diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
51 files changed, 1577 insertions, 794 deletions
diff --git a/Documentation/devicetree/bindings/net/adi,adin1110.yaml b/Documentation/devicetree/bindings/net/adi,adin1110.yaml new file mode 100644 index 000000000000..b6bd8ee38a18 --- /dev/null +++ b/Documentation/devicetree/bindings/net/adi,adin1110.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/adi,adin1110.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADI ADIN1110 MAC-PHY + +maintainers: + - Alexandru Tachici <alexandru.tachici@analog.com> + +description: | + The ADIN1110 is a low power single port 10BASE-T1L MAC- + PHY designed for industrial Ethernet applications. It integrates + an Ethernet PHY core with a MAC and all the associated analog + circuitry, input and output clock buffering. + + The ADIN2111 is a low power, low complexity, two-Ethernet ports + switch with integrated 10BASE-T1L PHYs and one serial peripheral + interface (SPI) port. The device is designed for industrial Ethernet + applications using low power constrained nodes and is compliant + with the IEEE 802.3cg-2019 Ethernet standard for long reach + 10 Mbps single pair Ethernet (SPE). + + The device has a 4-wire SPI interface for communication + between the MAC and host processor. + +allOf: + - $ref: ethernet-controller.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + enum: + - adi,adin1110 + - adi,adin2111 + + reg: + maxItems: 1 + + adi,spi-crc: + description: | + Enable CRC8 checks on SPI read/writes. + type: boolean + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + + #address-cells = <1>; + #size-cells = <0>; + + ethernet@0 { + compatible = "adi,adin2111"; + reg = <0>; + spi-max-frequency = <24500000>; + + adi,spi-crc; + + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_LEVEL_LOW>; + + local-mac-address = [ 00 11 22 33 44 55 ]; + }; + }; diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt deleted file mode 100644 index 1d9148ff5130..000000000000 --- a/Documentation/devicetree/bindings/net/altera_tse.txt +++ /dev/null @@ -1,113 +0,0 @@ -* Altera Triple-Speed Ethernet MAC driver (TSE) - -Required properties: -- compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should - be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE. - ALTR is supported for legacy device trees, but is deprecated. - altr should be used for all new designs. -- reg: Address and length of the register set for the device. It contains - the information of registers in the same order as described by reg-names -- reg-names: Should contain the reg names - "control_port": MAC configuration space region - "tx_csr": xDMA Tx dispatcher control and status space region - "tx_desc": MSGDMA Tx dispatcher descriptor space region - "rx_csr" : xDMA Rx dispatcher control and status space region - "rx_desc": MSGDMA Rx dispatcher descriptor space region - "rx_resp": MSGDMA Rx dispatcher response space region - "s1": SGDMA descriptor memory -- interrupts: Should contain the TSE interrupts and its mode. -- interrupt-names: Should contain the interrupt names - "rx_irq": xDMA Rx dispatcher interrupt - "tx_irq": xDMA Tx dispatcher interrupt -- rx-fifo-depth: MAC receive FIFO buffer depth in bytes -- tx-fifo-depth: MAC transmit FIFO buffer depth in bytes -- phy-mode: See ethernet.txt in the same directory. -- phy-handle: See ethernet.txt in the same directory. -- phy-addr: See ethernet.txt in the same directory. A configuration should - include phy-handle or phy-addr. -- altr,has-supplementary-unicast: - If present, TSE supports additional unicast addresses. - Otherwise additional unicast addresses are not supported. -- altr,has-hash-multicast-filter: - If present, TSE supports a hash based multicast filter. - Otherwise, hash-based multicast filtering is not supported. - -- mdio device tree subnode: When the TSE has a phy connected to its local - mdio, there must be device tree subnode with the following - required properties: - - - compatible: Must be "altr,tse-mdio". - - #address-cells: Must be <1>. - - #size-cells: Must be <0>. - - For each phy on the mdio bus, there must be a node with the following - fields: - - - reg: phy id used to communicate to phy. - - device_type: Must be "ethernet-phy". - -The MAC address will be determined using the optional properties defined in -ethernet.txt. - -Example: - - tse_sub_0_eth_tse_0: ethernet@1,00000000 { - compatible = "altr,tse-msgdma-1.0"; - reg = <0x00000001 0x00000000 0x00000400>, - <0x00000001 0x00000460 0x00000020>, - <0x00000001 0x00000480 0x00000020>, - <0x00000001 0x000004A0 0x00000008>, - <0x00000001 0x00000400 0x00000020>, - <0x00000001 0x00000420 0x00000020>; - reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; - interrupt-parent = <&hps_0_arm_gic_0>; - interrupts = <0 41 4>, <0 40 4>; - interrupt-names = "rx_irq", "tx_irq"; - rx-fifo-depth = <2048>; - tx-fifo-depth = <2048>; - address-bits = <48>; - max-frame-size = <1500>; - local-mac-address = [ 00 00 00 00 00 00 ]; - phy-mode = "gmii"; - altr,has-supplementary-unicast; - altr,has-hash-multicast-filter; - phy-handle = <&phy0>; - mdio { - compatible = "altr,tse-mdio"; - #address-cells = <1>; - #size-cells = <0>; - phy0: ethernet-phy@0 { - reg = <0x0>; - device_type = "ethernet-phy"; - }; - - phy1: ethernet-phy@1 { - reg = <0x1>; - device_type = "ethernet-phy"; - }; - - }; - }; - - tse_sub_1_eth_tse_0: ethernet@1,00001000 { - compatible = "altr,tse-msgdma-1.0"; - reg = <0x00000001 0x00001000 0x00000400>, - <0x00000001 0x00001460 0x00000020>, - <0x00000001 0x00001480 0x00000020>, - <0x00000001 0x000014A0 0x00000008>, - <0x00000001 0x00001400 0x00000020>, - <0x00000001 0x00001420 0x00000020>; - reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; - interrupt-parent = <&hps_0_arm_gic_0>; - interrupts = <0 43 4>, <0 42 4>; - interrupt-names = "rx_irq", "tx_irq"; - rx-fifo-depth = <2048>; - tx-fifo-depth = <2048>; - address-bits = <48>; - max-frame-size = <1500>; - local-mac-address = [ 00 00 00 00 00 00 ]; - phy-mode = "gmii"; - altr,has-supplementary-unicast; - altr,has-hash-multicast-filter; - phy-handle = <&phy1>; - }; diff --git a/Documentation/devicetree/bindings/net/altr,tse.yaml b/Documentation/devicetree/bindings/net/altr,tse.yaml new file mode 100644 index 000000000000..8d1d94494349 --- /dev/null +++ b/Documentation/devicetree/bindings/net/altr,tse.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/altr,tse.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Altera Triple Speed Ethernet MAC driver (TSE) + +maintainers: + - Maxime Chevallier <maxime.chevallier@bootlin.com> + +properties: + compatible: + oneOf: + - const: altr,tse-1.0 + - const: ALTR,tse-1.0 + deprecated: true + - const: altr,tse-msgdma-1.0 + + interrupts: + minItems: 2 + + interrupt-names: + items: + - const: rx_irq + - const: tx_irq + + rx-fifo-depth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Depth in bytes of the RX FIFO + + tx-fifo-depth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Depth in bytes of the TX FIFO + + altr,has-supplementary-unicast: + type: boolean + description: + If present, TSE supports additional unicast addresses. + + altr,has-hash-multicast-filter: + type: boolean + description: + If present, TSE supports hash based multicast filter. + + mdio: + $ref: mdio.yaml# + unevaluatedProperties: false + description: + Creates and registers an MDIO bus. + + properties: + compatible: + const: altr,tse-mdio + + required: + - compatible + +required: + - compatible + - reg + - interrupts + - rx-fifo-depth + - tx-fifo-depth + +allOf: + - $ref: "ethernet-controller.yaml#" + - if: + properties: + compatible: + contains: + enum: + - const: altr,tse-1.0 + - const: ALTR,tse-1.0 + then: + properties: + reg: + minItems: 4 + reg-names: + items: + - const: control_port + - const: rx_csr + - const: tx_csr + - const: s1 + + - if: + properties: + compatible: + contains: + enum: + - altr,tse-msgdma-1.0 + then: + properties: + reg: + minItems: 6 + maxItems: 7 + reg-names: + minItems: 6 + items: + - const: control_port + - const: rx_csr + - const: rx_desc + - const: rx_resp + - const: tx_csr + - const: tx_desc + - const: pcs + +unevaluatedProperties: false + +examples: + - | + tse_sub_0: ethernet@c0100000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0xc0100000 0x00000400>, + <0xc0101000 0x00000020>, + <0xc0102000 0x00000020>, + <0xc0103000 0x00000008>, + <0xc0104000 0x00000020>, + <0xc0105000 0x00000020>, + <0xc0106000 0x00000100>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc", "pcs"; + interrupt-parent = <&intc>; + interrupts = <0 44 4>,<0 45 4>; + interrupt-names = "rx_irq","tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + sfp = <&sfp0>; + phy-mode = "sgmii"; + managed = "in-band-status"; + }; + - | + tse_sub_1_eth_tse_0: ethernet@1,00001000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00001000 0x00000400>, + <0x00001460 0x00000020>, + <0x00001480 0x00000020>, + <0x000014A0 0x00000008>, + <0x00001400 