diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/can')
| -rw-r--r-- | Documentation/devicetree/bindings/net/can/fsl-flexcan.txt | 10 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/can/tcan4x5x.txt | 37 |
2 files changed, 47 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index bc77477c6878..94c0f8bf4deb 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -32,6 +32,15 @@ Optional properties: ack_gpr is the gpr register offset of CAN stop acknowledge. ack_bit is the bit offset of CAN stop acknowledge. +- fsl,clk-source: Select the clock source to the CAN Protocol Engine (PE). + It's SoC Implementation dependent. Refer to RM for detailed + definition. If this property is not set in device tree node + then driver selects clock source 1 by default. + 0: clock source 0 (oscillator clock) + 1: clock source 1 (peripheral clock) + +- wakeup-source: enable CAN remote wakeup + Example: can@1c000 { @@ -40,4 +49,5 @@ Example: interrupts = <48 0x2>; interrupt-parent = <&mpic>; clock-frequency = <200000000>; // filled in by bootloader + fsl,clk-source = <0>; // select clock source 0 for PE }; diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt new file mode 100644 index 000000000000..c388f7d9feb1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt @@ -0,0 +1,37 @@ +Texas Instruments TCAN4x5x CAN Controller +================================================ + +This file provides device node information for the TCAN4x5x interface contains. + +Required properties: + - compatible: "ti,tcan4x5x" + - reg: 0 + - #address-cells: 1 + - #size-cells: 0 + - spi-max-frequency: Maximum frequency of the SPI bus the chip can + operate at should be less than or equal to 18 MHz. + - data-ready-gpios: Interrupt GPIO for data and error reporting. + - device-wake-gpios: Wake up GPIO to wake up the TCAN device. + +See Documentation/devicetree/bindings/net/can/m_can.txt for additional +required property details. + +Optional properties: + - reset-gpios: Hardwired output GPIO. If not defined then software + reset. + - device-state-gpios: Input GPIO that indicates if the device is in + a sleep state or if the device is active. + +Example: +tcan4x5x: tcan4x5x@0 { + compatible = "ti,tcan4x5x"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <10000000>; + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; +}; |