diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display')
25 files changed, 635 insertions, 27 deletions
diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt new file mode 100644 index 000000000000..00f74bad1e95 --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt @@ -0,0 +1,112 @@ +Amlogic Meson Display Controller +================================ + +The Amlogic Meson Display controller is composed of several components +that are going to be documented below: + +DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| + | vd1 _______ _____________ _________________ | | +D |-------| |----| | | | | HDMI PLL | +D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | +R |-------| |----| Processing | | | | | + | osd2 | | | |---| Enci ----------|----|-----VDAC------| +R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| +A | osd1 | | | Blenders | | Encl ----------|----|---------------| +M |-------|______|----|____________| |________________| | | +___|__________________________________________________________|_______________| + + +VIU: Video Input Unit +--------------------- + +The Video Input Unit is in charge of the pixel scanout from the DDR memory. +It fetches the frames addresses, stride and parameters from the "Canvas" memory. +This part is also in charge of the CSC (Colorspace Conversion). +It can handle 2 OSD Planes and 2 Video Planes. + +VPP: Video Post Processing +-------------------------- + +The Video Post Processing is in charge of the scaling and blending of the +various planes into a single pixel stream. +There is a special "pre-blending" used by the video planes with a dedicated +scaler and a "post-blending" to merge with the OSD Planes. +The OSD planes also have a dedicated scaler for one of the OSD. + +VENC: Video Encoders +-------------------- + +The VENC is composed of the multiple pixel encoders : + - ENCI : Interlace Video encoder for CVBS and Interlace HDMI + - ENCP : Progressive Video Encoder for HDMI + - ENCL : LCD LVDS Encoder +The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock +tree and provides the scanout clock to the VPP and VIU. +The ENCI is connected to a single VDAC for Composite Output. +The ENCI and ENCP are connected to an on-chip HDMI Transceiver. + +Device Tree Bindings: +--------------------- + +VPU: Video Processing Unit +-------------------------- + +Required properties: +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-vpu" + - GXL (S905X, S905D) : "amlogic,meson-gxl-vpu" + - GXM (S912) : "amlogic,meson-gxm-vpu" + followed by the common "amlogic,meson-gx-vpu" +- reg: base address and size of he following memory-mapped regions : + - vpu + - hhi + - dmc +- reg-names: should contain the names of the previous memory regions +- interrupts: should contain the VENC Vsync interrupt number + +Required nodes: + +The connections to the VPU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each VPU output. + + Port 0 Port 1 +----------------------------------------- + S905 (GXBB) CVBS VDAC HDMI-TX + S905X (GXL) CVBS VDAC HDMI-TX + S905D (GXL) CVBS VDAC HDMI-TX + S912 (GXM) CVBS VDAC HDMI-TX + +Example: + +tv-connector { + compatible = "composite-video-connector"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; +}; + +vpu: vpu@d0100000 { + compatible = "amlogic,meson-gxbb-vpu"; + reg = <0x0 0xd0100000 0x0 0x100000>, + <0x0 0xc883c000 0x0 0x1000>, + <0x0 0xc8838000 0x0 0x1000>; + reg-names = "vpu", "hhi", "dmc"; + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + + /* CVBS VDAC output port */ + port@0 { + reg = <0>; + + cvbs_vdac_out: endpoint { + remote-endpoint = <&tv_connector_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index a5ea451e67fc..e2768703ac2b 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -43,6 +43,13 @@ Required properties for DPI: - port: Port node with a single endpoint connecting to the panel device, as defined in [1] +Required properties for VEC: +- compatible: Should be "brcm,bcm2835-vec" +- reg: Physical base address and length of the registers +- clocks: The core clock the unit runs on +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers @@ -92,6 +99,13 @@ dpi: dpi@7e208000 { }; }; +vec: vec@7e806000 { + compatible = "brcm,bcm2835-vec"; + reg = <0x7e806000 0x1000>; + clocks = <&clocks BCM2835_CLOCK_VEC>; + interrupts = <2 