diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
20 files changed, 393 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 2100e9af379c..e132394375a1 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -20,6 +20,10 @@ Optional properties: - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's interrupt line in use. + - vdd-supply: phandle to the regulator that provides vdd power to the accelerometer. + + - vddio-supply: phandle to the regulator that provides vddio power to the accelerometer. + Example: mma8453fc@1d { diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt new file mode 100644 index 000000000000..d7b6241ca881 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt @@ -0,0 +1,65 @@ +Analog Devices AD7606 Simultaneous Sampling ADC + +Required properties for the AD7606: + +- compatible: Must be one of + * "adi,ad7605-4" + * "adi,ad7606-8" + * "adi,ad7606-6" + * "adi,ad7606-4" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt +- avcc-supply: phandle to the Avcc power supply +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin. + This logic input is used to initiate conversions on the analog + input channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Optional properties: + +- reset-gpios: must be the device tree identifier of the RESET pin. If specified, + it will be asserted during driver probe. As the line is active high, + it should be marked GPIO_ACTIVE_HIGH. +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used + to place the AD7606 into one of two power-down modes, Standby mode or + Shutdown mode. As the line is active low, it should be marked + GPIO_ACTIVE_LOW. +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin. + The FRSTDATA output indicates when the first channel, V1, is + being read back on either the parallel, byte or serial interface. + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on + this pin determines the input range of the analog input channels. If + this pin is tied to a logic high, the analog input range is ±10V for + all channels. If this pin is tied to a logic low, the analog input range + is ±5V for all channels. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. +- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling + mode pins. As the line is active high, it should be marked + GPIO_ACTIVE_HIGH. + +Example: + + adc@0 { + compatible = "adi,ad7606-8"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + + avcc-supply = <&adc_vref>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH + &gpio 23 GPIO_ACTIVE_HIGH + &gpio 26 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt new file mode 100644 index 000000000000..9f5b88cf680d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7768-1.txt @@ -0,0 +1,41 @@ +Analog Devices AD7768-1 ADC device driver + +Required properties for the AD7768-1: + +- compatible: Must be "adi,ad7768-1" +- reg: SPI chip select number for the device +- spi-max-frequency: Max SPI frequency to use + see: Documentation/devicetree/bindings/spi/spi-bus.txt +- clocks: phandle to the master clock (mclk) + see: Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names: Must be "mclk". +- interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- vref-supply: vref supply can be used as reference for conversion +- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables + synchronization of multiple devices that require simultaneous sampling. + A pulse is always required if the configuration is changed in any way, for example + if the filter decimation rate changes. As the line is active low, it should + be marked GPIO_ACTIVE_LOW. + +Optional properties: + + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during + driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW. + +Example: + + adc@0 { + compatible = "adi,ad7768-1"; + reg = <0>; + spi-max-frequency = <2000000>; + spi-cpol; + spi-cpha; + vref-supply = <&adc_vref>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + clocks = <&ad7768_mclk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 325090e43ce6..75c775954102 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -23,6 +23,10 @@ Required properties: - #io-channel-cells: must be 1, see ../iio-bindings.txt Optional properties: +- amlogic,hhi-sysctrl: phandle to the syscon which contains the 5th bit + of the TSC (temperature sensor coefficient) on + Meson8b and Meson8m2 (which used to calibrate the + temperature sensor) - nvmem-cells: phandle to the temperature_calib eFuse cells - nvmem-cell-names: if present (to enable the temperature sensor calibration) this must contain "temperature_calib" diff --git a/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt new file mode 100644 index 000000000000..f01159f20d87 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ingenic,adc.txt @@ -0,0 +1,48 @@ +* Ingenic JZ47xx ADC controller IIO bindings + +Required properties: + +- compatible: Should be one of: + * ingenic,jz4725b-adc + * ingenic,jz4740-adc +- reg: ADC controller registers location and length. +- clocks: phandle to the SoC's ADC clock. +- clock-names: Must be set to "adc". +- #io-channel-cells: Must be set to <1> to indicate channels are