diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/s2mps11.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/s2mps11.txt | 50 |
1 files changed, 37 insertions, 13 deletions
diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 15ee89c3cc7b..d81ba30c0d8b 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11 Voltage and Current Regulator +* Samsung S2MPS11 and S2MPS14 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,7 +7,7 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic". +- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps14-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: @@ -16,20 +16,25 @@ Optional properties: - interrupts: Interrupt specifiers for interrupt sources. Optional nodes: -- clocks: s2mps11 provides three(AP/CP/BT) buffered 32.768 KHz outputs, so to - register these as clocks with common clock framework instantiate a sub-node - named "clocks". It uses the common clock binding documented in : +- clocks: s2mps11 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz + outputs, so to register these as clocks with common clock framework + instantiate a sub-node named "clocks". It uses the common clock binding + documented in : [Documentation/devicetree/bindings/clock/clock-bindings.txt] + The s2mps14 provides two (AP/BT) buffered 32.768 KHz outputs. - #clock-cells: should be 1. - The following is the list of clocks generated by the controller. Each clock is assigned an identifier and client nodes use this identifier to specify the clock which they consume. - Clock ID - ---------------------- - 32KhzAP 0 - 32KhzCP 1 - 32KhzBT 2 + Clock ID Devices + ---------------------------------------------------------- + 32KhzAP 0 S2MPS11, S2MPS14, S5M8767 + 32KhzCP 1 S2MPS11, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS14, S5M8767 + + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps14-clk", + "samsung,s5m8767-clk" - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -51,6 +56,20 @@ for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], BUCK[3, 4], and BUCK[7, 8, 10] +On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control +over GPIO. To turn this feature on this property must be added to the regulator +sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable); +Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + The regulator constraints inside the regulator nodes use the standard regulator bindings which are documented elsewhere. @@ -59,10 +78,14 @@ supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number as per the datasheet of s2mps11. - LDOn - - valid values for n are 1 to 38 + - valid values for n are: + - S2MPS11: 1 to 38 + - S2MPS14: 1 to 25 - Example: LDO1, LD02, LDO28 - BUCKn - - valid values for n are 1 to 10. + - valid values for n are: + - S2MPS11: 1 to 10 + - S2MPS14: 1 to 5 - Example: BUCK1, BUCK2, BUCK9 Example: @@ -71,7 +94,8 @@ Example: compatible = "samsung,s2mps11-pmic"; reg = <0x66>; - s2m_osc: clocks{ + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; #clock-cells = 1; clock-output-names = "xx", "yy", "zz"; }; |