27>; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; diff --git a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt new file mode 100644 index 000000000000..164cbb15f04c --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt @@ -0,0 +1,50 @@ +Dumb RGB to VGA DAC bridge +--------------------------- + +This binding is aimed for dumb RGB to VGA DAC based bridges that do not require +any configuration. + +Required properties: + +- compatible: Must be "dumb-vga-dac" + +Required nodes: + +This device has two video ports. Their connections are modelled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for RGB input +- Video port 1 for VGA output + +Optional properties: +- vdd-supply: Power supply for DAC + +Example +------- + +bridge { + compatible = "dumb-vga-dac"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + vga_bridge_in: endpoint { + remote-endpoint = <&tcon0_out_vga>; + }; + }; + + port@1 { + reg = <1>; + + vga_bridge_out: endpoint { + remote-endpoint = <&vga_con_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt index dc1452f0d5d8..5e9a84d6e5f1 100644 --- a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt @@ -19,7 +19,9 @@ Required properties: Optional properties - reg-io-width: the width of the reg:1,4, default set to 1 if not present -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing, + if the property is omitted, a functionally reduced I2C bus + controller on DW HDMI is probed - clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" Example: diff --git a/Documentation/devicetree/bindings/display/bridge/tda998x.txt b/Documentation/devicetree/bindings/display/bridge/tda998x.txt index e178e6b9f9ee..24cc2466185a 100644 --- a/Documentation/devicetree/bindings/display/bridge/tda998x.txt +++ b/Documentation/devicetree/bindings/display/bridge/tda998x.txt @@ -21,8 +21,19 @@ Optional properties: - video-ports: 24 bits value which defines how the video controller output is wired to the TDA998x input - default: <0x230145> + - audio-ports: array of 8-bit values, 2 values per one DAI[1]. + The first value defines the DAI type: TDA998x_SPDIF or TDA998x_I2S[2]. + The second value defines the tda998x AP_ENA reg content when the DAI + in question is used. The implementation allows one or two DAIs. If two + DAIs are defined, they must be of different type. + +[1] Documentation/sound/alsa/soc/DAI.txt +[2] include/dt-bindings/display/tda998x.h + Example: +#include <dt-bindings/display/tda998x.h> + tda998x: hdmi-encoder { compatible = "nxp,tda998x"; reg = <0x70>; @@ -30,4 +41,11 @@ Example: interrupts = <27 2>; /* falling edge */ pinctrl-0 = <&pmx_camera>; pinctrl-names = "default"; + video-ports = <0x230145>; + + #sound-dai-cells = <2>; + /* DAI-format AP_ENA reg value */ + audio-ports = < TDA998x_SPDIF 0x04 + TDA998x_I2S 0x03>; + }; diff --git a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt index 2cbe32a3d0bb..54d7e31525ec 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,tfp410.txt +++ b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt @@ -6,10 +6,15 @@ Required properties: Optional properties: - powerdown-gpios: power-down gpio +- reg: I2C address. If and only if present the device node + should be placed into the i2c controller node where the + tfp410 i2c is connected to. Required nodes: -- Video port 0 for DPI input -- Video port 1 for DVI output +- Video port 0 for DPI input [1]. +- Video port 1 for DVI output [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt Example ------- diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index a2ec4c1c9382..6394ea9e3b9e 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -9,7 +9,7 @@ Required properties: - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. -- hpd-gpio: following information about the hotplug gpio pin. +- hpd-gpios: following information about the hotplug gpio pin. a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. @@ -56,7 +56,7 @@ Example: compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x100000>; interrupts = <0 95 0>; - hpd-gpio = <&gpx3 7 1>; + hpd-gpios = <&gpx3 7 1>; ddc = <&hdmi_ddc_node>; phy = <&hdmi_phy_node>; samsung,syscon-phandle = <&pmu_system_controller>; diff --git a/Documentation/devicetree/bindings/display/ht16k33.txt b/Documentation/devicetree/bindings/display/ht16k33.txt new file