selected + by index. + +ADC clients must use the format described in iio-bindings.txt, giving +a phandle and IIO specifier pair ("io-channels") to the ADC controller. + +Example: + +#include <dt-bindings/iio/adc/ingenic,adc.h> + +adc: adc@10070000 { + compatible = "ingenic,jz4740-adc"; + #io-channel-cells = <1>; + + reg = <0x10070000 0x30>; + + clocks = <&cgu JZ4740_CLK_ADC>; + clock-names = "adc"; + + interrupt-parent = <&intc>; + interrupts = <18>; +}; + +adc-keys { + ... + compatible = "adc-keys"; + io-channels = <&adc INGENIC_ADC_AUX>; + io-channel-names = "buttons"; + ... +}; + +battery { + ... + compatible = "ingenic,jz4740-battery"; + io-channels = <&adc INGENIC_ADC_BATTERY>; + io-channel-names = "battery"; + ... +}; diff --git a/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt new file mode 100644 index 000000000000..b3629d3a9adf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/lpc32xx-adc.txt @@ -0,0 +1,16 @@ +* NXP LPC32xx SoC ADC controller + +Required properties: +- compatible: must be "nxp,lpc3220-adc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The ADC interrupt + +Example: + + adc@40048000 { + compatible = "nxp,lpc3220-adc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt new file mode 100644 index 000000000000..eb939fe77836 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton,npcm-adc.txt @@ -0,0 +1,24 @@ +Nuvoton NPCM Analog to Digital Converter (ADC) + +The NPCM ADC is a 10-bit converter for eight channel inputs. + +Required properties: +- compatible: "nuvoton,npcm750-adc" for the NPCM7XX BMC. +- reg: specifies physical base address and size of the registers. +- interrupts: Contain the ADC interrupt with flags for falling edge. + +Optional properties: +- clocks: phandle of ADC reference clock, in case the clock is not + added the ADC will use the default ADC sample rate. +- vref-supply: The regulator supply ADC reference voltage, in case the + vref-supply is not added the ADC will use internal voltage + reference. + +Example: + +adc: adc@f000c000 { + compatible = "nuvoton,npcm750-adc"; + reg = <0xf000c000 0x8>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk NPCM7XX_CLK_ADC>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt index a10c1f89037d..e1fe02f3e3e9 100644 --- a/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/samsung,exynos-adc.txt @@ -11,11 +11,13 @@ New driver handles the following Required properties: - compatible: Must be "samsung,exynos-adc-v1" - for exynos4412/5250 controllers. + for Exynos5250 controllers. Must be "samsung,exynos-adc-v2" for future controllers. Must be "samsung,exynos3250-adc" for controllers compatible with ADC of Exynos3250. + Must be "samsung,exynos4212-adc" for + controllers compatible with ADC of Exynos4212 and Exynos4412. Must be "samsung,exynos7-adc" for the ADC in Exynos7 and compatibles Must be "samsung,s3c2410-adc" for diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt new file mode 100644 index 000000000000..480e66422625 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt @@ -0,0 +1,21 @@ +STMPE ADC driver +---------------- + +Required properties: + - compatible: "st,stmpe-adc" + +Optional properties: +Note that the ADC is shared with the STMPE touchscreen. ADC related settings +have to be done in the mfd. +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be + requestable due to different usage (e.g. touch) + +Node name must be stmpe_adc and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ + }; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt new file mode 100644 index 000000000000..ecf807bb32f7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads124s08.txt @@ -0,0 +1,25 @@ +* Texas Instruments' ads124s08 and ads124s06 ADC chip + +Required properties: + - compatible : + "ti,ads124s08" + "ti,ads124s06" + - reg : spi chip select number for the device + +Recommended properties: + - spi-max-frequency : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - spi-cpha : Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - reset-gpios : GPIO pin used to reset the device. + +Example: +adc@0 { + compatible = "ti,ads124s08"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/bme680.txt b/Documentation/devicetree/bindings/iio/chemical/bme680.txt new file mode 100644 index 000000000000..7f3827cfb2ff --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/bme680.txt @@ -0,0 +1,11 @@ +Bosch Sensortec BME680 pressure/temperature/humidity/voc sensors + +Required properties: +- compatible: must be "bosch,bme680" + +Example: + +bme680@76 { + compatible = "bosch,bme680"; + reg = <0x76>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt new file mode 100644 index 000000000000..7b5f06f324c8 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt @@ -0,0 +1,20 @@ +* Plantower PMS7003 particulate matter sensor + +Required properties: +- compatible: must be "plantower,pms7003" +- vcc-supply: phandle to the regulator that provides power to the sensor + +Optional properties: +- plantower,set-gpios: phandle to the GPIO connected to the SET line +- reset-gpios: phandle to the GPIO connected to the RESET line + +Refer to serial/slave-device.txt for generic serial attached