1 files changed, 1 insertions, 67 deletions
diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt
index e88c3641d613..5df413d01be2 100644
--- a/Documentation/devicetree/bindings/net/ethernet.txt
+++ b/Documentation/devicetree/bindings/net/ethernet.txt
@@ -1,67 +1 @@
-The following properties are common to the Ethernet controllers:
-
-NOTE: All 'phy*' properties documented below are Ethernet specific. For the
-generic PHY 'phys' property, see
-Documentation/devicetree/bindings/phy/phy-bindings.txt.
-
-- mac-address: array of 6 bytes, specifies the MAC address that was last used by
-  the boot program; should be used in cases where the MAC address assigned to
-  the device by the boot program is different from the "local-mac-address"
-  property;
-- local-mac-address: array of 6 bytes, specifies the MAC address that was
-  assigned to the network device;
-- nvmem-cells: phandle, reference to an nvmem node for the MAC address
-- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
-- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
-- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
-  the maximum frame size (there's contradiction in the Devicetree
-  Specification).
-- phy-mode: string, operation mode of the PHY interface. This is now a de-facto
-  standard property; supported values are:
-  * "internal" (Internal means there is not a standard bus between the MAC and
-     the PHY, something proprietary is being used to embed the PHY in the MAC.)
-  * "mii"
-  * "gmii"
-  * "sgmii"
-  * "qsgmii"
-  * "tbi"
-  * "rev-mii"
-  * "rmii"
-  * "rgmii" (RX and TX delays are added by the MAC when required)
-  * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the
-     MAC should not add the RX or TX delays in this case)
-  * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
-     should not add an RX delay in this case)
-  * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC
-     should not add an TX delay in this case)
-  * "rtbi"
-  * "smii"
-  * "xgmii"
-  * "trgmii"
-  * "1000base-x",
-  * "2500base-x",
-  * "rxaui"
-  * "xaui"
-  * "10gbase-kr" (10GBASE-KR, XFI, SFI)
-- phy-connection-type: the same as "phy-mode" property but described in the
-  Devicetree Specification;
-- phy-handle: phandle, specifies a reference to a node representing a PHY
-  device; this property is described in the Devicetree Specification and so
-  preferred;
-- phy: the same as "phy-handle" property, not recommended for new bindings.
-- phy-device: the same as "phy-handle" property, not recommended for new
-  bindings.
-- rx-fifo-depth: the size of the controller's receive fifo in bytes. This
-  is used for components that can have configurable receive fifo sizes,
-  and is useful for determining certain configuration settings such as
-  flow control thresholds.
-- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This
-  is used for components that can have configurable fifo sizes.
-- managed: string, specifies the PHY management type. Supported values are:
-  "auto", "in-band-status". "auto" is the default, it usess MDIO for
-  management if fixed-link is not specified.
-
-Child nodes of the Ethernet controller are typically the individual PHY devices
-connected via the MDIO bus (sometimes the MDIO bus controller is separate).
-They are described in the phy.txt file in this same directory.
-For non-MDIO PHY management see fixed-link.txt.
+This file has moved to ethernet-controller.yaml.