mode 100644 index 000000000000..8e5b30b87754 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ht16k33.txt @@ -0,0 +1,42 @@ +Holtek ht16k33 RAM mapping 16*8 LED controller driver with keyscan +------------------------------------------------------------------------------- + +Required properties: +- compatible: "holtek,ht16k33" +- reg: I2C slave address of the chip. +- interrupt-parent: A phandle pointing to the interrupt controller + serving the interrupt for this chip. +- interrupts: Interrupt specification for the key pressed interrupt. +- refresh-rate-hz: Display update interval in HZ. +- debounce-delay-ms: Debouncing interval time in milliseconds. +- linux,keymap: The keymap for keys as described in the binding + document (devicetree/bindings/input/matrix-keymap.txt). + +Optional properties: +- linux,no-autorepeat: Disable keyrepeat. +- default-brightness-level: Initial brightness level [0-15] (default: 15). + +Example: + +&i2c1 { + ht16k33: ht16k33@70 { + compatible = "holtek,ht16k33"; + reg = <0x70>; + refresh-rate-hz = <20>; + debounce-delay-ms = <50>; + interrupt-parent = <&gpio4>; + interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + linux,keymap = < + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(3, 0, KEY_F8) + MATRIX_KEY(4, 0, KEY_F10) + MATRIX_KEY(5, 0, KEY_F4) + MATRIX_KEY(6, 0, KEY_F2) + MATRIX_KEY(2, 1, KEY_F5) + MATRIX_KEY(3, 1, KEY_F7) + MATRIX_KEY(4, 1, KEY_F9) + MATRIX_KEY(5, 1, KEY_F3) + MATRIX_KEY(6, 1, KEY_F1) + >; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index b63f614e0c04..2ad578984fcf 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -14,17 +14,16 @@ Required properties: - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: device clocks See ../clocks/clock-bindings.txt for details. -- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin -- qcom,hdmi-tx-ddc-data-gpio: ddc data pin -- qcom,hdmi-tx-hpd-gpio: hpd pin - core-vdda-supply: phandle to supply regulator - hdmi-mux-supply: phandle to mux regulator - phys: the phandle for the HDMI PHY device - phy-names: the name of the corresponding PHY device Optional properties: -- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin -- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin +- hpd-gpios: hpd pin +- qcom,hdmi-tx-mux-en-gpios: hdmi mux enable pin +- qcom,hdmi-tx-mux-sel-gpios: hdmi mux select pin +- qcom,hdmi-tx-mux-lpm-gpios: hdmi mux lpm pin - power-domains: reference to the power domain(s), if available. - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) diff --git a/Documentation/devicetree/bindings/display/mxsfb.txt b/Documentation/devicetree/bindings/display/mxsfb.txt index 96ec5179c8a0..472e1ea6c591 100644 --- a/Documentation/devicetree/bindings/display/mxsfb.txt +++ b/Documentation/devicetree/bindings/display/mxsfb.txt @@ -1,20 +1,57 @@ * Freescale MXS LCD Interface (LCDIF) +New bindings: +============= Required properties: -- compatible: Should be "fsl,<chip>-lcdif". Supported chips include - imx23 and imx28. -- reg: Address and length of the register set for lcdif -- interrupts: Should contain lcdif interrupts -- display : phandle to display node (see below for details) +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. + Should be "fsl,imx6sx-lcdif" for i.MX6SX. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupt +- clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. +- clock-names: A list of clock names. For MXSFB it should contain: + - "pix" for the LCDIF block clock + - (MX6SX-only) "axi", "disp_axi" for the bus interface clock + +Required sub-nodes: + - port: The connection to an encoder chip. + +Example: + + lcdif1: display-controller@2220000 { + compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; + reg = <0x02220000 0x4000>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>, + <&clks IMX6SX_CLK_LCDIF_APB>, + <&clks IMX6SX_CLK_DISPLAY_AXI>; + clock-names = "pix", "axi", "disp_axi"; + + port { + parallel_out: endpoint { + remote-endpoint = <&panel_in_parallel>; + }; + }; + }; + +Deprecated bindings: +==================== +Required properties: +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupts +- display: phandle to display node (see below for details) * display node Required properties: -- bits-per-pixel : <16> for RGB565, <32> for