diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
6 files changed, 155 insertions, 43 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt new file mode 100644 index 000000000000..e0d0446a6b78 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt @@ -0,0 +1,28 @@ +Cirrus Logic CLPS711X GPIO controller + +Required properties: +- compatible: Should be "cirrus,clps711x-gpio" +- reg: Physical base GPIO controller registers location and length. + There should be two registers, first is DATA register, the second + is DIRECTION. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + gpio0 = &porta; +}; + +porta: gpio@80000000 { + compatible = "cirrus,clps711x-gpio"; + reg = <0x80000000 0x1>, <0x80000040 0x1>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/Documentation/devicetree/bindings/gpio/gpio-msm.txt new file mode 100644 index 000000000000..ac20e68a004e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-msm.txt @@ -0,0 +1,26 @@ +MSM GPIO controller bindings + +Required properties: +- compatible: + - "qcom,msm-gpio" for MSM controllers +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller +- interrupts : Specify the TLMM summary interrupt number +- ngpio : Specify the number of MSM GPIOs + +Example: + + msmgpio: gpio@fd510000 { + compatible = "qcom,msm-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0xfd510000 0x4000>; + interrupts = <0 208 0>; + ngpio = <150>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index f1e5dfecf55d..5375625e8cd2 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -39,46 +39,3 @@ Example: #gpio-cells = <4>; gpio-controller; }; - - -Samsung S3C24XX GPIO Controller - -Required properties: -- compatible: Compatible property value should be "samsung,s3c24xx-gpio". - -- reg: Physical base address of the controller and length of memory mapped - region. - -- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes - should be the following with values derived from the SoC user manual. - <[phandle of the gpio controller node] - [pin number within the gpio controller] - [mux function] - [flags and pull up/down] - - Values for gpio specifier: - - Pin number: depending on the controller a number from 0 up to 15. - - Mux function: Depending on the SoC and the gpio bank the gpio can be set - as input, output or a special function - - Flags and Pull Up/Down: the values to use differ for the individual SoCs - example S3C2416/S3C2450: - 0 - Pull Up/Down Disabled. - 1 - Pull Down Enabled. - 2 - Pull Up Enabled. - Bit 16 (0x00010000) - Input is active low. - Consult the user manual for the correct values of Mux and Pull Up/Down. - -- gpio-controller: Specifies that the node is a gpio controller. -- #address-cells: should be 1. -- #size-cells: should be 1. - -Example: - - gpa: gpio-controller@56000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "samsung,s3c24xx-gpio"; - reg = <0x56000000 0x10>; - #gpio-cells = <3>; - gpio-controller; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt b/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt new file mode 100644 index 000000000000..fd665b44d767 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt @@ -0,0 +1,7 @@ +ST-Ericsson COH 901 571/3 GPIO controller + +Required properties: +- compatible: Compatible property value should be "stericsson,gpio-coh901" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: the 0...n interrupts assigned to the different GPIO ports/banks. diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt new file mode 100644 index 000000000000..63bf4becd5f0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt @@ -0,0 +1,48 @@ +Xilinx plb/axi GPIO controller + +Dual channel GPIO controller with configurable number of pins +(from 1 to 32 per channel). Every pin can be configured as +input/output/tristate. Both channels share the same global IRQ but +local interrupts can be enabled on channel basis. + +Required properties: +- compatible : Should be "xlnx,xps-gpio-1.00.a" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the device node as a GPIO controller. + +Optional properties: +- interrupts : Interrupt mapping for GPIO IRQ. +- interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input +- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1 +- xlnx,gpio-width : gpio width +- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode +- xlnx,is-dual : if 1, controller also uses the second channel +- xlnx,all-inputs-2 : as above but for the second channel +- xlnx,dout-default-2 : as above but the second channel +- xlnx,gpio2-width : as above but for the second channel +- xlnx,tri-default-2 : as above but for the second channel + + +Example: +gpio: gpio@40000000 { + #gpio-cells = <2>; + compatible = "xlnx,xps-gpio-1.00.a"; + gpio-controller ; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 6 2 >; + reg = < 0x40000000 0x10000 >; + xlnx,all-inputs = <0x0>; + xlnx,all-inputs-2 = <0x0>; + xlnx,dout-default = <0x0>; + xlnx,dout-default-2 = <0x0>; + xlnx,gpio-width = <0x2>; + xlnx,gpio2-width = <0x2>; + xlnx,interrupt-present = <0x1>; + xlnx,is-dual = <0x1>; + xlnx,tri-default = <0xffffffff>; + xlnx,tri-default-2 = <0xffffffff>; +} ; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt new file mode 100644 index 000000000000..cb3dc7bcd8e6 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -0,0 +1,46 @@ +* Renesas R-Car GPIO Controller + +Required Properties: + + - compatible: should be one of the following. + - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller. + - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. + - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. + - "renesas,gpio-rcar": for generic R-Car GPIO controller. + + - reg: Base address and length of each memory resource used by the GPIO + controller hardware module. + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + + - gpio-controller: Marks the device node as a gpio controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. + +Please refer to gpio.txt in this directory for details of gpio-ranges property +and the common GPIO bindings used by client devices. + +Example: R8A7779 (R-Car H1) GPIO controller nodes + + gpio0: gpio@ffc40000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc40000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 141 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 32>; + }; + ... + gpio6: gpio@ffc46000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc46000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 147 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 9>; + }; |