0x00000020>, + <0x00001420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 43 4>, <0 42 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy1>; + mdio { + compatible = "altr,tse-mdio"; + #address-cells = <1>; + #size-cells = <0>; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml index 608e1d62bed5..ddd5a073c3a8 100644 --- a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml @@ -8,7 +8,7 @@ $schema: "http://devicetree.org/meta-schemas/core.yaml#" title: Amlogic Meson DWMAC Ethernet controller maintainers: - - Neil Armstrong <narmstrong@baylibre.com> + - Neil Armstrong <neil.armstrong@linaro.org> - Martin Blumenstingl <martin.blumenstingl@googlemail.com> # We need a select here so we don't match all nodes with 'snps,dwmac' diff --git a/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml b/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml index b1327c5b86cf..144a3785132c 100644 --- a/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml +++ b/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml @@ -30,8 +30,10 @@ properties: clocks: maxItems: 1 + power-domains: + maxItems: 1 + reg-io-width: - $ref: /schemas/types.yaml#/definitions/uint32 description: I/O register width (in bytes) implemented by this device default: 1 enum: [ 1, 2, 4 ] @@ -105,6 +107,7 @@ allOf: then: required: - clocks + - power-domains unevaluatedProperties: false @@ -129,4 +132,5 @@ examples: reg-io-width = <4>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; clocks = <&sysctrl R9A06G032_HCLK_CAN0>; + power-domains = <&sysctrl>; }; diff --git a/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml index cc01b9b5752a..253b5d1407ee 100644 --- a/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml +++ b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml @@ -37,6 +37,7 @@ properties: patternProperties: "^ethernet-port@[0-9]+$": type: object + unevaluatedProperties: false description: contains the resources for ethernet port allOf: - $ref: ethernet-controller.yaml# diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt index 320607cbbb17..f824fdae0da2 100644 --- a/Documentation/devicetree/bindings/net/dsa/ar9331.txt +++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt @@ -76,7 +76,6 @@ eth1: ethernet@1a000000 { switch_port0: port@0 { reg = <0x0>; - label = "cpu"; ethernet = <ð1>; phy-mode = "gmii"; diff --git a/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml b/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml index 3f01b65f3b22..259a0c6547f3 100644 --- a/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml +++ b/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml @@ -61,8 +61,9 @@ examples: }; ethernet-port@3 { reg = <3>; - label = "cpu"; ethernet = <&fec1>; + phy-mode = "rgmii-id"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml b/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml index 23114d691d2a..1219b830b1a4 100644 --- a/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml +++ b/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml @@ -169,7 +169,6 @@ examples: port@8 { reg = <8>; - label = "cpu"; phy-mode = "rgmii-txid"; ethernet = <ð0>; fixed-link { @@ -252,8 +251,9 @@ examples: port@8 { ethernet = <&amac2>; - label = "cpu"; reg = <8>; + phy-mode = "internal"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml index 09317e16cb5d..10ad7e71097b 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml @@ -76,6 +76,23 @@ properties: required: - reg +# CPU and DSA ports must have phylink-compatible link descriptions +if: + oneOf: + - required: [ ethernet ] + - required: [ link ] +then: + allOf: + - required: + - phy-mode + - oneOf: + - required: + - fixed-link + - required: + - phy-handle + - required: + - managed + additionalProperties: true ... diff --git a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml index 228683773151..73b774eadd0b 100644 --- a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml +++ b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml @@ -91,8 +91,13 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac0>; + phy-mode = "mii"; + + fixed-link { + speed = <100>; + full-duplex; + }; }; port@2 { diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt index 464d6bf87605..46a732087f5c 100644 --- a/Documentation/devicetree/bindings/net/dsa/lan9303.txt +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -46,7 +46,6 @@ I2C managed mode: port@0 { /* RMII fixed link to master */ reg = <0>; - label = "cpu"; ethernet = <&master>; }; @@ -83,7 +82,6 @@ MDIO managed mode: port@0 { reg = <0>; - label = "cpu"; ethernet = <&master>; }; diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt index e3829d3e480e..8bb1eff21cb1 100644 --- a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -96,7 +96,6 @@ switch@e108000 { port@6 { reg = <0x6>; - label = "cpu"; ethernet = <ð0>; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml index 17ab6c69ecc7..f2e9ff3f580b 100644 --- a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +++ b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml @@ -4,67 +4,92 @@ $id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7530 Ethernet switch +title: Mediatek MT7530 and MT7531 Ethernet Switches maintainers: - - Sean Wang <sean.wang@mediatek.com> + - Arınç ÃœNAL <arinc.unal@arinc9.com> - Landen Chao <Landen.Chao@mediatek.com> - DENG Qingfang <dqfext@gmail.com> + - Sean Wang <sean.wang@mediatek.com> description: | - Port 5 of mt7530 and mt7621 switch is muxed between: - 1. GMAC5: GMAC5 can interface with another external MAC or PHY. - 2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC - of the SOC. Used in many setups where port 0/4 becomes the WAN port. - Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to - GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not - connected to external component! - - Port 5 modes/configurations: - 1. Port 5 is disabled and isolated: An external phy can interface to the 2nd - GMAC of the SOC. - In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd - GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! - 2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. - It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode - and RGMII delay. - 3. Port 5 is muxed to GMAC5 and can interface to an external phy. - Port 5 becomes an extra switch port. - Only works on platform where external phy TX<->RX lines are swapped. - Like in the Ubiquiti ER-X-SFP. - 4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. - Currently a 2nd CPU port is not supported by DSA code. - - Depending on how the external PHY is wired: - 1. normal: The PHY can only connect to 2nd GMAC but not to the switch - 2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as - a ethernet port. But can't interface to the 2nd GMAC. - - Based on the DT the port 5 mode is configured. - - Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. - When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. - phy-mode must be set, see also example 2 below! - * mt7621: phy-mode = "rgmii-txid"; - * mt7623: phy-mode = "rgmii"; - - CPU-Ports need a phy-mode property: - Allowed values on mt7530 and mt7621: - - "rgmii" - - "trgmii" - On mt7531: - - "1000base-x" - - "2500base-x" - - "rgmii" - - "sgmii" + There are two versions of MT7530, standalone and in a multi-chip module. + + MT7530 is a part of the multi-chip module in MT7620AN, MT7620DA, MT7620DAN, + MT7620NN, MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs. + + MT7530 in MT7620AN, MT7620DA, MT7620DAN and MT7620NN SoCs has got 10/100 PHYs + and the switch registers are directly mapped into SoC's memory map rather than + using MDIO. The DSA driver currently doesn't support this. + + There is only the standalone version of MT7531. + + Port 5 on MT7530 has got various ways of configuration. + + For standalone MT7530: + + - Port 5 can be used as a CPU port. + + - PHY 0 or 4 of the switch can be muxed to connect to the gmac of the SoC + which port 5 is wired to. Usually used for connecting the wan port + directly to the CPU to achieve 2 Gbps routing in total. + + The driver looks up the reg on the ethernet-phy node which the phy-handle + property refers to on the gmac node to mux the specified phy. + + The driver requires the gmac of the SoC to have "mediatek,eth-mac" as the + compatible string and the reg must be 1. So, for now, only gmac1 of an + MediaTek SoC can benefit this. Banana Pi BPI-R2 suits this. + Check out example 5 for a similar configuration. + + - Port 5 can be wired to an external phy. Port 5 becomes a DSA slave. + Check out example 7 for a similar configuration. + + For multi-chip module MT7530: + + - Port 5 can be used as a CPU port. + + - PHY 0 or 4 of the switch can be muxed to connect to gmac1 of the SoC. + Usually used for connecting the wan port directly to the CPU to achieve 2 + Gbps routing in total. + + The driver looks up the reg on the ethernet-phy node which the phy-handle + property refers to on the gmac node to mux the specified phy. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + Check out example 5. + + - In case of an external phy wired to gmac1 of the SoC, port 5 must not be + enabled. + + In case of muxing PHY 0 or 4, the external phy must not be enabled. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + Check out example 6. + - Port 5 can be muxed to an external phy. Port 5 becomes a DSA slave. + The external phy must be wired TX to TX to gmac1 of the SoC for this to + work. Ubiquiti EdgeRouter X SFP is wired this way. + + Muxing PHY 0 or 4 won't work when the external phy is connected TX to TX. + + For the MT7621 SoCs, rgmii2 group must be claimed with gpio function. + Check out example 7. properties: compatible: - enum: - - mediatek,mt7530 - - mediatek,mt7531 - - mediatek,mt7621 + oneOf: + - description: + Standalone MT7530 and multi-chip module MT7530 in MT7623AI SoC + const: mediatek,mt7530 + + - description: + Standalone MT7531 + const: mediatek,mt7531 + + - description: + Multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + const: mediatek,mt7621 reg: maxItems: 1 @@ -79,7 +104,14 @@ properties: gpio-controller: type: boolean description: - if defined, MT7530's LED controller will run on GPIO mode. + If defined, LED controller of the MT7530 switch will run on GPIO mode. + + There are 15 controllable pins. + port 0 LED 0..2 as GPIO 0..2 + port 1 LED 0..2 as GPIO 3..5 + port 2 LED 0..2 as GPIO 6..8 + port 3 LED 0..2 as GPIO 9..11 + port 4 LED 0..2 as GPIO 12..14 "#interrupt-cells": const: 1 @@ -92,17 +124,21 @@ properties: io-supply: description: Phandle to the regulator node necessary for the I/O power. - See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt - for details for the regulator setup on these boards. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for + details for the regulator setup on these boards. mediatek,mcm: type: boolean description: - if defined, indicates that either MT7530 is the part on multi-chip - module belong to MT7623A has or the remotely standalone chip as the - function MT7623N reference board provided for. + Used for MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs which the MT7530 + switch is a part of the multi-chip module. reset-gpios: + description: + GPIO to reset the switch. Use this if mediatek,mcm is not used. + This property is optional because some boards share the reset line with + other components which makes it impossible to probe the switch if the + reset line is used. maxItems: 1 reset-names: @@ -110,8 +146,8 @@ properties: resets: description: - Phandle pointing to the system reset controller with line index for - the ethsys. + Phandle pointing to the system reset controller with line index for the + ethsys. maxItems: 1 patternProperties: @@ -128,31 +164,88 @@ patternProperties: properties: reg: description: - Port address described must be 5 or 6 for CPU port and from 0 - to 5 for user ports. + Port address described must be 5 or 6 for CPU port and from 0 to 5 + for user ports. allOf: - $ref: dsa-port.yaml# - if: - properties: - label: - items: - - const: cpu + required: [ ethernet ] then: - required: - - reg - - phy-mode + properties: + reg: + enum: + - 5 + - 6 required: - compatible - reg +$defs: + mt7530-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - gmii + - mii + - rgmii + else: + properties: + phy-mode: + enum: + - rgmii + - trgmii + + mt7531-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - rgmii + - sgmii + else: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - sgmii + allOf: - - $ref: "dsa.yaml#" + - $ref: dsa.yaml# - if: required: - mediatek,mcm then: + properties: + reset-gpios: false + required: - resets - reset-names @@ -163,52 +256,139 @@ allOf: - if: properties: compatible: - items: - - const: mediatek,mt7530 + const: mediatek,mt7530 then: + $ref: "#/$defs/mt7530-dsa-port" required: - core-supply - io-supply + - if: + properties: + compatible: + const: mediatek,mt7531 + then: + $ref: "#/$defs/mt7531-dsa-port" + properties: + gpio-controller: false + mediatek,mcm: false + + - if: + properties: + compatible: + const: mediatek,mt7621 + then: + $ref: "#/$defs/mt7530-dsa-port" + required: + - mediatek,mcm + unevaluatedProperties: false examples: + # Example 1: Standalone MT7530 - | #include <dt-bindings/gpio/gpio.h> + mdio { #address-cells = <1>; #size-cells = <0>; - switch@0 { + + switch@1f { compatible = "mediatek,mt7530"; - reg = <0>; + reg = <0x1f>; + + reset-gpios = <&pio 33 0>; core-supply = <&mt6323_vpa_reg>; io-supply = <&mt6323_vemc3v3_reg>; - reset-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; ethernet-ports { #address-cells = <1>; #size-cells = <0>; + port@0 { reg = <0>; - label = "lan0"; + label = "lan1"; }; port@1 { reg = <1>; - label = "lan1"; + label = "lan2"; }; port@2 { reg = <2>; - label = "lan2"; + label = "lan3"; }; port@3 { reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 2: MT7530 in MT7623AI SoC + - | + #include <dt-bindings/reset/mt2701-resets.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7530"; + reg = <0x1f>; + + mediatek,mcm; + resets = <ðsys MT2701_ETHSYS_MCM_RST>; + reset-names = "mcm"; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; label = "lan3"; }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { reg = <4>; label = "wan"; @@ -216,96 +396,226 @@ examples: port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac0>; phy-mode = "trgmii"; + fixed-link { speed = <1000>; full-duplex; + pause; }; }; }; }; }; + # Example 3: Standalone MT7531 - | - //Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> - ethernet { + mdio { #address-cells = <1>; #size-cells = <0>; - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; + + switch@0 { + compatible = "mediatek,mt7531"; reg = <0>; - phy-mode = "rgmii"; - fixed-link { - speed = <1000>; - full-duplex; - pause; + reset-gpios = <&pio 54 0>; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 4: MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; }; }; + }; - gmac1: mac@1 { + # Example 5: MT7621: mux MT7530's phy4 to SoC's gmac1 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { compatible = "mediatek,eth-mac"; reg = <1>; - phy-mode = "rgmii-txid"; - phy-handle = <&phy4>; + + phy-mode = "rgmii"; + phy-handle = <&example5_ethphy4>; }; - mdio: mdio-bus { + mdio { #address-cells = <1>; #size-cells = <0>; - /* Internal phy */ - phy4: ethernet-phy@4 { + /* MT7530's phy4 */ + example5_ethphy4: ethernet-phy@4 { reg = <4>; }; - mt7530: switch@1f { + switch@1f { compatible = "mediatek,mt7621"; reg = <0x1f>; - mediatek,mcm; - resets = <&rstctrl 2>; + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; reset-names = "mcm"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + ethernet-ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; - label = "lan0"; + label = "lan1"; }; port@1 { reg = <1>; - label = "lan1"; + label = "lan2"; }; port@2 { reg = <2>; - label = "lan2"; + label = "lan3"; }; port@3 { reg = <3>; - label = "lan3"; + label = "lan4"; }; - /* Commented out. Port 4 is handled by 2nd GMAC. + /* Commented out, phy4 is muxed to gmac1. port@4 { reg = <4>; - label = "lan4"; + label = "wan"; }; */ port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac0>; - phy-mode = "rgmii"; + phy-mode = "trgmii"; fixed-link { speed = <1000>; @@ -318,82 +628,169 @@ examples: }; }; + # Example 6: MT7621: mux external phy to SoC's gmac1 - | - //Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> ethernet { #address-cells = <1>; #size-cells = <0>; - gmac_0: mac@0 { + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { compatible = "mediatek,eth-mac"; - reg = <0>; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&example6_ethphy7>; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; - fixed-link { - speed = <1000>; - full-duplex; - pause; + /* External PHY */ + example6_ethphy7: ethernet-phy@7 { + reg = <7>; + phy-mode = "rgmii"; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; }; }; + }; + + # Example 7: MT7621: mux external phy to MT7530's port 5 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; - mdio0: mdio-bus { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mdio { #address-cells = <1>; #size-cells = <0>; - /* External phy */ - ephy5: ethernet-phy@7 { + /* External PHY */ + example7_ethphy7: ethernet-phy@7 { reg = <7>; + phy-mode = "rgmii"; }; switch@1f { compatible = "mediatek,mt7621"; reg = <0x1f>; - mediatek,mcm; - resets = <&rstctrl 2>; + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; reset-names = "mcm"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + ethernet-ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; - label = "lan0"; + label = "lan1"; }; port@1 { reg = <1>; - label = "lan1"; + label = "lan2"; }; port@2 { reg = <2>; - label = "lan2"; + label = "lan3"; }; port@3 { reg = <3>; - label = "lan3"; + label = "lan4"; }; port@4 { reg = <4>; - label = "lan4"; + label = "wan"; }; port@5 { reg = <5>; - label = "lan5"; - phy-mode = "rgmii"; - phy-handle = <&ephy5>; + label = "extphy"; + phy-mode = "rgmii-txid"; + phy-handle = <&example7_ethphy7>; }; - cpu_port0: port@6 { + port@6 { reg = <6>; - label = "cpu"; - ethernet = <&gmac_0>; - phy-mode = "rgmii"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; fixed-link { speed = <1000>; diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml index 6bbd8145b6c1..4da75b1f9533 100644 --- a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml +++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml @@ -107,8 +107,9 @@ examples: }; port@5 { reg = <5>; - label = "cpu"; ethernet = <ð0>; + phy-mode = "rgmii"; + fixed-link { speed = <1000>; full-duplex; @@ -144,8 +145,9 @@ examples: }; port@6 { reg = <6>; - label = "cpu"; ethernet = <ð0>; + phy-mode = "rgmii"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml new file mode 100644 index 000000000000..8d93ed9c172c --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml @@ -0,0 +1,260 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mscc,ocelot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Ocelot Switch Family Device Tree Bindings + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + - Claudiu Manoil <claudiu.manoil@nxp.com> + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - UNGLinuxDriver@microchip.com + +description: | + There are multiple switches which are either part of the Ocelot-1 family, or + derivatives of this architecture. These switches can be found embedded in + various SoCs and accessed using MMIO, or as discrete chips and accessed over + SPI or PCIe. The present DSA binding shall be used when the host controlling + them performs packet I/O primarily through an Ethernet port of the switch + (which is attached to an Ethernet port of the host), rather than through + Frame DMA or register-based I/O. + + VSC9953 (Seville): + + This is found in the NXP T1040, where it is a memory-mapped platform + device. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 8 and 9 + - phy-mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3, 4, 5, 6, 7 + + VSC9959 (Felix): + + This is found in the NXP LS1028A. It is a PCI device, part of the larger + enetc root complex. As a result, the ethernet-switch node is a sub-node of + the PCIe root complex node and its "reg" property conforms to the parent + node bindings, describing it as PF 5 of device 0, bus 0. + + If any external switch port is enabled, the enetc PF2 (enetc_port2) should + be enabled as well. This is because the internal MDIO bus (exposed through + EA BAR 0) used to access the MAC PCS registers truly belongs to the enetc + port 2 and not to Felix. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 4 and 5 + - phy-mode = "sgmii": on ports 0, 1, 2, 3 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3 + - phy-mode = "usxgmii": on ports 0, 1, 2, 3 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3 + - phy-mode = "2500base-x": on ports 0, 1, 2, 3 + +properties: + compatible: + enum: + - mscc,vsc9953-switch + - pci1957,eef0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + description: + Used to signal availability of PTP TX timestamps, and state changes of + the MAC merge layer of ports that support Frame Preemption. + + little-endian: true + big-endian: true + +required: + - compatible + - reg + +allOf: + - $ref: dsa.yaml# + - if: + properties: + compatible: + const: pci1957,eef0 + then: + required: + - interrupts + +unevaluatedProperties: false + +examples: + # Felix VSC9959 (NXP LS1028A) + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pcie { /* Integrated Endpoint Root Complex */ + #address-cells = <3>; + #size-cells = <2>; + + ethernet-switch@0,5 { + compatible = "pci1957,eef0"; + reg = <0x000500 0 0 0 0>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + ethernet = <&enetc_port2>; + phy-mode = "internal"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@5 { + reg = <5>; + ethernet = <&enetc_port3>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + # Seville VSC9953 (NXP T1040) + - | + soc { + #address-cells = <1>; + #size-cells = <1>; + + ethernet-switch@800000 { + compatible = "mscc,vsc9953-switch"; + reg = <0x800000 0x290000>; + little-endian; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + phy-mode = "qsgmii"; + phy-handle = <&phy4>; + managed = "in-band-status"; + }; + + port@5 { + reg = <5>; + phy-mode = "qsgmii"; + phy-handle = <&phy5>; + managed = "in-band-status"; + }; + + port@6 { + reg = <6>; + phy-mode = "qsgmii"; + phy-handle = <&phy6>; + managed = "in-band-status"; + }; + + port@7 { + reg = <7>; + phy-mode = "qsgmii"; + phy-handle = <&phy7>; + managed = "in-band-status"; + }; + + port@8 { + reg = <8>; + phy-mode = "internal"; + ethernet = <&enet0>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@9 { + reg = <9>; + phy-mode = "internal"; + ethernet = <&enet1>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt deleted file mode 100644 index 7a271d070b72..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/ocelot.txt +++ /dev/null @@ -1,213 +0,0 @@ -Microchip Ocelot switch driver family -===================================== - -Felix ------ - -Currently the switches supported by the felix driver are: - -- VSC9959 (Felix) -- VSC9953 (Seville) - -The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the -larger ENETC root complex. As a result, the ethernet-switch node is a sub-node -of the PCIe root complex node and its "reg" property conforms to the parent -node bindings: - -* reg: Specifies PCIe Device Number and Function Number of the endpoint device, - in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0). - -It does not require a "compatible" string. - -The interrupt line is used to signal availability of PTP TX timestamps and for -TSN frame preemption. - -For the external switch ports, depending on board configuration, "phy-mode" and -"phy-handle" are populated by board specific device tree instances. Ports 4 and -5 are fixed as internal ports in the NXP LS1028A instantiation. - -The CPU port property ("ethernet") configures the feature called "NPI port" in -the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are -connected, in the Node Processor Interface (NPI) mode, to an Ethernet port. -By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal -2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific -use case. Moving the NPI port to an external switch port is hardware possible, -but there is no platform support for the Linux system on the LS1028A chip to -operate as an entire slave DSA chip. NPI functionality (and therefore DSA -tagging) is supported on a single port at a time. - -Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled -by default, and should be enabled on a per-board basis). But if any external -switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as -well, regardless of whether it is configured as the DSA master or not. This is -because the Felix PHYLINK implementation accesses the MAC PCS registers, which -in hardware truly belong to the ENETC port #2 and not to Felix. - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 4 and 5 -* phy_mode = "sgmii": on ports 0, 1, 2, 3 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3 -* phy_mode = "usxgmii": on ports 0, 1, 2, 3 -* phy_mode = "2500base-x": on ports 0, 1, 2, 3 - -For the rest of the device tree binding definitions, which are standard DSA and -PCI, refer to the following documents: - -Documentation/devicetree/bindings/net/dsa/dsa.txt -Documentation/devicetree/bindings/pci/pci.txt - -Example: - -&soc { - pcie@1f0000000 { /* Integrated Endpoint Root Complex */ - ethernet-switch@0,5 { - reg = <0x000500 0 0 0 0>; - /* IEP INT_B */ - interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - /* External ports */ - port@0 { - reg = <0>; - label = "swp0"; - }; - - port@1 { - reg = <1>; - label = "swp1"; - }; - - port@2 { - reg = <2>; - label = "swp2"; - }; - - port@3 { - reg = <3>; - label = "swp3"; - }; - - /* Tagging CPU port */ - port@4 { - reg = <4>; - ethernet = <&enetc_port2>; - phy-mode = "internal"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - /* Non-tagging CPU port */ - port@5 { - reg = <5>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; -}; - -The VSC9953 switch is found inside NXP T1040. It is a platform device with the -following required properties: - -- compatible: - Must be "mscc,vsc9953-switch". - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 8 and 9 -* phy_mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 - -Example: - -&soc { - ethernet-switch@800000 { - #address-cells = <0x1>; - #size-cells = <0x0>; - compatible = "mscc,vsc9953-switch"; - little-endian; - reg = <0x800000 0x290000>; - - ports { - #address-cells = <0x1>; - #size-cells = <0x0>; - - port@0 { - reg = <0x0>; - label = "swp0"; - }; - - port@1 { - reg = <0x1>; - label = "swp1"; - }; - - port@2 { - reg = <0x2>; - label = "swp2"; - }; - - port@3 { - reg = <0x3>; - label = "swp3"; - }; - - port@4 { - reg = <0x4>; - label = "swp4"; - }; - - port@5 { - reg = <0x5>; - label = "swp5"; - }; - - port@6 { - reg = <0x6>; - label = "swp6"; - }; - - port@7 { - reg = <0x7>; - label = "swp7"; - }; - - port@8 { - reg = <0x8>; - phy-mode = "internal"; - ethernet = <&enet0>; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - port@9 { - reg = <0x9>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml index f3c88371d76c..978162df51f7 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml @@ -159,7 +159,6 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; @@ -221,7 +220,6 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; @@ -268,7 +266,6 @@ examples: port@6 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "sgmii"; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml index 4f99aff029dc..1a7d45a8ad66 100644 --- a/Documentation/devicetree/bindings/net/dsa/realtek.yaml +++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml @@ -189,7 +189,6 @@ examples: }; port@5 { reg = <5>; - label = "cpu"; ethernet = <&gmac0>; phy-mode = "rgmii"; fixed-link { @@ -277,7 +276,6 @@ examples: }; port@6 { reg = <6>; - label = "cpu"; ethernet = <&fec1>; phy-mode = "rgmii"; tx-internal-delay-ps = <2000>; diff --git a/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml index 4d428f5ad044..7ca9c19a157c 100644 --- a/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml +++ b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml @@ -130,7 +130,8 @@ examples: port@4 { reg = <4>; ethernet = <&gmac2>; - label = "cpu"; + phy-mode = "internal"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt index bbf4a13f6d75..258bef483673 100644 --- a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt +++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt @@ -75,7 +75,6 @@ switch@0 { }; vsc: port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; fixed-link { @@ -117,7 +116,6 @@ switch@2,0 { }; vsc: port@6 { reg = <6>; - label = "cpu"; ethernet = <&enet0>; phy-mode = "rgmii"; fixed-link { diff --git a/Documentation/devicetree/bindings/net/engleder,tsnep.yaml b/Documentation/devicetree/bindings/net/engleder,tsnep.yaml index d0e1476e15b5..5bd964a46a9d 100644 --- a/Documentation/devicetree/bindings/net/engleder,tsnep.yaml +++ b/Documentation/devicetree/bindings/net/engleder,tsnep.yaml @@ -20,7 +20,26 @@ properties: maxItems: 1 interrupts: - maxItems: 1 + minItems: 1 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: mac + - const: txrx-1 + - const: txrx-2 + - const: txrx-3 + - const: txrx-4 + - const: txrx-5 + - const: txrx-6 + - const: txrx-7 + description: + The main interrupt for basic MAC features and the first TX/RX queue pair + is named "mac". "txrx-[1-7]" are the interrupts for additional TX/RX + queue pairs. + + dma-coherent: true local-mac-address: true @@ -58,7 +77,7 @@ examples: axi { #address-cells = <2>; #size-cells = <2>; - tnsep0: ethernet@a0000000 { + tsnep0: ethernet@a0000000 { compatible = "engleder,tsnep"; reg = <0x0 0xa0000000 0x0 0x10000>; interrupts = <0 89 1>; @@ -76,4 +95,24 @@ examples: }; }; }; + + tsnep1: ethernet@a0010000 { + compatible = "engleder,tsnep"; + reg = <0x0 0xa0010000 0x0 0x10000>; + interrupts = <0 93 1>, <0 94 1>, <0 95 1>, <0 96 1>; + interrupt-names = "mac", "txrx-1", "txrx-2", "txrx-3"; + interrupt-parent = <&gic>; + local-mac-address = [00 00 00 00 00 00]; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + suppress-preamble; + phy1: ethernet-phy@1 { + reg = <1>; + rxc-skew-ps = <1080>; + }; + }; + }; }; diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml index c138a1022879..4b3c590fcebf 100644 --- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml @@ -67,6 +67,7 @@ properties: - gmii - sgmii - qsgmii + - qusgmii - tbi - rev-mii - rmii diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml index ed1415a4381f..ad808e9ce5b9 100644 --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml @@ -144,6 +144,12 @@ properties: Mark the corresponding energy efficient ethernet mode as broken and request the ethernet to stop advertising it. + pses: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: + Specifies a reference to a node representing a Power Sourcing Equipment. + phy-is-integrated: $ref: /schemas/types.yaml#/definitions/flag description: diff --git a/Documentation/devicetree/bindings/net/fsl,fec.yaml b/Documentation/devicetree/bindings/net/fsl,fec.yaml index 5cfb661be124..e0f376f7e274 100644 --- a/Documentation/devicetree/bindings/net/fsl,fec.yaml +++ b/Documentation/devicetree/bindings/net/fsl,fec.yaml @@ -21,6 +21,7 @@ properties: - fsl,imx28-fec - fsl,imx6q-fec - fsl,mvf600-fec + - fsl,s32v234-fec - items: - enum: - fsl,imx53-fec diff --git a/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml b/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml new file mode 100644 index 000000000000..3a35ac1c260d --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml @@ -0,0 +1,145 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/fsl,fman-dtsec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP FMan MAC + +maintainers: + - Madalin Bucur <madalin.bucur@nxp.com> + +description: | + Each FMan has several MACs, each implementing an Ethernet interface. Earlier + versions of FMan used the Datapath Three Speed Ethernet Controller (dTSEC) for + 10/100/1000 MBit/s speeds, and the 10-Gigabit Ethernet Media Access Controller + (10GEC) for 10 Gbit/s speeds. Later versions of FMan use the Multirate + Ethernet Media Access Controller (mEMAC) to handle all speeds. + +properties: + compatible: + enum: + - fsl,fman-dtsec + - fsl,fman-xgec + - fsl,fman-memac + + cell-index: + maximum: 64 + description: | + FManV2: + register[bit] MAC cell-index + ============================================================ + FM_EPI[16] XGEC 8 + FM_EPI[16+n] dTSECn n-1 + FM_NPI[11+n] dTSECn n-1 + n = 1,..,5 + + FManV3: + register[bit] MAC cell-index + ============================================================ + FM_EPI[16+n] mEMACn n-1 + FM_EPI[25] mEMAC10 9 + + FM_NPI[11+n] mEMACn n-1 + FM_NPI[10] mEMAC10 9 + FM_NPI[11] mEMAC9 8 + n = 1,..8 + + FM_EPI and FM_NPI are located in the FMan memory map. + + 2. SoC registers: + + - P2041, P3041, P4080 P5020, P5040: + register[bit] FMan MAC cell + Unit index + ============================================================ + DCFG_DEVDISR2[7] 1 XGEC 8 + DCFG_DEVDISR2[7+n] 1 dTSECn n-1 + DCFG_DEVDISR2[15] 2 XGEC 8 + DCFG_DEVDISR2[15+n] 2 dTSECn n-1 + n = 1,..5 + + - T1040, T2080, T4240, B4860: + register[bit] FMan MAC cell + Unit index + ============================================================ + DCFG_CCSR_DEVDISR2[n-1] 1 mEMACn n-1 + DCFG_CCSR_DEVDISR2[11+n] 2 mEMACn n-1 + n = 1,..6,9,10 + + EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in + the specific SoC "Device Configuration/Pin Control" Memory + Map. + + reg: + maxItems: 1 + + fsl,fman-ports: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 2 + description: | + An array of two references: the first is the FMan RX port and the second + is the TX port used by this MAC. + + ptp-timer: + $ref: /schemas/types.yaml#/definitions/phandle + description: A reference to the IEEE1588 timer + + pcsphy-handle: + $ref: /schemas/types.yaml#/definitions/phandle + description: A reference to the PCS (typically found on the SerDes) + + tbi-handle: + $ref: /schemas/types.yaml#/definitions/phandle + description: A reference to the (TBI-based) PCS + +required: + - compatible + - cell-index + - reg + - fsl,fman-ports + - ptp-timer + +allOf: + - $ref: ethernet-controller.yaml# + - if: + properties: + compatible: + contains: + const: fsl,fman-dtsec + then: + required: + - tbi-handle + - if: + properties: + compatible: + contains: + const: fsl,fman-memac + then: + required: + - pcsphy-handle + +unevaluatedProperties: false + +examples: + - | + ethernet@e0000 { + compatible = "fsl,fman-dtsec"; + cell-index = <0>; + reg = <0xe0000 0x1000>; + fsl,fman-ports = <&fman1_rx8 &fman1_tx28>; + ptp-timer = <&ptp_timer>; + tbi-handle = <&tbi0>; + }; + - | + ethernet@e8000 { + cell-index = <4>; + compatible = "fsl,fman-memac"; + reg = <0xe8000 0x1000>; + fsl,fman-ports = <&fman0_rx_0x0c &fman0_tx_0x2c>; + ptp-timer = <&ptp_timer0>; + pcsphy-handle = <&pcsphy4>; + phy-handle = <&sgmii_phy1>; + phy-connection-type = "sgmii"; + }; +... diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt index 801efc7d6818..b9055335db3b 100644 --- a/Documentation/devicetree/bindings/net/fsl-fman.txt +++ b/Documentation/devicetree/bindings/net/fsl-fman.txt @@ -232,133 +232,7 @@ port@81000 { ============================================================================= FMan dTSEC/XGEC/mEMAC Node -DESCRIPTION - -mEMAC/dTSEC/XGEC are the Ethernet network interfaces - -PROPERTIES - -- compatible - Usage: required - Value type: <stringlist> - Definition: A standard property. - Must include one of the following: - - "fsl,fman-dtsec" for dTSEC MAC - - "fsl,fman-xgec" for XGEC MAC - - "fsl,fman-memac" for mEMAC MAC - -- cell-index - Usage: required - Value type: <u32> - Definition: Specifies the MAC id. - - The cell-index value may be used by the