diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
8 files changed, 486 insertions, 18 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt index f16b99571af1..dd258674633c 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -11,6 +11,7 @@ Required properties: - compatible: should contain one of the following: * "brcm,bcm20702a1" + * "brcm,bcm4329-bt" * "brcm,bcm4330-bt" * "brcm,bcm43438-bt" * "brcm,bcm4345c5" @@ -22,7 +23,9 @@ Optional properties: - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt - shutdown-gpios: GPIO specifier, used to enable the BT module - device-wakeup-gpios: GPIO specifier, used to wakeup the controller - - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor. + deprecated, replaced by interrupts and + "host-wakeup" interrupt-names - clocks: 1 or 2 clocks as defined in clock-names below, in that order - clock-names: names for clock inputs, matching the clocks given - "extclk": deprecated, replaced by "txco" @@ -30,7 +33,14 @@ Optional properties: - "lpo": external low power 32.768 kHz clock - vbat-supply: phandle to regulator supply for VBAT - vddio-supply: phandle to regulator supply for VDDIO - + - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array + - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S + - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps + - pcm-frame-type: short, long + - pcm-sync-mode: slave, master + - pcm-clock-mode: slave, master + - interrupts: must be one, used to wakeup the host processor + - interrupt-names: must be "host-wakeup" Example: @@ -41,5 +51,6 @@ Example: bluetooth { compatible = "brcm,bcm43438-bt"; max-speed = <921600>; + brcm,bt-pcm-int-params = [01 02 00 01 01]; }; }; diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt index 27e1b4cebfbd..6bdcc3f84bd3 100644 --- a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt @@ -10,7 +10,6 @@ Required properties: - #size-cells: 0 - spi-max-frequency: Maximum frequency of the SPI bus the chip can operate at should be less than or equal to 18 MHz. - - device-wake-gpios: Wake up GPIO to wake up the TCAN device. - interrupt-parent: the phandle to the interrupt controller which provides the interrupt. - interrupts: interrupt specification for data-ready. @@ -23,6 +22,7 @@ Optional properties: reset. - device-state-gpios: Input GPIO that indicates if the device is in a sleep state or if the device is active. + - device-wake-gpios: Wake up GPIO to wake up the TCAN device. Example: tcan4x5x: tcan4x5x@0 { @@ -36,5 +36,5 @@ tcan4x5x: tcan4x5x@0 { interrupts = <14 GPIO_ACTIVE_LOW>; device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; }; diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt new file mode 100644 index 000000000000..320607cbbb17 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt @@ -0,0 +1,148 @@ +Atheros AR9331 built-in switch +============================= + +It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal +MDIO bus. All PHYs are built-in as well. + +Required properties: + + - compatible: should be: "qca,ar9331-switch" + - reg: Address on the MII bus for the switch. + - resets : Must contain an entry for each entry in reset-names. + - reset-names : Must include the following entries: "switch" + - interrupt-parent: Phandle to the parent interrupt controller + - interrupts: IRQ line for the switch + - interrupt-controller: Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. + - #interrupt-cells: must be 1 + - mdio: Container of PHY and devices on the switches MDIO bus. + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required and optional properties. +Examples: + +eth0: ethernet@19000000 { + compatible = "qca,ar9330-eth"; + reg = <0x19000000 0x200>; + interrupts = <4>; + + resets = <&rst 9>, <&rst 22>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; + clock-names = "eth", "mdio"; + + phy-mode = "mii"; + phy-handle = <&phy_port4>; +}; + +eth1: ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch10: switch@10 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "qca,ar9331-switch"; + reg = <0x10>; + resets = <&rst 8>; + reset-names = "switch"; + + interrupt-parent = <&miscintc>; + interrupts = <12>; + + interrupt-controller; + #interrupt-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch_port0: port@0 { + reg = <0x0>; + label = "cpu"; + ethernet = <ð1>; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch_port1: port@1 { + reg = <0x1>; + phy-handle = <&phy_port0>; + phy-mode = "internal"; + }; + + switch_port2: port@2 { + reg = <0x2>; + phy-handle = <&phy_port1>; + phy-mode = "internal"; + }; + + switch_port3: port@3 { + reg = <0x3>; + phy-handle = <&phy_port2>; + phy-mode = "internal"; + }; + + switch_port4: port@4 { + reg = <0x4>; + phy-handle = <&phy_port3>; + phy-mode = "internal"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&switch10>; + + phy_port0: phy@0 { + reg = <0x0>; + interrupts = <0>; + }; + + phy_port1: phy@1 { + reg = <0x1>; + interrupts = <0>; + }; + + phy_port2: phy@2 { + reg = <0x2>; + interrupts = <0>; + }; + + phy_port3: phy@3 { + reg = <0x3>; + interrupts = <0>; + }; + + phy_port4: phy@4 { + reg = <0x4>; + interrupts = <0>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt index 299c0dcd67db..250f8d8cdce4 100644 --- a/Documentation/devicetree/bindings/net/fsl-fman.txt +++ b/Documentation/devicetree/bindings/net/fsl-fman.txt @@ -403,6 +403,19 @@ PROPERTIES The settings and programming routines for internal/external MDIO are different. Must be included for internal MDIO. +- fsl,erratum-a011043 + Usage: optional + Value type: <boolean> + Definition: Indicates the presence of the A011043 erratum + describing that the MDIO_CFG[MDIO_RD_ER] bit may be falsely + set when reading internal PCS registers. MDIO reads to + internal PCS registers may result in having the + MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and + read data (MDIO_DATA[MDIO_DATA]) is correct. + Software may get false read error when reading internal + PCS registers through MDIO. As a workaround, all internal + MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. + For internal PHY device on internal mdio bus, a PHY node should be created. See the definition of the PHY node in booting-without-of.txt for an example of how to define a PHY (Internal PHY has no interrupt line). diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt index 8a08621a5b54..afbcaebf062e 100644 --- a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt +++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt @@ -14,7 +14,7 @@ Required properties: Should be "macirq" for the main MAC IRQ - clocks: Must contain a phandle for each entry in clock-names. - clock-names: The name of the clock listed in the clocks property. These are - "axi", "apb", "mac_main", "ptp_ref" for MT2712 SoC + "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC. - mac-address: See ethernet.txt in the same directory - phy-mode: See ethernet.txt in the same directory - mediatek,pericfg: A phandle to the syscon node that control ethernet @@ -23,8 +23,10 @@ Required properties: Optional properties: - mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. It should be defined for RGMII/MII interface. + It should be defined for RMII interface when the reference clock is from MT2712 SoC. - mediatek,rx-delay-ps: RX clock delay macro value. Default is 0. - It should be defined for RGMII/MII/RMII interface. + It should be defined for RGMII/MII interface. + It should be defined for RMII interface. Both delay properties need to be a multiple of 170 for RGMII interface, or will round down. Range 0~31*170. Both delay properties need to be a multiple of 550 for MII/RMII interface, @@ -34,13 +36,20 @@ or will round down. Range 0~31*550. reference clock, which is from external PHYs, is connected to RXC pin on MT2712 SoC. Otherwise, is connected to TXC pin. +- mediatek,rmii-clk-from-mac: boolean property, if present indicates that + MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only. - mediatek,txc-inverse: boolean property, if present indicates that 1. tx clock will be inversed in MII/RGMII case, 2. tx clock inside MAC will be inversed relative to reference clock which is from external PHYs in RMII case, and it rarely happen. + 3. the reference clock, which outputs to TXC pin will be inversed in RMII case + when the reference clock is from MT2712 SoC. - mediatek,rxc-inverse: boolean property, if present indicates that 1. rx clock will be inversed in MII/RGMII case. - 2. reference clock will be inversed when arrived at MAC in RMII case. + 2. reference clock will be inversed when arrived at MAC in RMII case, when + the reference clock is from external PHYs. + 3. the inside clock, which be sent to MAC, will be inversed in RMII case when + the reference clock is from MT2712 SoC. - assigned-clocks: mac_main and ptp_ref clocks - assigned-clock-parents: parent clocks of the assigned clocks @@ -50,29 +59,33 @@ Example: reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "macirq"; - phy-mode ="rgmii"; + phy-mode ="rgmii-rxid"; mac-address = [00 55 7b b5 7d f7]; clock-names = "axi", "apb", "mac_main", "ptp_ref", - "ptp_top"; + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; mediatek,tx-delay-ps = <1530>; mediatek,rx-delay-ps = <1530>; mediatek,rmii-rxc; mediatek,txc-inverse; mediatek,rxc-inverse; - snps,txpbl = <32>; - snps,rxpbl = <32>; + snps,txpbl = <1>; + snps,rxpbl = <1>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; snps,reset-active-low; }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 388ff48f53ae..44e2a4fab29e 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -8,8 +8,6 @@ Required properties: - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values. Required only if interface type is PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID - - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h - for applicable values Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays will be left at their default values, as set by the PHY's pin strapping. @@ -42,6 +40,14 @@ Optional property: Some MACs work with differential SGMII clock. See data manual for details. + - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h + for applicable values (deprecated) + + -tx-fifo-depth - As defined in the ethernet-controller.yaml. Values for + the depth can be found in dt-bindings/net/ti-dp83867.h + -rx-fifo-depth - As defined in the ethernet-controller.yaml. Values for + the depth can be found in dt-bindings/net/ti-dp83867.h + Note: ti,min-output-impedance and ti,max-output-impedance are mutually exclusive. When both properties are present ti,max-output-impedance takes precedence. @@ -55,7 +61,7 @@ Example: reg = <0>; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; - ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; Datasheet can be found: diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 017128394a3e..616c87746d6f 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -50,7 +50,7 @@ Optional properties: entry in clock-names. - clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and - "cxo_ref_clk_pin" for "qcom,wcn3990-wifi" + "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi" compatible target. - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into @@ -88,6 +88,9 @@ Optional properties: of the host capability QMI request - qcom,xo-cal-data: xo cal offset to be configured in xo trim register. +- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically + mapped msa region. + Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller. @@ -185,4 +188,5 @@ wifi@18000000 { vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; + qcom,msa-fixed-perm; }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml new file mode 100644 index 000000000000..a1717db36dba --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml @@ -0,0 +1,273 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies ath11k wireless devices Generic Binding + +maintainers: + - Kalle Valo <kvalo@codeaurora.org> + +description: | + These are dt entries for Qualcomm Technologies, Inc. IEEE 802.11ax + devices, for example like AHB based IPQ8074. + +properties: + compatible: + const: qcom,ipq8074-wifi + + reg: + maxItems: 1 + + interrupts: + items: + - description: misc-pulse1 interrupt events + - description: misc-latch interrupt events + - description: sw exception interrupt events + - description: watchdog interrupt events + - description: interrupt event for ring CE0 + - description: interrupt event for ring CE1 + - description: interrupt event for ring CE2 + - description: interrupt event for ring CE3 + - description: interrupt event for ring CE4 + - description: interrupt event for ring CE5 + - description: interrupt event for ring CE6 + - description: interrupt event for ring CE7 + - description: interrupt event for ring CE8 + - description: interrupt event for ring CE9 + - description: interrupt event for ring CE10 + - description: interrupt event for ring CE11 + - description: interrupt event for ring host2wbm-desc-feed + - description: interrupt event for ring host2reo-re-injection + - description: interrupt event for ring host2reo-command + - description: interrupt event for ring host2rxdma-monitor-ring3 + - description: interrupt event for ring host2rxdma-monitor-ring2 + - description: interrupt event for ring host2rxdma-monitor-ring1 + - description: interrupt event for ring reo2ost-exception + - description: interrupt event for ring wbm2host-rx-release + - description: interrupt event for ring reo2host-status + - description: interrupt event for ring reo2host-destination-ring4 + - description: interrupt event for ring reo2host-destination-ring3 + - description: interrupt event for ring reo2host-destination-ring2 + - description: interrupt event for ring reo2host-destination-ring1 + - description: interrupt event for ring rxdma2host-monitor-destination-mac3 + - description: interrupt event for ring rxdma2host-monitor-destination-mac2 + - description: interrupt event for ring rxdma2host-monitor-destination-mac1 + - description: interrupt event for ring ppdu-end-interrupts-mac3 + - description: interrupt event for ring ppdu-end-interrupts-mac2 + - description: interrupt event for ring ppdu-end-interrupts-mac1 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac3 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac2 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac1 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac3 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac2 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac1 + - description: interrupt event for ring rxdma2host-destination-ring-mac3 + - description: interrupt event for ring rxdma2host-destination-ring-mac2 + - description: interrupt event