RGB888/666. -- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>. +- bits-per-pixel: <16> for RGB565, <32> for RGB888/666. +- bus-width: number of data lines. Could be <8>, <16>, <18> or <24>. Required sub-node: -- display-timings : Refer to binding doc display-timing.txt for details. +- display-timings: Refer to binding doc display-timing.txt for details. Examples: diff --git a/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt b/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt new file mode 100644 index 000000000000..3afc76747824 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,g133han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g133han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt b/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt new file mode 100644 index 000000000000..ed657c2141d4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,g185han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 18.5" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g185han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt b/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt new file mode 100644 index 000000000000..cbd9da3f03b1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/auo,t215hvn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 21.5" FHD (1920x1080) color TFT LCD panel + +Required properties: +- compatible: should be "auo,t215hvn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt b/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt new file mode 100644 index 000000000000..dd22685d2adc --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/chunghwa,claa070wp03xg.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 7" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa070wp03xg" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/display-timing.txt b/Documentation/devicetree/bindings/display/panel/display-timing.txt index e1d4a0b59612..81a75893d1b8 100644 --- a/Documentation/devicetree/bindings/display/panel/display-timing.txt +++ b/Documentation/devicetree/bindings/display/panel/display-timing.txt @@ -32,6 +32,14 @@ optional properties: - active low = drive pixel data on falling edge/ sample data on rising edge - ignored = ignored + - syncclk-active: with + - active high = drive sync on rising edge/ + sample sync on falling edge of pixel + clock + - active low = drive sync on falling edge/ + sample sync on rising edge of pixel + clock + - omitted = same configuration as pixelclk-active - interlaced (bool): boolean to enable interlaced mode - doublescan (bool): boolean to enable doublescan mode - doubleclk (bool): boolean to enable doubleclock mode diff --git a/Documentation/devicetree/bindings/display/panel/innolux,g101ice-l01.txt b/Documentation/devicetree/bindings/display/panel/innolux,g101ice-l01.txt new file mode 100644 index 000000000000..9e7590465227 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,g101ice-l01.txt @@ -0,0 +1,7 @@ +Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel + +Required properties: +- compatible: should be "innolux,g101ice-l01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt new file mode 100644 index 000000000000..4989c91d505f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt @@ -0,0 +1,31 @@ +JDI model LT070ME05000 1200x1920 7" DSI Panel + +Required properties: +- compatible: should be "jdi,lt070me05000" +- vddp-supply: phandle of the regulator that provides the supply voltage + Power IC supply (3-5V) +- iovcc-supply: phandle of the regulator that provides the supply voltage + IOVCC , power supply for LCM (1.8V) +- enable-gpios: phandle of gpio for enable line + LED_EN, LED backlight enable, High active +- reset-gpios: phandle of gpio for reset line + This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names + XRES, Reset, Low active +- dcdc-en-gpios: phandle of the gpio for power ic line + Power IC supply enable, High active + +Example: + + dsi0: qcom,mdss_dsi@4700000 { + panel@0 { + compatible = "jdi,lt070me05000"; + reg = <0>; + + vddp-supply = <&pm8921_l17>; + iovcc-supply = <&pm8921_lvs7>; + + enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>; + dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/nvd,9128.txt b/Documentation/devicetree/bindings/display/panel/nvd,9128.txt new file mode 100644 index 000000000000..17bcd017c678 