 30 0>; - #address-cells = <1>; - #size-cells = <0>; - - sata0: sata-port@0 { - reg = <0>; - phys = <&sata_phy 0>; - }; - - sata1: sata-port@1 { - reg = <1>; - phys = <&sata_phy 1>; - }; - }; diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.yaml b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.yaml new file mode 100644 index 000000000000..fe7f091e744f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/brcm,sata-brcm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom SATA3 AHCI Controller + +description: + SATA nodes are defined to describe on-chip Serial ATA controllers. + Each SATA controller should have its own node. + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +allOf: + - $ref: ahci-common.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,bcm7216-ahci + - brcm,bcm7445-ahci + - brcm,bcm7425-ahci + - brcm,bcm63138-ahci + - const: brcm,sata3-ahci + - items: + - const: brcm,bcm-nsp-ahci + + reg: + maxItems: 2 + + reg-names: + items: + - const: ahci + - const: top-ctrl + + interrupts: + maxItems: 1 + +if: + properties: + compatible: + contains: + enum: + - brcm,bcm7216-ahci + - brcm,bcm63138-ahci +then: + properties: + resets: + maxItems: 1 + reset-names: + enum: + - rescal + - ahci + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + +unevaluatedProperties: false + +examples: + - | + sata@f045a000 { + compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci"; + reg = <0xf045a000 0xa9c>, <0xf0458040 0x24>; + reg-names = "ahci", "top-ctrl"; + interrupts = <0 30 0>; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy 0>; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml b/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml new file mode 100644 index 000000000000..9b31f864e071 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml @@ -0,0 +1,189 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ceva,ahci-1v84.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ceva AHCI SATA Controller + +maintainers: + - Piyush Mehta <piyush.mehta@xilinx.com> + +description: | + The Ceva SATA controller mostly conforms to the AHCI interface with some + special extensions to add functionality, is a high-performance dual-port + SATA host controller with an AHCI compliant command layer which supports + advanced features such as native command queuing and frame information + structure (FIS) based switching for systems employing port multipliers. + +properties: + compatible: + const: ceva,ahci-1v84 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + dma-coherent: true + + interrupts: + maxItems: 1 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + + ceva,p0-cominit-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMINIT parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + items: + - description: CINMP - COMINIT Negate Minimum Period. + - description: CIBGN - COMINIT Burst Gap Nominal. + - description: CIBGMX - COMINIT Burst Gap Maximum. + - description: CIBGMN - COMINIT Burst Gap Minimum. + + ceva,p0-comwake-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMWAKE parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + items: + - description: CWBGMN - COMWAKE Burst Gap Minimum. + - description: CWBGMX - COMWAKE Burst Gap Maximum. + - description: CWBGN - COMWAKE Burst Gap Nominal. + - description: CWNMP - COMWAKE Negate Minimum Period. + + ceva,p0-burst-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + Burst timing value for COM parameter for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + items: + - description: BMX - COM Burst Maximum. + - description: BNM - COM Burst Nominal. + - description: SFD - Signal Failure Detection value. + - description: PTST - Partial to Slumber timer value. + + ceva,p0-retry-params: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: | + Retry interval timing value for port 0. + The fields for the above parameter must be as shown below:- + ceva,p0-retry-params = /bits/ 16 <RIT RCT>; + items: + - description: RIT - Retry Interval Timer. + - description: RCT - Rate Change Timer. + + ceva,p1-cominit-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMINIT parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + items: + - description: CINMP - COMINIT Negate Minimum Period. + - description: CIBGN - COMINIT Burst Gap Nominal. + - description: CIBGMX - COMINIT Burst Gap Maximum. + - description: CIBGMN - COMINIT Burst Gap Minimum. + + ceva,p1-comwake-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + OOB timing value for COMWAKE parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + items: + - description: CWBGMN - COMWAKE Burst Gap Minimum. + - description: CWBGMX - COMWAKE Burst Gap Maximum. + - description: CWBGN - COMWAKE Burst Gap Nominal. + - description: CWNMP - COMWAKE Negate Minimum Period. + + ceva,p1-burst-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: | + Burst timing value for COM parameter for port 1. + The fields for the above parameter must be as shown below:- + ceva,p1-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + items: + - description: BMX - COM Burst Maximum. + - description: BNM - COM Burst Nominal. + - description: SFD - Signal Failure Detection value. + - description: PTST - Partial to Slumber timer value. + + ceva,p1-retry-params: + $ref: /schemas/types.yaml#/definitions/uint16-array + description: | + Retry interval timing value for port 1. + The fields for the above parameter must be as shown below:- + ceva,pN-retry-params = /bits/ 16 <RIT RCT>; + items: + - description: RIT - Retry Interval Timer. + - description: RCT - Rate Change Timer. + + ceva,broken-gen2: + $ref: /schemas/types.yaml#/definitions/flag + description: | + limit to gen1 speed instead of gen2. + + phys: + maxItems: 1 + + phy-names: + items: + - const: sata-phy + + resets: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - interrupts + - ceva,p0-cominit-params + - ceva,p0-comwake-params + - ceva,p0-burst-params + - ceva,p0-retry-params + - ceva,p1-cominit-params + - ceva,p1-comwake-params + - ceva,p1-burst-params + - ceva,p1-retry-params + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/xlnx-zynqmp-power.h> + #include <dt-bindings/reset/xlnx-zynqmp-resets.h> + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + #include <dt-bindings/phy/phy.h> + + sata: ahci@fd0c0000 { + compatible = "ceva,ahci-1v84"; + reg = <0xfd0c0000 0x200>; + interrupt-parent = <&gic>; + interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zynqmp_clk SATA_REF>; + ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>; + ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>; + ceva,broken-gen2; + phys = <&psgtr 1 PHY_TYPE_SATA 1 1>; + resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; + }; diff --git a/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt deleted file mode 100644 index 1c3d3cc70051..000000000000 --- a/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt +++ /dev/null @@ -1,55 +0,0 @@ -* Cortina Systems Gemini SATA Bridge - -The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that -takes two Faraday Technology FTIDE010 PATA controllers and bridges -them in different configurations to two SATA ports. - -Required properties: -- compatible: should be - "cortina,gemini-sata-bridge" -- reg: registers and size for the block -- resets: phandles to the reset lines for both SATA bridges -- reset-names: must be "sata0", "sata1" -- clocks: phandles to the compulsory peripheral clocks -- clock-names: must be "SATA0_PCLK", "SATA1_PCLK" -- syscon: a phandle to the global Gemini system controller -- cortina,gemini-ata-muxmode: tell the desired multiplexing mode for - the ATA controller and SATA bridges. Values 0..3: - Mode 0: ata0 master <-> sata0 - ata1 master <-> sata1 - ata0 slave interface brought out on IDE pads - Mode 1: ata0 master <-> sata0 - ata1 master <-> sata1 - ata1 slave interface brought out on IDE pads - Mode 2: ata1 master <-> sata1 - ata1 slave <-> sata0 - ata0 master and slave interfaces brought out - on IDE pads - Mode 3: ata0 master <-> sata0 - ata0 slave <-> sata1 - ata1 master and slave interfaces brought out - on IDE pads - -Optional boolean properties: -- cortina,gemini-enable-ide-pins: enables the PATA to IDE connection. - The muxmode setting decides whether ATA0 or ATA1 is brought out, - and whether master, slave or both interfaces get brought out. -- cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge - inside the Gemnini SoC. The Muxmode decides what PATA blocks will - be muxed out and how. - -Example: - -sata: sata@46000000 { - compatible = "cortina,gemini-sata-bridge"; - reg = <0x46000000 0x100>; - resets = <&rcon 26>, <&rcon 27>; - reset-names = "sata0", "sata1"; - clocks = <&gcc GEMINI_CLK_GATE_SATA0>, - <&gcc GEMINI_CLK_GATE_SATA1>; - clock-names = "SATA0_PCLK", "SATA1_PCLK"; - syscon = <&syscon>; - cortina,gemini-ata-muxmode = <3>; - cortina,gemini-enable-ide-pins; - cortina,gemini-enable-sata-bridge; -}; diff --git a/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file mode 100644 index 000000000000..529093666508 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/cortina,gemini-sata-bridge.