for ring rxdma2host-destination-ring-mac1 + - description: interrupt event for ring host2tcl-input-ring4 + - description: interrupt event for ring host2tcl-input-ring3 + - description: interrupt event for ring host2tcl-input-ring2 + - description: interrupt event for ring host2tcl-input-ring1 + - description: interrupt event for ring wbm2host-tx-completions-ring3 + - description: interrupt event for ring wbm2host-tx-completions-ring2 + - description: interrupt event for ring wbm2host-tx-completions-ring1 + - description: interrupt event for ring tcl2host-status-ring + + + interrupt-names: + items: + - const: misc-pulse1 + - const: misc-latch + - const: sw-exception + - const: watchdog + - const: ce0 + - const: ce1 + - const: ce2 + - const: ce3 + - const: ce4 + - const: ce5 + - const: ce6 + - const: ce7 + - const: ce8 + - const: ce9 + - const: ce10 + - const: ce11 + - const: host2wbm-desc-feed + - const: host2reo-re-injection + - const: host2reo-command + - const: host2rxdma-monitor-ring3 + - const: host2rxdma-monitor-ring2 + - const: host2rxdma-monitor-ring1 + - const: reo2ost-exception + - const: wbm2host-rx-release + - const: reo2host-status + - const: reo2host-destination-ring4 + - const: reo2host-destination-ring3 + - const: reo2host-destination-ring2 + - const: reo2host-destination-ring1 + - const: rxdma2host-monitor-destination-mac3 + - const: rxdma2host-monitor-destination-mac2 + - const: rxdma2host-monitor-destination-mac1 + - const: ppdu-end-interrupts-mac3 + - const: ppdu-end-interrupts-mac2 + - const: ppdu-end-interrupts-mac1 + - const: rxdma2host-monitor-status-ring-mac3 + - const: rxdma2host-monitor-status-ring-mac2 + - const: rxdma2host-monitor-status-ring-mac1 + - const: host2rxdma-host-buf-ring-mac3 + - const: host2rxdma-host-buf-ring-mac2 + - const: host2rxdma-host-buf-ring-mac1 + - const: rxdma2host-destination-ring-mac3 + - const: rxdma2host-destination-ring-mac2 + - const: rxdma2host-destination-ring-mac1 + - const: host2tcl-input-ring4 + - const: host2tcl-input-ring3 + - const: host2tcl-input-ring2 + - const: host2tcl-input-ring1 + - const: wbm2host-tx-completions-ring3 + - const: wbm2host-tx-completions-ring2 + - const: wbm2host-tx-completions-ring1 + - const: tcl2host-status-ring + + qcom,rproc: + $ref: /schemas/types.yaml#definitions/phandle + description: + DT entry of q6v5-wcss remoteproc driver. + Phandle to a node that can contain the following properties + * compatible + * reg + * reg-names + +required: + - compatible + - reg + - interrupts + - interrupt-names + - qcom,rproc + +additionalProperties: false + +examples: + - | + + q6v5_wcss: q6v5_wcss@CD00000 { + compatible = "qcom,ipq8074-wcss-pil"; + reg = <0xCD00000 0x4040>, + <0x4AB000 0x20>; + reg-names = "qdsp6", + "rmb"; + }; + + wifi0: wifi@c000000 { + compatible = "qcom,ipq8074-wifi"; + reg = <0xc000000 0x2000000>; + interrupts = <0 320 1>, + <0 319 1>, + <0 318 1>, + <0 317 1>, + <0 316 1>, + <0 315 1>, + <0 314 1>, + <0 311 1>, + <0 310 1>, + <0 411 1>, + <0 410 1>, + <0 40 1>, + <0 39 1>, + <0 302 1>, + <0 301 1>, + <0 37 1>, + <0 36 1>, + <0 296 1>, + <0 295 1>, + <0 294 1>, + <0 293 1>, + <0 292 1>, + <0 291 1>, + <0 290 1>, + <0 289 1>, + <0 288 1>, + <0 239 1>, + <0 236 1>, + <0 235 1>, + <0 234 1>, + <0 233 1>, + <0 232 1>, + <0 231 1>, + <0 230 1>, + <0 229 1>, + <0 228 1>, + <0 224 1>, + <0 223 1>, + <0 203 1>, + <0 183 1>, + <0 180 1>, + <0 179 1>, + <0 178 1>, + <0 177 1>, + <0 176 1>, + <0 163 1>, + <0 162 1>, + <0 160 1>, + <0 159 1>, + <0 158 1>, + <0 157 1>, + <0 156 1>; + interrupt-names = "misc-pulse1", + "misc-latch", + "sw-exception", + "watchdog", + "ce0", + "ce1", + "ce2", + "ce3", + "ce4", + "ce5", + "ce6", + "ce7", + "ce8", + "ce9", + "ce10", + "ce11", + "host2wbm-desc-feed", + "host2reo-re-injection", + "host2reo-command", + "host2rxdma-monitor-ring3", + "host2rxdma-monitor-ring2", + "host2rxdma-monitor-ring1", + "reo2ost-exception", + "wbm2host-rx-release", + "reo2host-status", + "reo2host-destination-ring4", + "reo2host-destination-ring3", + "reo2host-destination-ring2", + "reo2host-destination-ring1", + "rxdma2host-monitor-destination-mac3", + "rxdma2host-monitor-destination-mac2", + "rxdma2host-monitor-destination-mac1", + "ppdu-end-interrupts-mac3", + "ppdu-end-interrupts-mac2", + "ppdu-end-interrupts-mac1", + "rxdma2host-monitor-status-ring-mac3", + "rxdma2host-monitor-status-ring-mac2", + "rxdma2host-monitor-status-ring-mac1", + "host2rxdma-host-buf-ring-mac3", + "host2rxdma-host-buf-ring-mac2", + "host2rxdma-host-buf-ring-mac1", + "rxdma2host-destination-ring-mac3", + "rxdma2host-destination-ring-mac2", + "rxdma2host-destination-ring-mac1", + "host2tcl-input-ring4", + "host2tcl-input-ring3", + "host2tcl-input-ring2", + "host2tcl-input-ring1", + "wbm2host-tx-completions-ring3", + "wbm2host-tx-completions-ring2", + "wbm2host-tx-completions-ring1", + "tcl2host-status-ring"; + qcom,rproc = <&q6v5_wcss>; + }; |