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/nvd,9128.txt @@ -0,0 +1,7 @@ +New Vision Display 7.0" 800 RGB x 480 TFT LCD panel + +Required properties: +- compatible: should be "nvd,9128" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt new file mode 100644 index 000000000000..0f57c3143506 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt @@ -0,0 +1,36 @@ +Sharp 15" LQ150X1LG11 XGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq150x1lg11" +- power-supply: regulator to provide the VCC supply voltage (3.3 volts) + +Optional properties: +- backlight: phandle of the backlight device +- rlud-gpios: a single GPIO for the RL/UD (rotate 180 degrees) pin. +- sellvds-gpios: a single GPIO for the SELLVDS pin. + +If rlud-gpios and/or sellvds-gpios are not specified, the RL/UD and/or SELLVDS +pins are assumed to be handled appropriately by the hardware. + +Example: + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 100000>; /* VBR */ + + brightness-levels = <0 20 40 60 80 100>; + default-brightness-level = <2>; + + power-supply = <&vdd_12v_reg>; /* VDD */ + enable-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; /* XSTABY */ + }; + + panel { + compatible = "sharp,lq150x1lg11"; + + power-supply = <&vcc_3v3_reg>; /* VCC */ + + backlight = <&backlight>; + rlud-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* RL/UD */ + sellvds-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; /* SELLVDS */ + }; diff --git a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt new file mode 100644 index 000000000000..f5e3c6f2095a --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt @@ -0,0 +1,47 @@ +TPO TPG110 Panel +================ + +This binding builds on the DPI bindings, adding a few properties +as a superset of a DPI. See panel-dpi.txt for the required DPI +bindings. + +Required properties: +- compatible : "tpo,tpg110" +- grestb-gpios : panel reset GPIO +- scen-gpios : serial control enable GPIO +- scl-gpios : serial control clock line GPIO +- sda-gpios : serial control data line GPIO + +Required nodes: +- Video port for DPI input, see panel-dpi.txt +- Panel timing for DPI setup, see panel-dpi.txt + +Example +------- + +panel { + compatible = "tpo,tpg110", "panel-dpi"; + grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>; + scen-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + scl-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + backlight = <&bl>; + + port { + nomadik_clcd_panel: endpoint { + remote-endpoint = <&nomadik_clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <33200000>; + hactive = <800>; + hback-porch = <216>; + hfront-porch = <40>; + hsync-len = <1>; + vactive = <480>; + vback-porch = <35>; + vfront-porch = <10>; + vsync-len = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index 0d30e42e40be..1a02f099a0ff 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -6,9 +6,11 @@ Required Properties: - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU + - "renesas,du-r8a7792" for R8A7792 (R-Car V2H) compatible DU - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU + - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -25,10 +27,10 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[01345] use one functional clock per channel and one clock per LVDS - encoder (if available). The functional clocks must be named "du.x" with - "x" being the channel numerical index. The LVDS clocks must be named - "lvds.x" with "x" being the LVDS encoder numerical index. + - R8A779[0123456] use one functional clock per channel and one clock per + LVDS encoder (if available). The functional clocks must be named "du.x" + with "x" being the channel numerical index. The LVDS clocks must be + named "lvds.x" with "x" being the LVDS encoder numerical index. - In addition to the functional and encoder clocks, all DU versions also support externally supplied pixel clocks. Those clocks are optional. When supplied they must be named "dclkin.x" with "x" being the input @@ -47,9 +49,11 @@ corresponding to each DU output. R8A7779 (H1) DPAD 0 DPAD 1 - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2-W) DPAD LVDS 0 - - + R8A7792 (V2H) DPAD 0 DPAD 1 - - R8A7793 (M2-N) DPAD LVDS 0 - - R8A7794 (E2) DPAD 0 DPAD 1 - - R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS + R8A7796 (M3-W) DPAD