diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
-rw-r--r-- | Documentation/devicetree/bindings/mfd/max77686.txt | 14 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/mfd/max77693.txt | 45 |
2 files changed, 59 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 75fdfaf41831..e39f0bc1f55e 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -39,6 +39,12 @@ to get matched with their hardware counterparts as follow: -BUCKn : 1-4. Use standard regulator bindings for it ('regulator-off-in-suspend'). + LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable + control. To turn this feature on this property must be added to the regulator + sub-node: + - maxim,ena-gpios : one GPIO specifier enable control (the gpio + flags are actually ignored and always + ACTIVE_HIGH is used) Example: @@ -65,4 +71,12 @@ Example: regulator-always-on; regulator-boot-on; }; + + buck9_reg { + regulator-compatible = "BUCK9"; + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; + }; } diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 01e9f30fe678..38e64405e98d 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -41,6 +41,41 @@ Optional properties: To get more informations, please refer to documentaion. [*] refer Documentation/devicetree/bindings/pwm/pwm.txt +- charger : Node configuring the charger driver. + If present, required properties: + - compatible : Must be "maxim,max77693-charger". + + Optional properties (if not set, defaults will be used): + - maxim,constant-microvolt : Battery constant voltage in uV. The charger + will operate in fast charge constant current mode till battery voltage + reaches this level. Then the charger will switch to fast charge constant + voltage mode. Also vsys (system voltage) will be set to this value when + DC power is supplied but charger is not enabled. + Valid values: 3650000 - 4400000, step by 25000 (rounded down) + Default: 4200000 + + - maxim,min-system-microvolt : Minimal system voltage in uV. + Valid values: 3000000 - 3700000, step by 100000 (rounded down) + Default: 3600000 + + - maxim,thermal-regulation-celsius : Temperature in Celsius for entering + high temperature charging mode. If die temperature exceeds this value + the charging current will be reduced by 105 mA/Celsius. + Valid values: 70, 85, 100, 115 + Default: 100 + + - maxim,battery-overcurrent-microamp : Overcurrent protection threshold + in uA (current from battery to system). + Valid values: 2000000 - 3500000, step by 250000 (rounded down) + Default: 3500000 + + - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for + triggering input voltage regulation loop. If input voltage decreases + below this value, the input current will be reduced to reach the + threshold voltage. + Valid values: 4300000, 4700000, 4800000, 4900000 + Default: 4300000 + Example: max77693@66 { compatible = "maxim,max77693"; @@ -73,4 +108,14 @@ Example: pwms = <&pwm 0 40000 0>; pwm-names = "haptic"; }; + + charger { + compatible = "maxim,max77693-charger"; + + maxim,constant-microvolt = <4200000>; + maxim,min-system-microvolt = <3600000>; + maxim,thermal-regulation-celsius = <75>; + maxim,battery-overcurrent-microamp = <3000000>; + maxim,charge-input-threshold-microvolt = <4300000>; + }; }; |