1 files changed, 0 insertions, 80 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
deleted file mode 100644
index d4cf10582a26..000000000000
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
+++ /dev/null
@@ -1,80 +0,0 @@
-GPIO-based I2C Bus Mux
-
-This binding describes an I2C bus multiplexer that uses GPIOs to
-route the I2C signals.
-
-                                  +-----+  +-----+
-                                  | dev |  | dev |
-    +------------+                +-----+  +-----+
-    | SoC        |                   |        |
-    |            |          /--------+--------+
-    |   +------+ |  +------+    child bus A, on GPIO value set to 0
-    |   | I2C  |-|--| Mux  |
-    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
-    |            |     |    \----------+--------+--------+
-    |   +------+ |     |               |        |        |
-    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
-    |   +------+ |                  | dev |  | dev |  | dev |
-    +------------+                  +-----+  +-----+  +-----+
-
-Required properties:
-- compatible: i2c-mux-gpio
-- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
-  port is connected to.
-- mux-gpios: list of gpios used to control the muxer
-* Standard I2C mux properties. See i2c-mux.yaml in this directory.
-* I2C child bus nodes. See i2c-mux.yaml in this directory.
-
-Optional properties:
-- idle-state: value to set the muxer to when idle. When no value is
-  given, it defaults to the last value used.
-
-For each i2c child node, an I2C child bus will be created. They will
-be numbered based on their order in the device tree.
-
-Whenever an access is made to a device on a child bus, the value set
-in the relevant node's reg property will be output using the list of
-GPIOs, the first in the list holding the least-significant value.
-
-If an idle state is defined, using the idle-state (optional) property,
-whenever an access is not being made to a device on a child bus, the
-GPIOs will be set according to the idle value.
-
-If an idle state is not defined, the most recently used value will be
-left programmed into hardware whenever no access is being made to a
-device on a child bus.
-
-Example:
-	i2cmux {
-		compatible = "i2c-mux-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
-		i2c-parent = <&i2c1>;
-
-		i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ssd1307: oled@3c {
-				compatible = "solomon,ssd1307fb-i2c";
-				reg = <0x3c>;
-				pwms = <&pwm 4 3000>;
-				reset-gpios = <&gpio2 7 1>;
-			};
-		};
-
-		i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			pca9555: pca9555@20 {
-				compatible = "nxp,pca9555";
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x20>;
-			};
-		};
-	};