HDMI LVDS - Example: R8A7790 (R-Car H2) DU diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt index 5489b59e3d41..9eb3f0a2a078 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -6,8 +6,10 @@ buffer to an external LCD interface. Required properties: - compatible: value should be one of the following - "rockchip,rk3288-vop"; "rockchip,rk3036-vop"; + "rockchip,rk3288-vop"; + "rockchip,rk3399-vop-big"; + "rockchip,rk3399-vop-lit"; - interrupts: should contain a list of all VOP IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index df8f4aeefe4c..b82c00449468 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -26,13 +26,16 @@ TCON The TCON acts as a timing controller for RGB, LVDS and TV interfaces. Required properties: - - compatible: value should be "allwinner,sun5i-a13-tcon". + - compatible: value must be either: + * allwinner,sun5i-a13-tcon + * allwinner,sun6i-a31-tcon + * allwinner,sun6i-a31s-tcon + * allwinner,sun8i-a33-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the TCON. Three are needed: - 'ahb': the interface clocks - 'tcon-ch0': The clock driving the TCON channel 0 - - 'tcon-ch1': The clock driving the TCON channel 1 - resets: phandles to the reset controllers driving the encoder - "lcd": the reset line for the TCON channel 0 @@ -49,6 +52,35 @@ Required properties: second the block connected to the TCON channel 1 (usually the TV encoder) +On SoCs other than the A33, there is one more clock required: + - 'tcon-ch1': The clock driving the TCON channel 1 + +DRC +--- + +The DRC (Dynamic Range Controller), found in the latest Allwinner SoCs +(A31, A23, A33), allows to dynamically adjust pixel +brightness/contrast based on histogram measurements for LCD content +adaptive backlight control. + + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-drc + * allwinner,sun6i-a31s-drc + * allwinner,sun8i-a33-drc + - reg: base address and size of the memory-mapped region. + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the DRC + * ahb: the DRC interface clock + * mod: the DRC module clock + * ram: the DRC DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset line driving the DRC + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the outputs Display Engine Backend ---------------------- @@ -59,6 +91,8 @@ system. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-backend + * allwinner,sun6i-a31-display-backend + * allwinner,sun8i-a33-display-backend - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the frontend and backend * ahb: the backend interface clock @@ -71,6 +105,14 @@ Required properties: Documentation/devicetree/bindings/media/video-interfaces.txt. The first port should be the input endpoints, the second one the output +On the A33, some additional properties are required: + - reg needs to have an additional region corresponding to the SAT + - reg-names need to be set, with "be" and "sat" + - clocks and clock-names need to have a phandle to the SAT bus + clocks, whose name will be "sat" + - resets and reset-names need to have a phandle to the SAT bus + resets, whose name will be "sat" + Display Engine Frontend ----------------------- @@ -80,6 +122,8 @@ deinterlacing and color space conversion. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-frontend + * allwinner,sun6i-a31-display-frontend + * allwinner,sun8i-a33-display-frontend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the frontend and backend @@ -104,6 +148,9 @@ extra node. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-engine + * allwinner,sun6i-a31-display-engine + * allwinner,sun6i-a31s-display-engine + * allwinner,sun8i-a33-display-engine - allwinner,pipelines: list of phandle to the display engine frontends available. diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt index 2136ee81e061..6fddb4f4f71a 100644 --- a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt +++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt @@ -1,7 +1,9 @@ Device-Tree bindings for tilcdc DRM driver Required properties: - - compatible: value should be "ti,am33xx-tilcdc". + - compatible: value should be one of the following: + - "ti,am33xx-tilcdc" for AM335x based boards + - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards - interrupts: the interrupt number - reg: base address and size of the LCDC device @@ -17,6 +19,18 @@ Optional properties: the lcd controller. - max-pixelclock: The maximum pixel clock that can be supported by the lcd controller in KHz. + - blue-and-red-wiring: Recognized values "straight" or "crossed". + This property deals with the LCDC revision 2 (found on AM335x) + color errata [1]. + - "straight" indicates normal wiring that supports RGB565, + BGR888, and XBGR8888 color formats. + - "crossed" indicates wiring that has blue and red wires + crossed. This setup supports BGR565, RGB888 and XRGB8888 + formats. + - If the property is not present or its value is not recognized + the legacy mode is assumed. This configuration supports RGB565, + RGB888 and XRGB8888 formats. However, depending on wiring, the red + and blue colors are swapped in either 16 or 24-bit color modes. Optional nodes: @@ -24,15 +38,29 @@ Optional nodes: binding follows Documentation/devicetree/bindings/graph.txt and suppors a single port with a single endpoint. + - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and + Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting + tfp410 DVI encoder or lcd panel to lcdc + +[1] There is an errata about AM335x color wiring. For 16-bit color mode + the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]), + but for 24 bit color modes the wiring of blue and red components is + crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is + for Blue[3-7]. For more details see section 3.1.1 in AM335x + Silicon Errata: + http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360 + Example: fb: fb@4830e000 { - compatible = "ti,am33xx-tilcdc"; + compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc"; reg = <0x4830e000 0x1000>; interrupt-parent = <&intc>; interrupts = <36>; ti,hwmods = "lcdc"; + blue-and-red-wiring = "crossed"; + port { lcdc_0: endpoint@0 { remote-endpoint = <&hdmi_0>; diff --git a/Documentation/devicetree/bindings/display/zte,vou.txt b/Documentation/devicetree/bindings/display/zte,vou.txt new file mode 100644 index 000000000000..740e5bd2e4f7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/zte,vou.txt @@ -0,0 +1,84 @@ +ZTE VOU Display Controller + +This is a display controller found on ZTE ZX296718 SoC. It includes multiple +Graphic Layer (GL) and Video Layer (VL), two Mixers/Channels, and a few blocks +handling scaling, color space conversion etc. VOU also integrates the support +for typical output devices, like HDMI, TV Encoder, VGA, and RGB LCD. + +* Master VOU node + +It must be the parent node of all the sub-device nodes. + +Required properties: + - compatible: should be "zte,zx296718-vou" + - #address-cells: should be <1> + - #size-cells: should be <1> + - ranges: list of address translations between VOU and sub-devices + +* VOU DPC device + +Required properties: + - compatible: should be "zte,zx296718-dpc" + - reg: Physical base address and length of DPC register regions, one for each + entry in 'reg-names' + - reg-names: The names of register regions. The following regions are required: + "osd" + "timing_ctrl" + "dtrc" + "vou_ctrl" + "otfppu" + - interrupts: VOU DPC interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "aclk" + "ppu_wclk" + "main_wclk" + "aux_wclk" + +* HDMI output device + +Required properties: + - compatible: should be "zte,zx296718-hdmi" + - reg: Physical base address and length of the HDMI device IO region + - interrupts : HDMI interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "osc_cec" + "osc_clk" + "xclk" + +Example: + +vou: vou@1440000 { + compatible = "zte,zx296718-vou"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1440000 0x10000>; + + dpc: dpc@0 { + compatible = "zte,zx296718-dpc"; + reg = <0x0000 0x1000>, <0x1000 0x1000>, + <0x5000 0x1000>, <0x6000 0x1000>, + <0xa000 0x1000>; + reg-names = "osd", "timing_ctrl", + "dtrc", "vou_ctrl", + "otfppu"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topcrm VOU_ACLK>, <&topcrm VOU_PPU_WCLK>, + <&topcrm VOU_MAIN_WCLK>, <&topcrm VOU_AUX_WCLK>; + clock-names = "aclk", "ppu_wclk", + "main_wclk", "aux_wclk"; + }; + + hdmi: hdmi@c000 { + compatible = "zte,zx296718-hdmi"; + reg = <0xc000 0x4000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>; + clocks = <&topcrm HDMI_OSC_CEC>, + <&topcrm HDMI_OSC_CLK>, + <&topcrm HDMI_XCLK>; + clock-names = "osc_cec", "osc_clk", "xclk"; + }; +}; |