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cortina Systems Gemini SATA Bridge + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that + takes two Faraday Technology FTIDE010 PATA controllers and bridges + them in different configurations to two SATA ports. + +properties: + compatible: + const: cortina,gemini-sata-bridge + + reg: + maxItems: 1 + + resets: + maxItems: 2 + description: phandles to the reset lines for both SATA bridges + + reset-names: + items: + - const: sata0 + - const: sata1 + + clocks: + maxItems: 2 + description: phandles to the compulsory peripheral clocks + + clock-names: + items: + - const: SATA0_PCLK + - const: SATA1_PCLK + + syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the global Gemini system controller + + cortina,gemini-ata-muxmode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 + - 1 + - 2 + - 3 + description: | + Tell the desired multiplexing mode for the ATA controller and SATA + bridges. + Mode 0: ata0 master <-> sata0 + ata1 master <-> sata1 + ata0 slave interface brought out on IDE pads + Mode 1: ata0 master <-> sata0 + ata1 master <-> sata1 + ata1 slave interface brought out on IDE pads + Mode 2: ata1 master <-> sata1 + ata1 slave <-> sata0 + ata0 master and slave interfaces brought out on IDE pads + Mode 3: ata0 master <-> sata0 + ata0 slave <-> sata1 + ata1 master and slave interfaces brought out on IDE pads + + cortina,gemini-enable-ide-pins: + type: boolean + description: Enables the PATA to IDE connection. + The muxmode setting decides whether ATA0 or ATA1 is brought out, + and whether master, slave or both interfaces get brought out. + + cortina,gemini-enable-sata-bridge: + type: boolean + description: Enables the PATA to SATA bridge inside the Gemnini SoC. + The Muxmode decides what PATA blocks will be muxed out and how. + +required: + - clocks + - clock-names + - cortina,gemini-ata-muxmode + - resets + - reset-names + - compatible + - reg + - syscon + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/cortina,gemini-clock.h> + sata@46000000 { + compatible = "cortina,gemini-sata-bridge"; + reg = <0x46000000 0x100>; + resets = <&rcon 26>, <&rcon 27>; + reset-names = "sata0", "sata1"; + clocks = <&gcc GEMINI_CLK_GATE_SATA0>, + <&gcc GEMINI_CLK_GATE_SATA1>; + clock-names = "SATA0_PCLK", "SATA1_PCLK"; + syscon = <&syscon>; + cortina,gemini-ata-muxmode = <3>; + cortina,gemini-enable-ide-pins; + cortina,gemini-enable-sata-bridge; + }; diff --git a/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml b/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml index c060c7914cae..c4e4a9eab658 100644 --- a/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml +++ b/Documentation/devicetree/bindings/ata/renesas,rcar-sata.yaml @@ -26,6 +26,7 @@ properties: - items: - enum: - renesas,sata-r8a774b1 # RZ/G2N + - renesas,sata-r8a774e1 # RZ/G2H - renesas,sata-r8a7795 # R-Car H3 - renesas,sata-r8a77965 # R-Car M3-N - const: renesas,rcar-gen3-sata # generic R-Car Gen3 or RZ/G2 diff --git a/Documentation/devicetree/bindings/ata/sata-common.yaml b/Documentation/devicetree/bindings/ata/sata-common.yaml index 7ac77b1c5850..58c9342b9925 100644 --- a/Documentation/devicetree/bindings/ata/sata-common.yaml +++ b/Documentation/devicetree/bindings/ata/sata-common.yaml @@ -31,22 +31,27 @@ properties: "#size-cells": const: 0 + dma-coherent: true + patternProperties: "^sata-port@[0-9a-e]$": + $ref: '#/$defs/sata-port' description: | DT nodes for ports connected on the SATA host. The SATA port nodes will be named "sata-port". + +additionalProperties: true + +$defs: + sata-port: type: object properties: reg: minimum: 0 - maximum: 14 description: - The ID number of the drive port SATA can potentially use a port - multiplier making it possible to connect up to 15 disks to a single - SATA port. - -additionalProperties: true + The ID number of the SATA port. Aside with being directly used, + each port can have a Port Multiplier attached thus allowing to + access more than one drive by means of a single SATA port. ... diff --git a/Documentation/devicetree/bindings/ata/sata_highbank.yaml b/Documentation/devicetree/bindings/ata/sata_highbank.yaml index ce75d77e9289..f23f26a8f21c 100644 --- a/Documentation/devicetree/bindings/ata/sata_highbank.yaml +++ b/Documentation/devicetree/bindings/ata/sata_highbank.yaml @@ -51,6 +51,8 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array minItems: 1 maxItems: 8 + items: + maxItems: 2 calxeda,tx-atten: description: | diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml new file mode 100644 index 000000000000..c1457910520b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/snps,dwc-ahci-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DWC AHCI SATA controller properties + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + This document defines device tree schema for the generic Synopsys DWC + AHCI controller properties. + +select: false + +allOf: + - $ref: ahci-common.yaml# + +properties: + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: + Basic DWC AHCI SATA clock sources like application AXI/AHB BIU clock, + PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx) + clock, etc. + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + items: + oneOf: + - description: Application APB/AHB/AXI BIU clock + enum: + - pclk + - aclk + - hclk + - sata + - description: Power Module keep-alive clock + const: pmalive + - description: RxOOB detection clock + const: rxoob + - description: SATA Ports reference clock + const: ref + + resets: + description: + At least basic application and reference clock domains resets are + normally supported by the DWC AHCI SATA controller. + minItems: 1 + maxItems: 4 + + reset-names: + minItems: 1 + maxItems: 4 + items: + oneOf: + - description: Application AHB/AXI BIU clock domain reset control + enum: + - arst + - hrst + - description: Power Module keep-alive clock domain reset control + const: pmalive + - description: RxOOB detection clock domain reset control + const: rxoob + - description: Reference clock domain reset control + const: ref + +patternProperties: + "^sata-port@[0-9a-e]$": + $ref: '#/$defs/dwc-ahci-port' + +additionalProperties: true + +$defs: + dwc-ahci-port: + $ref: /schemas/ata/ahci-common.yaml#/$defs/ahci-port + + properties: + reg: + minimum: 0 + maximum: 7 + + snps,tx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximal size of Tx DMA transactions in FIFO words + enum: [ 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 ] + + snps,rx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximal size of Rx DMA transactions in FIFO words + enum: [ 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 ] + +... diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml new file mode 100644 index 000000000000..5afa4b57ce20 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/snps,dwc-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DWC AHCI SATA controller + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + This document defines device tree bindings for the generic Synopsys DWC + implementation of the AHCI SATA controller. + +allOf: + - $ref: snps,dwc-ahci-common.yaml# + +properties: + compatible: + oneOf: + - description: Synopsys AHCI SATA-compatible devices + const: snps,dwc-ahci + - description: SPEAr1340 AHCI SATA device + const: snps,spear-ahci + - description: Rockhip RK3568 AHCI controller + items: + - const: rockchip,rk3568-dwc-ahci + - const: snps,dwc-ahci + +patternProperties: + "^sata-port@[0-9a-e]$": + $ref: /schemas/ata/snps,dwc-ahci-common.yaml#/$defs/dwc-ahci-port + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/ata/ahci.h> + + sata@122f0000 { + compatible = "snps,dwc-ahci"; + reg = <0x122F0000 0x1ff>; + #address-cells = <1>; + #size-cells = <0>; + + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clock1>, <&clock2>; + clock-names = "aclk", "ref"; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + + ports-implemented = <0x1>; + + sata-port@0 { + reg = <0>; + + hba-port-cap = <HBA_PORT_FBSCP>; + + snps,tx-ts-max = <512>; + snps,rx-ts-max = <512>; + }; + }; + +... |