FMan or the SoC, to - identify the MAC unit in the FMan (or SoC) memory map. - In the tables below there's a description of the cell-index - use, there are two tables, one describes the use of cell-index - by the FMan, the second describes the use by the SoC: - - 1. FMan Registers - - FManV2: - register[bit] MAC cell-index - ============================================================ - FM_EPI[16] XGEC 8 - FM_EPI[16+n] dTSECn n-1 - FM_NPI[11+n] dTSECn n-1 - n = 1,..,5 - - FManV3: - register[bit] MAC cell-index - ============================================================ - FM_EPI[16+n] mEMACn n-1 - FM_EPI[25] mEMAC10 9 - - FM_NPI[11+n] mEMACn n-1 - FM_NPI[10] mEMAC10 9 - FM_NPI[11] mEMAC9 8 - n = 1,..8 - - FM_EPI and FM_NPI are located in the FMan memory map. - - 2. SoC registers: - - - P2041, P3041, P4080 P5020, P5040: - register[bit] FMan MAC cell - Unit index - ============================================================ - DCFG_DEVDISR2[7] 1 XGEC 8 - DCFG_DEVDISR2[7+n] 1 dTSECn n-1 - DCFG_DEVDISR2[15] 2 XGEC 8 - DCFG_DEVDISR2[15+n] 2 dTSECn n-1 - n = 1,..5 - - - T1040, T2080, T4240, B4860: - register[bit] FMan MAC cell - Unit index - ============================================================ - DCFG_CCSR_DEVDISR2[n-1] 1 mEMACn n-1 - DCFG_CCSR_DEVDISR2[11+n] 2 mEMACn n-1 - n = 1,..6,9,10 - - EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in - the specific SoC "Device Configuration/Pin Control" Memory - Map. - -- reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. - -- fsl,fman-ports - Usage: required - Value type: <prop-encoded-array> - Definition: An array of two phandles - the first references is - the FMan RX port and the second is the TX port used by this - MAC. - -- ptp-timer - Usage required - Value type: <phandle> - Definition: A phandle for 1EEE1588 timer. - -- pcsphy-handle - Usage required for "fsl,fman-memac" MACs - Value type: <phandle> - Definition: A phandle for pcsphy. - -- tbi-handle - Usage required for "fsl,fman-dtsec" MACs - Value type: <phandle> - Definition: A phandle for tbiphy. - -EXAMPLE - -fman1_tx28: port@a8000 { - cell-index = <0x28>; - compatible = "fsl,fman-v2-port-tx"; - reg = <0xa8000 0x1000>; -}; - -fman1_rx8: port@88000 { - cell-index = <0x8>; - compatible = "fsl,fman-v2-port-rx"; - reg = <0x88000 0x1000>; -}; - -ptp-timer: ptp_timer@fe000 { - compatible = "fsl,fman-ptp-timer"; - reg = <0xfe000 0x1000>; -}; - -ethernet@e0000 { - compatible = "fsl,fman-dtsec"; - cell-index = <0>; - reg = <0xe0000 0x1000>; - fsl,fman-ports = <&fman1_rx8 &fman1_tx28>; - ptp-timer = <&ptp-timer>; - tbi-handle = <&tbi0>; -}; +Refer to Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml ============================================================================ FMan IEEE 1588 Node diff --git a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt deleted file mode 100644 index 358fed2fab43..000000000000 --- a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt +++ /dev/null @@ -1,24 +0,0 @@ -Mediatek Gigabit Switch -======================= - -The mediatek gigabit switch can be found on Mediatek SoCs (mt7620, mt7621). - -Required properties: -- compatible: Should be "mediatek,mt7620-gsw" or "mediatek,mt7621-gsw" -- reg: Address and length of the register set for the device -- interrupts: Should contain the gigabit switches interrupt -- resets: Should contain the gigabit switches resets -- reset-names: Should contain the reset names "gsw" - -Example: - -gsw@10110000 { - compatible = "ralink,mt7620-gsw"; - reg = <0x10110000 8000>; - - resets = <&rstctrl 23>; - reset-names = "gsw"; - - interrupt-parent = <&intc>; - interrupts = <17>; -}; diff --git a/Documentation/devicetree/bindings/net/mediatek,net.yaml b/Documentation/devicetree/bindings/net/mediatek,net.yaml index f5564ecddb62..7ef696204c5a 100644 --- a/Documentation/devicetree/bindings/net/mediatek,net.yaml +++ b/Documentation/devicetree/bindings/net/mediatek,net.yaml @@ -69,6 +69,15 @@ properties: A list of phandle to the syscon node that handles the SGMII setup which is required for those SoCs equipped with SGMII. + mediatek,wed: + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 2 + maxItems: 2 + items: + maxItems: 1 + description: + List of phandles to wireless ethernet dispatch nodes. + dma-coherent: true mdio-bus: @@ -112,6 +121,8 @@ allOf: Phandle to the syscon node that handles the ports slew rate and driver current. + mediatek,wed: false + - if: properties: compatible: @@ -144,15 +155,6 @@ allOf: minItems: 1 maxItems: 1 - mediatek,wed: - $ref: /schemas/types.yaml#/definitions/phandle-array - minItems: 2 - maxItems: 2 - items: - maxItems: 1 - description: - List of phandles to wireless ethernet dispatch nodes. - mediatek,pcie-mirror: $ref: /schemas/types.yaml#/definitions/phandle description: @@ -202,6 +204,8 @@ allOf: minItems: 2 maxItems: 2 + mediatek,wed: false + - if: properties: compatible: @@ -238,6 +242,11 @@ allOf: minItems: 2 maxItems: 2 + mediatek,wed-pcie: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the mediatek wed-pcie controller. + patternProperties: "^mac@[0-1]$": type: object diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml index 61b2fb9e141b..0fa2132fa4f4 100644 --- a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml @@ -19,6 +19,7 @@ select: contains: enum: - mediatek,mt2712-gmac + - mediatek,mt8188-gmac - mediatek,mt8195-gmac required: - compatible @@ -37,6 +38,11 @@ properties: - enum: - mediatek,mt8195-gmac - const: snps,dwmac-5.10a + - items: + - enum: + - mediatek,mt8188-gmac + - const: mediatek,mt8195-gmac + - const: snps,dwmac-5.10a clocks: minItems: 5 @@ -74,7 +80,7 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. - For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, + For MT8188/MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, or will round down. Range 0~31*290. mediatek,rx-delay-ps: @@ -84,7 +90,7 @@ properties: or will round down. Range 0~31*170. For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550, or will round down. Range 0~31*550. - For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple + For MT8188/MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, or will round down. Range 0~31*290. mediatek,rmii-rxc: diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml index 6c86d3d85e99..57ffeb8fc876 100644 --- a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml +++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml @@ -74,16 +74,20 @@ properties: ethernet-ports: type: object + additionalProperties: false + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + patternProperties: "^port@[0-9a-f]+$": - type: object + $ref: /schemas/net/ethernet-controller.yaml# + unevaluatedProperties: false properties: - '#address-cells': - const: 1 - '#size-cells': - const: 0 - reg: description: Switch port number @@ -93,29 +97,11 @@ properties: phandle of a Ethernet SerDes PHY. This defines which SerDes instance will handle the Ethernet traffic. - phy-mode: - description: - This specifies the interface used by the Ethernet SerDes towards - the PHY or SFP. - microchip,bandwidth: description: Specifies bandwidth in Mbit/s allocated to the port. $ref: "/schemas/types.yaml#/definitions/uint32" maximum: 25000 - phy-handle: - description: - phandle of a Ethernet PHY. This is optional and if provided it - points to the cuPHY used by the Ethernet SerDes. - - sfp: - description: - phandle of an SFP. This is optional and used when not specifying - a cuPHY. It points to the SFP node that describes the SFP used by - the Ethernet SerDes. - - managed: true - microchip,sd-sgpio: description: Index of the ports Signal Detect SGPIO in the set of 384 SGPIOs @@ -144,8 +130,6 @@ required: - reg-names - interrupts - interrupt-names - - resets - - reset-names - ethernet-ports additionalProperties: false diff --git a/Documentation/devicetree/bindings/net/nfc/marvell,nci.yaml b/Documentation/devicetree/bindings/net/nfc/marvell,nci.yaml index a191a04e681c..308485a8ee6c 100644 --- a/Documentation/devicetree/bindings/net/nfc/marvell,nci.yaml +++ b/Documentation/devicetree/bindings/net/nfc/marvell,nci.yaml @@ -128,7 +128,7 @@ examples: i2c-int-rising; - reset-n-io = <&gpio3 19 GPIO_ACTIVE_HIGH>; + reset-n-io = <&gpio3 19 GPIO_ACTIVE_LOW>; }; }; @@ -151,7 +151,7 @@ examples: interrupt-parent = <&gpio1>; interrupts = <17 IRQ_TYPE_EDGE_RISING>; - reset-n-io = <&gpio3 19 GPIO_ACTIVE_HIGH>; + reset-n-io = <&gpio3 19 GPIO_ACTIVE_LOW>; }; }; @@ -162,7 +162,7 @@ examples: nfc { compatible = "marvell,nfc-uart"; - reset-n-io = <&gpio3 16 GPIO_ACTIVE_HIGH>; + reset-n-io = <&gpio3 16 GPIO_ACTIVE_LOW>; hci-muxed; flow-control; diff --git a/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml b/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml index d51da24f3505..ab8867e6939b 100644 --- a/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml +++ b/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml @@ -31,6 +31,22 @@ patternProperties: description: The ID number for the child PHY. Should be +1 of parent PHY. + nxp,rmii-refclk-in: + type: boolean + description: | + The REF_CLK is provided for both transmitted and received data + in RMII mode. This clock signal is provided by the PHY and is + typically derived from an external 25MHz crystal. Alternatively, + a 50MHz clock signal generated by an external oscillator can be + connected to pin REF_CLK. A third option is to connect a 25MHz + clock to pin CLK_IN_OUT. So, the REF_CLK should be configured + as input or output according to the actual circuit connection. + If present, indicates that the REF_CLK will be configured as + interface reference clock input when RMII mode enabled. + If not present, the REF_CLK will be configured as interface + reference clock output when RMII mode enabled. + Only supported on TJA1100 and TJA1101. + required: - reg @@ -44,6 +60,7 @@ examples: tja1101_phy0: ethernet-phy@4 { reg = <0x4>; + nxp,rmii-refclk-in; }; }; - | diff --git a/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml b/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml new file mode 100644 index 000000000000..c6b1c188abf7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/pse-pd/podl-pse-regulator.