diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/bridge')
5 files changed, 65 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index a41d280c3f9f..db680413e89c 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -12,10 +12,12 @@ following device-specific properties. Required properties: - compatible : Shall contain one or more of + - "renesas,r8a774a1-hdmi" for R8A774A1 (RZ/G2M) compatible HDMI TX - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX - - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX + - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 and RZ/G2 compatible + HDMI TX When compatible with generic versions, nodes must list the SoC-specific version corresponding to the platform first, followed by the diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt index 900a884ad9f5..c6a196d0b075 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt @@ -9,6 +9,7 @@ Required properties: - compatible : Shall contain one of - "renesas,r8a7743-lvds" for R8A7743 (RZ/G1M) compatible LVDS encoders - "renesas,r8a7744-lvds" for R8A7744 (RZ/G1N) compatible LVDS encoders + - "renesas,r8a774a1-lvds" for R8A774A1 (RZ/G2M) compatible LVDS encoders - "renesas,r8a774c0-lvds" for R8A774C0 (RZ/G2E) compatible LVDS encoders - "renesas,r8a7790-lvds" for R8A7790 (R-Car H2) compatible LVDS encoders - "renesas,r8a7791-lvds" for R8A7791 (R-Car M2-W) compatible LVDS encoders @@ -45,14 +46,24 @@ OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. Each port shall have a single endpoint. +Optional properties: + +- renesas,companion : phandle to the companion LVDS encoder. This property is + mandatory for the first LVDS encoder on D3 and E3 SoCs, and shall point to + the second encoder to be used as a companion in dual-link mode. It shall not + be set for any other LVDS encoder. + Example: lvds0: lvds@feb90000 { - compatible = "renesas,r8a7790-lvds"; - reg = <0 0xfeb90000 0 0x1c>; - clocks = <&cpg CPG_MOD 726>; - resets = <&cpg 726>; + compatible = "renesas,r8a77990-lvds"; + reg = <0 0xfeb90000 0 0x20>; + clocks = <&cpg CPG_MOD 727>; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 727>; + + renesas,companion = <&lvds1>; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt index 72d2dc6c3e6b..6e14e087c0d0 100644 --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -5,10 +5,43 @@ Required properties: - reg: i2c address of the bridge Optional properties: - - interrupts: describe the interrupt line used to inform the host + - interrupts: describe the interrupt line used to inform the host about hotplug events. - reset-gpios: OF device-tree gpio specification for RST_N pin. + HDMI audio properties: + - #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin + is wired, <1> if the both are wired. HDMI audio is + configured only if this property is found. + - sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3 + Each integer indicates which i2s pin is connected to which + audio fifo. The first integer selects i2s audio pin for the + first audio fifo#0 (HDMI channels 1&2), second for fifo#1 + (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s + pins (SD0 - SD3). Any i2s pin can be connected to any fifo, + but there can be no gaps. E.g. an i2s pin must be mapped to + fifo#0 and fifo#1 before mapping a channel to fifo#2. Default + value is <0>, describing SD0 pin beiging routed to hdmi audio + fifo #0. + - clocks: phandle and clock specifier for each clock listed in + the clock-names property + - clock-names: "mclk" + Describes SII902x MCLK input. MCLK can be used to produce + HDMI audio CTS values. This property follows + Documentation/devicetree/bindings/clock/clock-bindings.txt + consumer binding. + + If HDMI audio is configured the sii902x device becomes an I2S + and/or spdif audio codec component (e.g a digital audio sink), + that can be used in configuring a full audio devices with + simple-card or audio-graph-card binding. See their binding + documents on how to describe the way the sii902x device is + connected to the rest of the audio system: + Documentation/devicetree/bindings/sound/simple-card.txt + Documentation/devicetree/bindings/sound/audio-graph-card.txt + Note: In case of the audio-graph-card binding the used port + index should be 3. + Optional subnodes: - video input: this subnode can contain a video input port node to connect the bridge to a display controller output (See this @@ -21,6 +54,12 @@ Example: compatible = "sil,sii9022"; reg = <0x39>; reset-gpios = <&pioA 1 0>; + + #sound-dai-cells = <0>; + sil,i2s-data-lanes = < 0 1 2 >; + clocks = <&mclk>; + clock-names = "mclk"; + ports { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt index 37f0c04d5a28..d17d1e5820d7 100644 --- a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt @@ -28,6 +28,12 @@ Optional video port nodes: - port@1: Second LVDS input port - port@3: Second digital CMOS/TTL parallel output +The device can operate in single-link mode or dual-link mode. In single-link +mode, all pixels are received on port@0, and port@1 shall not contain any +endpoint. In dual-link mode, even-numbered pixels are received on port@0 and +odd-numbered pixels on port@1, and both port@0 and port@1 shall contain +endpoints. + Example: -------- diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt index e3f6aa6a214d..583c5e9dbe6b 100644 --- a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt @@ -12,6 +12,7 @@ Optional properties: (active high shutdown input) - reset-gpios: OF device-tree gpio specification for RSTX pin (active low system reset) + - toshiba,hpd-pin: TC358767 GPIO pin number to which HPD is connected to (0 or 1) - ports: the ports node can contain video interface port nodes to connect to a DPI/DSI source and to an eDP/DP sink according to [1][2]: - port@0: DSI input port |