device bindings. + +Example: + +&uart0 { + air-pollution-sensor { + compatible = "plantower,pms7003"; + vcc-supply = <®_vcc5v0>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt new file mode 100644 index 000000000000..5844ed58173c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sgp30.txt @@ -0,0 +1,15 @@ +* Sensirion SGP30/SGPC3 multi-pixel Gas Sensor + +Required properties: + + - compatible: must be one of + "sensirion,sgp30" + "sensirion,sgpc3" + - reg: the I2C address of the sensor + +Example: + +gas@58 { + compatible = "sensirion,sgp30"; + reg = <0x58>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt new file mode 100644 index 000000000000..6eee2709b5b6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/sensirion,sps30.txt @@ -0,0 +1,12 @@ +* Sensirion SPS30 particulate matter sensor + +Required properties: +- compatible: must be "sensirion,sps30" +- reg: the I2C address of the sensor + +Example: + +sps30@69 { + compatible = "sensirion,sps30"; + reg = <0x69>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt new file mode 100644 index 000000000000..639c94ed83e9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac7612.txt @@ -0,0 +1,28 @@ +* Texas Instruments Dual, 12-Bit Serial Input Digital-to-Analog Converter + +The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with guaranteed +12-bit monotonicity performance over the industrial temperature range. +Is is programmable through an SPI interface. + +The internal DACs are loaded when the LOADDACS pin is pulled down. + +http://www.ti.com/lit/ds/sbas106/sbas106.pdf + +Required Properties: +- compatible: Should be one of: + "ti,dac7612" + "ti,dac7612u" + "ti,dac7612ub" +- reg: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional Properties: +- ti,loaddacs-gpios: GPIO descriptor for the LOADDACS pin. +- spi-*: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + dac@1 { + compatible = "ti,dac7612"; + reg = <0x1>; + ti,loaddacs-gpios = <&msmgpio 25 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt new file mode 100644 index 000000000000..5ff38728ff91 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/impedance-analyzer/ad5933.txt @@ -0,0 +1,26 @@ +Analog Devices AD5933/AD5934 Impedance Converter, Network Analyzer + +https://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdf +https://www.analog.com/media/en/technical-documentation/data-sheets/AD5934.pdf + +Required properties: + - compatible : should be one of + "adi,ad5933" + "adi,ad5934" + - reg : the I2C address. + - vdd-supply : The regulator supply for DVDD, AVDD1 and AVDD2 when they + are connected together. + +Optional properties: +- clocks : external clock reference. +- clock-names : must be "mclk" if clocks is set. + +Example for a I2C device node: + + impedance-analyzer@0d { + compatible = "adi,adxl345"; + reg = <0x0d>; + vdd-supply = <&vdd_supply>; + clocks = <&ref_clk>; + clock-names = "mclk"; + }; diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt index 0c1c105fb503..900c169de00f 100644 --- a/Documentation/devicetree/bindings/iio/imu/bmi160.txt +++ b/Documentation/devicetree/bindings/iio/imu/bmi160.txt @@ -9,9 +9,11 @@ Required properties: - spi-max-frequency : set maximum clock frequency (only for SPI) Optional properties: - - interrupts : interrupt mapping for IRQ, must be IRQ_TYPE_LEVEL_LOW + - interrupts : interrupt mapping for IRQ - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt input, set to "INT2" if INT2 pin should be used instead + - drive-open-drain : set if the specified interrupt pin should be configured as + open drain. If not set, defaults to push-pull. Examples: @@ -20,7 +22,7 @@ bmi160@68 { reg = <0x68>; interrupt-parent = <&gpio4>; - interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; interrupt-names = "INT1"; }; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index 6ab9a9d196b0..268bf7568e19 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -11,6 +11,7 @@ Required properties: "invensense,mpu9250" "invensense,mpu9255" "invensense,icm20608" + "invensense,icm20602" - reg : the I2C address of the sensor - interrupts: interrupt mapping for IRQ. It should be configured with flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or diff --git a/Documentation/devicetree/bindings/iio/light/max44009.txt b/Documentation/devicetree/bindings/iio/light/max44009.txt new file mode 100644 index 000000000000..4a98848e35c0 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/max44009.txt @@ -0,0 +1,24 @@ +* MAX44009 Ambient Light Sensor + +Required properties: + +- compatible: should be "maxim,max44009" +- reg: the I2C address of the device (default is <0x4a>) + +Optional properties: + +- interrupts: interrupt mapping for GPIO IRQ. Should be configured with + IRQ_TYPE_EDGE_FALLING. + +Refer to interrupt-controller/interrupts.txt for generic interrupt client +node bindings. + +Example: + +light-sensor@4a { + compatible = "maxim,max44009"; + reg = <0x4a>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index ddcb95509599..52ee4baec6f0 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -77,3 +77,4 @@ Pressure sensors: - st,lps22hb-press - st,lps33hw - st,lps35hw +- st,lps22hh |