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/pse-pd/podl-pse-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Regulator based Power Sourcing Equipment + +maintainers: + - Oleksij Rempel <o.rempel@pengutronix.de> + +description: Regulator based PoDL PSE controller. The device must be referenced + by the PHY node to control power injection to the Ethernet cable. + +allOf: + - $ref: "pse-controller.yaml#" + +properties: + compatible: + const: podl-pse-regulator + + '#pse-cells': + const: 0 + + pse-supply: + description: Power supply for the PSE controller + +additionalProperties: false + +required: + - compatible + - pse-supply + +examples: + - | + ethernet-pse { + compatible = "podl-pse-regulator"; + pse-supply = <®_t1l1>; + #pse-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/net/pse-pd/pse-controller.yaml b/Documentation/devicetree/bindings/net/pse-pd/pse-controller.yaml new file mode 100644 index 000000000000..b110abb42597 --- /dev/null +++ b/Documentation/devicetree/bindings/net/pse-pd/pse-controller.yaml @@ -0,0 +1,33 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/pse-pd/pse-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Power Sourcing Equipment (PSE). + +description: Binding for the Power Sourcing Equipment (PSE) as defined in the + IEEE 802.3 specification. It is designed for hardware which is delivering + power over twisted pair/ethernet cable. The ethernet-pse nodes should be + used to describe PSE controller and referenced by the ethernet-phy node. + +maintainers: + - Oleksij Rempel <o.rempel@pengutronix.de> + +properties: + $nodename: + pattern: "^ethernet-pse(@.*)?$" + + "#pse-cells": + description: + Used to uniquely identify a PSE instance within an IC. Will be + 0 on PSE nodes with only a single output and at least 1 on nodes + controlling several outputs. + enum: [0, 1] + +required: + - "#pse-cells" + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/net/qca,ar803x.yaml b/Documentation/devicetree/bindings/net/qca,ar803x.yaml index b3d4013b7ca6..161d28919316 100644 --- a/Documentation/devicetree/bindings/net/qca,ar803x.yaml +++ b/Documentation/devicetree/bindings/net/qca,ar803x.yaml @@ -40,6 +40,14 @@ properties: Only supported on the AR8031. type: boolean + qca,disable-hibernation-mode: + description: | + Disable Atheros AR803X PHYs hibernation mode. If present, indicates + that the hardware of PHY will not enter power saving mode when the + cable is disconnected. And the RX_CLK always keeps outputting a + valid clock. + type: boolean + qca,smarteee-tw-us-100m: description: EEE Tw parameter for 100M links. $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt deleted file mode 100644 index 9fe1a0a22e44..000000000000 --- a/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt +++ /dev/null @@ -1,59 +0,0 @@ -Ralink Frame Engine Ethernet controller -======================================= - -The Ralink frame engine ethernet controller can be found on Ralink and -Mediatek SoCs (RT288x, RT3x5x, RT366x, RT388x, rt5350, mt7620, mt7621, mt76x8). - -Depending on the SoC, there is a number of ports connected to the CPU port -directly and/or via a (gigabit-)switch. - -* Ethernet controller node - -Required properties: -- compatible: Should be one of "ralink,rt2880-eth", "ralink,rt3050-eth", - "ralink,rt3050-eth", "ralink,rt3883-eth", "ralink,rt5350-eth", - "mediatek,mt7620-eth", "mediatek,mt7621-eth" -- reg: Address and length of the register set for the device -- interrupts: Should contain the frame engines interrupt -- resets: Should contain the frame engines resets -- reset-names: Should contain the reset names "fe". If a switch is present - "esw" is also required. - - -* Ethernet port node - -Required properties: -- compatible: Should be "ralink,eth-port" -- reg: The number of the physical port -- phy-handle: reference to the node describing the phy - -Example: - -mdio-bus { - ... - phy0: ethernet-phy@0 { - phy-mode = "mii"; - reg = <0>; - }; -}; - -ethernet@400000 { - compatible = "ralink,rt2880-eth"; - reg = <0x00400000 10000>; - - #address-cells = <1>; - #size-cells = <0>; - - resets = <&rstctrl 18>; - reset-names = "fe"; - - interrupt-parent = <&cpuintc>; - interrupts = <5>; - - port@0 { - compatible = "ralink,eth-port"; - reg = <0>; - phy-handle = <&phy0>; - }; - -}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt deleted file mode 100644 index 87e315856efa..000000000000 --- a/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt +++ /dev/null @@ -1,30 +0,0 @@ -Ralink Fast Ethernet Embedded Switch -==================================== - -The ralink fast ethernet embedded switch can be found on Ralink and Mediatek -SoCs (RT3x5x, RT5350, MT76x8). - -Required properties: -- compatible: Should be "ralink,rt3050-esw" -- reg: Address and length of the register set for the device -- interrupts: Should contain the embedded switches interrupt -- resets: Should contain the embedded switches resets -- reset-names: Should contain the reset names "esw" - -Optional properties: -- ralink,portmap: can be used to choose if the default switch setup is - llllw or wllll -- ralink,led_polarity: override the active high/low settings of the leds - -Example: - -esw@10110000 { - compatible = "ralink,rt3050-esw"; - reg = <0x10110000 8000>; - - resets = <&rstctrl 23>; - reset-names = "esw"; - - interrupt-parent = <&intc>; - interrupts = <17>; -}; diff --git a/Documentation/devicetree/bindings/net/renesas,etheravb.yaml b/Documentation/devicetree/bindings/net/renesas,etheravb.yaml index acf347f3cdbe..3f41294f5997 100644 --- a/Documentation/devicetree/bindings/net/renesas,etheravb.yaml +++ b/Documentation/devicetree/bindings/net/renesas,etheravb.yaml @@ -40,11 +40,16 @@ properties: - renesas,etheravb-r8a77980 # R-Car V3H - renesas,etheravb-r8a77990 # R-Car E3 - renesas,etheravb-r8a77995 # R-Car D3 - - renesas,etheravb-r8a779a0 # R-Car V3U - const: renesas,etheravb-rcar-gen3 # R-Car Gen3 and RZ/G2 - items: - enum: + - renesas,etheravb-r8a779a0 # R-Car V3U + - renesas,etheravb-r8a779g0 # R-Car V4H + - const: renesas,etheravb-rcar-gen4 # R-Car Gen4 + + - items: + - enum: - renesas,etheravb-r9a09g011 # RZ/V2M - const: renesas,etheravb-rzv2m # RZ/V2M compatible @@ -207,7 +212,7 @@ allOf: - renesas,etheravb-r8a77965 - renesas,etheravb-r8a77970 - renesas,etheravb-r8a77980 - - renesas,etheravb-r8a779a0 + - renesas,etheravb-rcar-gen4 then: required: - tx-internal-delay-ps diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml b/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml index 083623c8d718..42fb72b6909d 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml @@ -25,7 +25,9 @@ select: - rockchip,rk3368-gmac - rockchip,rk3399-gmac - rockchip,rk3568-gmac + - rockchip,rk3588-gmac - rockchip,rv1108-gmac + - rockchip,rv1126-gmac required: - compatible @@ -47,9 +49,11 @@ properties: - rockchip,rk3368-gmac - rockchip,rk3399-gmac - rockchip,rv1108-gmac + - rockchip,rv1126-gmac - items: - enum: - rockchip,rk3568-gmac + - rockchip,rk3588-gmac - const: snps,dwmac-4.20a clocks: @@ -81,6 +85,11 @@ properties: description: The phandle of the syscon node for the general register file. $ref: /schemas/types.yaml#/definitions/phandle + rockchip,php-grf: + description: + The phandle of the syscon node for the peripheral general register file. + $ref: /schemas/types.yaml#/definitions/phandle + tx_delay: description: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default. $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/net/snps,dwmac.yaml b/Documentation/devicetree/bindings/net/snps,dwmac.yaml index 491597c02edf..f94a0a4320f1 100644 --- a/Documentation/devicetree/bindings/net/snps,dwmac.yaml +++ b/Documentation/devicetree/bindings/net/snps,dwmac.yaml @@ -74,6 +74,7 @@ properties: - rockchip,rk3328-gmac - rockchip,rk3366-gmac - rockchip,rk3368-gmac + - rockchip,rk3588-gmac - rockchip,rk3399-gmac - rockchip,rv1108-gmac - snps,dwmac @@ -288,6 +289,11 @@ properties: is supported. For example, this is used in case of SGMII and MAC2MAC connection. + snps,clk-csr: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Frequency division factor for MDC clock. + mdio: $ref: mdio.yaml# unevaluatedProperties: false @@ -301,6 +307,60 @@ properties: required: - compatible + stmmac-axi-config: + type: object + unevaluatedProperties: false + description: + AXI BUS Mode parameters. + + properties: + snps,lpi_en: + $ref: /schemas/types.yaml#/definitions/flag + description: + enable Low Power Interface + + snps,xit_frm: + $ref: /schemas/types.yaml#/definitions/flag + description: + unlock on WoL + + snps,wr_osr_lmt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + max write outstanding req. limit + + snps,rd_osr_lmt: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + max read outstanding req. limit + + snps,kbbe: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + do not cross 1KiB boundary. + + snps,blen: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + this is a vector of supported burst length. + minItems: 7 + maxItems: 7 + + snps,fb: + $ref: /schemas/types.yaml#/definitions/flag + description: + fixed-burst + + snps,mb: + $ref: /schemas/types.yaml#/definitions/flag + description: + mixed-burst + + snps,rb: + $ref: /schemas/types.yaml#/definitions/flag + description: + rebuild INCRx Burst + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/sunplus,sp7021-emac.yaml b/Documentation/devicetree/bindings/net/sunplus,sp7021-emac.yaml index 62dffee27c3d..8e51dcdb4796 100644 --- a/Documentation/devicetree/bindings/net/sunplus,sp7021-emac.yaml +++ b/Documentation/devicetree/bindings/net/sunplus,sp7021-emac.yaml @@ -32,6 +32,7 @@ properties: ethernet-ports: type: object + additionalProperties: false description: Ethernet ports to PHY properties: @@ -44,6 +45,7 @@ properties: patternProperties: "^port@[0-1]$": type: object + additionalProperties: false description: Port to PHY properties: diff --git a/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml b/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml index 31bf825c6598..46e330f45768 100644 --- a/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml +++ b/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml @@ -77,6 +77,8 @@ properties: ethernet-ports: type: object + additionalProperties: false + properties: '#address-cells': const: 1 @@ -89,6 +91,7 @@ properties: description: CPSW external ports $ref: ethernet-controller.yaml# + unevaluatedProperties: false properties: reg: @@ -117,6 +120,7 @@ properties: cpts: type: object + unevaluatedProperties: false description: The Common Platform Time Sync (CPTS) module diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml index b8281d8be940..7d90beaccc60 100644 --- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml +++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml @@ -55,6 +55,7 @@ properties: compatible: enum: - ti,am654-cpsw-nuss + - ti,j7200-cpswxg-nuss - ti,j721e-cpsw-nuss - ti,am642-cpsw-nuss @@ -110,16 +111,17 @@ properties: const: 0 patternProperties: - port@[1-2]: + "^port@[1-4]$": type: object description: CPSWxG NUSS external ports $ref: ethernet-controller.yaml# + unevaluatedProperties: false properties: reg: minimum: 1 - maximum: 2 + maximum: 4 description: CPSW port number phys: @@ -178,6 +180,19 @@ required: - '#address-cells' - '#size-cells' +allOf: + - if: + not: + properties: + compatible: + contains: + const: ti,j7200-cpswxg-nuss + then: + properties: + ethernet-ports: + patternProperties: + "^port@[3-4]$": false + additionalProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml index b783ad0d1f53..e9f78cef6b7f 100644 --- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml +++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml @@ -95,6 +95,7 @@ properties: refclk-mux: type: object + additionalProperties: false description: CPTS reference clock multiplexer clock properties: '#clock-cells': diff --git a/Documentation/devicetree/bindings/net/vertexcom-mse102x.yaml b/Documentation/devicetree/bindings/net/vertexcom-mse102x.yaml index 8156a9aeb589..304757bf9281 100644 --- a/Documentation/devicetree/bindings/net/vertexcom-mse102x.yaml +++ b/Documentation/devicetree/bindings/net/vertexcom-mse102x.yaml @@ -7,7 +7,7 @@ $schema: "http://devicetree.org/meta-schemas/core.yaml#" title: The Vertexcom MSE102x (SPI) Device Tree Bindings maintainers: - - Stefan Wahren <stefan.wahren@in-tech.com> + - Stefan Wahren <stefan.wahren@chargebyte.com> description: Vertexcom's MSE102x are a family of HomePlug GreenPHY chips. diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml index 53b4153d9bfc..fec1cc9b9a08 100644 --- a/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <arend@broadcom.com> @@ -41,11 +41,17 @@ properties: - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1 @@ -85,6 +91,31 @@ properties: takes precedence. type: boolean + brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present. + + brcm,board-type: + $ref: /schemas/types.yaml#/definitions/string + description: Overrides the board type, which is normally the compatible of + the root node. This can be used to decouple the overall system board or + device name from the board type for WiFi purposes, which is used to + construct firmware and NVRAM configuration filenames, allowing for + multiple devices that share the same module or characteristics for the + WiFi subsystem to share the same firmware/NVRAM files. On Apple platforms, + this should be the Apple module-instance codename prefixed by "apple,", + e.g. "apple,honshu". + + apple,antenna-sku: + $ref: /schemas/types.yaml#/definitions/string + description: Antenna SKU used to identify a specific antenna configuration + on Apple platforms. This is use to build firmware filenames, to allow + platforms with different antenna configs to have different firmware and/or + NVRAM. This would normally be filled in by the bootloader from platform + configuration data. + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml index 60de78f1bc7b..b3405f284580 100644 --- a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml +++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml @@ -20,8 +20,6 @@ properties: reg: true - spi-max-frequency: true - interrupts: maxItems: 1 @@ -51,7 +49,10 @@ required: - compatible - interrupts -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml index a677b056f112..f7cf135aa37f 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml @@ -66,6 +66,18 @@ properties: required: - iommus + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: State bits used by the AP to signal the WLAN Q6. + items: + - description: Signal bits used to enable/disable low power mode + on WCN6750 in the case of WoW (Wake on Wireless). + + qcom,smem-state-names: + description: The names of the state bits used for SMP2P output. + items: + - const: wlan-smp2p-out + required: - compatible - reg @@ -448,6 +460,8 @@ examples: <GIC_SPI 799 IRQ_TYPE_EDGE_RISING>; qcom,rproc = <&remoteproc_wpss>; memory-region = <&wlan_fw_mem>, <&wlan_ce_mem>; + qcom,smem-states = <&wlan_smp2p_out 0>; + qcom,smem-state-names = "wlan-smp2p-out"; wifi-firmware { iommus = <&apps_smmu 0x1c02 0x1>; }; diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml index 76199a67d628..b35d2f3ad1ad 100644 --- a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml @@ -29,12 +29,6 @@ description: > Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more information. - For SPI: - - In add of the properties below, please consult - Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI - related properties. - properties: compatible: items: @@ -52,8 +46,6 @@ properties: bindings. maxItems: 1 - spi-max-frequency: true - interrupts: description: The interrupt line. Should be IRQ_TYPE_EDGE_RISING. When SPI is used, this property is required. When SDIO is used, the "in-band" @@ -84,12 +76,15 @@ properties: mac-address: true -additionalProperties: false - required: - compatible - reg +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + examples: - | #include <dt-bindings/gpio/gpio.h> diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml index d68bb2ec1f7e..e31456730e9f 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml @@ -36,8 +36,6 @@ properties: This is required when connected via SPI, and optional when connected via SDIO. - spi-max-frequency: true - interrupts: minItems: 1 maxItems: 2 @@ -69,20 +67,22 @@ required: - compatible - interrupts -if: - properties: - compatible: - contains: - enum: - - ti,wl1271 - - ti,wl1273 - - ti,wl1281 - - ti,wl1283 -then: - required: - - ref-clock-frequency - -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + contains: + enum: + - ti,wl1271 + - ti,wl1273 + - ti,wl1281 + - ti,wl1283 + then: + required: + - ref-clock-frequency + +unevaluatedProperties: false examples: - | |