diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input')
4 files changed, 83 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/keys.txt b/Documentation/devicetree/bindings/input/keys.txt new file mode 100644 index 000000000000..f5a5ddde53f1 --- /dev/null +++ b/Documentation/devicetree/bindings/input/keys.txt @@ -0,0 +1,8 @@ +General Keys Properties: + +Optional properties for Keys: +- power-off-time-sec: Duration in seconds which the key should be kept + pressed for device to power off automatically. Device with key pressed + shutdown feature can specify this property. +- linux,keycodes: Specifies the numeric keycode values to be used for + reporting key presses. diff --git a/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt index 07bf55f6e0b9..34ab5763f494 100644 --- a/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt +++ b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt @@ -7,6 +7,7 @@ PROPERTIES Value type: <string> Definition: must be one of: "qcom,pm8941-pwrkey" + "qcom,pm8941-resin" - reg: Usage: required @@ -32,6 +33,14 @@ PROPERTIES Definition: presence of this property indicates that the KPDPWR_N pin should be configured for pull up. +- linux,code: + Usage: optional + Value type: <u32> + Definition: The input key-code associated with the power key. + Use the linux event codes defined in + include/dt-bindings/input/linux-event-codes.h + When property is omitted KEY_POWER is assumed. + EXAMPLE pwrkey@800 { @@ -40,4 +49,5 @@ EXAMPLE interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; debounce = <15625>; bias-pull-up; + linux,code = <KEY_POWER>; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt new file mode 100644 index 000000000000..8daa0e868a8f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21029.txt @@ -0,0 +1,35 @@ +* Rohm BU21029 Touch Screen Controller + +Required properties: + - compatible : must be "rohm,bu21029" + - reg : i2c device address of the chip (0x40 or 0x41) + - interrupt-parent : the phandle for the gpio controller + - interrupts : (gpio) interrupt to which the chip is connected + - rohm,x-plate-ohms : x-plate resistance in Ohm + +Optional properties: + - reset-gpios : gpio pin to reset the chip (active low) + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-max-pressure: maximum pressure value + - vdd-supply : power supply for the controller + +Example: + + &i2c1 { + /* ... */ + + bu21029: bu21029@40 { + compatible = "rohm,bu21029"; + reg = <0x40>; + interrupt-parent = <&gpio1>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; + rohm,x-plate-ohms = <600>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-max-pressure = <4095>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/eeti.txt b/Documentation/devicetree/bindings/input/touchscreen/eeti.txt new file mode 100644 index 000000000000..32b3712c916e --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/eeti.txt @@ -0,0 +1,30 @@ +Bindings for EETI touchscreen controller + +Required properties: +- compatible: should be "eeti,exc3000-i2c" +- reg: I2C address of the chip. Should be set to <0xa> +- interrupts: interrupt to which the chip is connected + +Optional properties: +- attn-gpios: A handle to a GPIO to check whether interrupt is still + latched. This is necessary for platforms that lack + support for level-triggered IRQs. + +The following optional properties described in touchscreen.txt are +also supported: + +- touchscreen-inverted-x +- touchscreen-inverted-y +- touchscreen-swapped-x-y + +Example: + +i2c-master { + touchscreen@a { + compatible = "eeti,exc3000-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio>; + interrupts = <123 IRQ_TYPE_EDGE_RISING>; + attn-gpios = <&gpio 123 GPIO_ACTIVE_HIGH>; + }; +}; |