diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
17 files changed, 617 insertions, 45 deletions
diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt index 10587bdadbbe..26c77d985faf 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -2,11 +2,14 @@ Required properties: - compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2", - "brcm,genet-v3", "brcm,genet-v4". + "brcm,genet-v3", "brcm,genet-v4", "brcm,genet-v5". - reg: address and length of the register set for the device -- interrupts: must be two cells, the first cell is the general purpose - interrupt line, while the second cell is the interrupt for the ring - RX and TX queues operating in ring mode +- interrupts and/or interrupts-extended: must be two cells, the first cell + is the general purpose interrupt line, while the second cell is the + interrupt for the ring RX and TX queues operating in ring mode. An + optional third interrupt cell for Wake-on-LAN can be specified. + See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for information on the property specifics. - phy-mode: see ethernet.txt file in the same directory - #address-cells: should be 1 - #size-cells: should be 1 @@ -29,15 +32,15 @@ Optional properties: Required child nodes: -- mdio bus node: this node should always be present regarless of the PHY +- mdio bus node: this node should always be present regardless of the PHY configuration of the GENET instance MDIO bus node required properties: - compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2" - "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", the version has to match the - parent node compatible property (e.g: brcm,genet-v4 pairs with - brcm,genet-mdio-v4) + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5", the version + has to match the parent node compatible property (e.g: brcm,genet-v4 pairs + with brcm,genet-mdio-v4) - reg: address and length relative to the parent node base register address - #address-cells: address cell for MDIO bus addressing, should be 1 - #size-cells: size of the cells for MDIO bus addressing, should be 0 diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index ab0bb4247d14..4648948f7c3b 100644 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -2,8 +2,9 @@ Required properties: - compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", - "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio" -- reg: address and length of the regsiter set for the device, first one is the + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5" or + "brcm,unimac-mdio" +- reg: address and length of the register set for the device, first one is the base register, and the second one is optional and for indirect accesses to larger than 16-bits MDIO transactions - reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" diff --git a/Documentation/devicetree/bindings/net/can/holt_hi311x.txt b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt new file mode 100644 index 000000000000..23aa94eab207 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt @@ -0,0 +1,24 @@ +* Holt HI-311X stand-alone CAN controller device tree bindings + +Required properties: + - compatible: Should be one of the following: + - "holt,hi3110" for HI-3110 + - reg: SPI chip select. + - clocks: The clock feeding the CAN controller. + - interrupt-parent: The parent interrupt controller. + - interrupts: Should contain IRQ line for the CAN controller. + +Optional properties: + - vdd-supply: Regulator that powers the CAN controller. + - xceiver-supply: Regulator that powers the CAN transceiver. + +Example: + can0: can@1 { + compatible = "holt,hi3110"; + reg = <1>; + clocks = <&clk32m>; + interrupt-parent = <&gpio4>; + interrupts = <13 IRQ_TYPE_EDGE_RISING>; + vdd-supply = <®5v0>; + xceiver-supply = <®5v0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/ti_hecc.txt b/Documentation/devicetree/bindings/net/can/ti_hecc.txt new file mode 100644 index 000000000000..e0f0a7cfe329 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/ti_hecc.txt @@ -0,0 +1,32 @@ +Texas Instruments High End CAN Controller (HECC) +================================================ + +This file provides information, what the device node +for the hecc interface contains. + +Required properties: +- compatible: "ti,am3517-hecc" +- reg: addresses and lengths of the register spaces for 'hecc', 'hecc-ram' + and 'mbx' +- reg-names :"hecc", "hecc-ram", "mbx" +- interrupts: interrupt mapping for the hecc interrupts sources +- clocks: clock phandles (see clock bindings for details) + +Optional properties: +- ti,use-hecc1int: if provided configures HECC to produce all interrupts + on HECC1INT interrupt line. By default HECC0INT interrupt + line will be used. +- xceiver-supply: regulator that powers the CAN transceiver + +Example: + +For am3517evm board: + hecc: can@5c050000 { + compatible = "ti,am3517-hecc"; + reg = <0x5c050000 0x80>, + <0x5c053000 0x180>, + <0x5c052000 0x200>; + reg-names = "hecc", "hecc-ram", "mbx"; + interrupts = <24>; + clocks = <&hecc_ck>; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt new file mode 100644 index 000000000000..04f2965a4467 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -0,0 +1,105 @@ +SMSC/MicroChip LAN9303 three port ethernet switch +------------------------------------------------- + +Required properties: + +- compatible: should be + - "smsc,lan9303-i2c" for I2C managed mode + or + - "smsc,lan9303-mdio" for mdio managed mode + +Optional properties: + +- reset-gpios: GPIO to be used to reset the whole device +- reset-duration: reset duration in milliseconds, defaults to 200 ms + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. The CPU port of this switch is always port 0. + +Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is +configured to use 1/2/3 instead. This hardware configuration will be +auto-detected and mapped accordingly. + +Example: + +I2C managed mode: + + master: masterdevice@X { + status = "okay"; + + fixed-link { /* RMII fixed link to LAN9303 */ + speed = <100>; + full-duplex; + }; + }; + + switch: switch@a { + compatible = "smsc,lan9303-i2c"; + reg = <0xa>; + status = "okay"; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <200>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { /* RMII fixed link to master */ + reg = <0>; + label = "cpu"; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + +MDIO managed mode: + + master: masterdevice@X { + status = "okay"; + phy-handle = <&switch>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch: switch-phy@0 { + compatible = "smsc,lan9303-mdio"; + reg = <0>; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <100>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt new file mode 100644 index 000000000000..a9bc27b93ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -0,0 +1,92 @@ +Mediatek MT7530 Ethernet switch +================================ + +Required properties: + +- compatible: Must be compatible = "mediatek,mt7530"; +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part + on multi-chip module belong to MT7623A has or the remotely standalone + chip as the function MT7623N reference board provided for. +- core-supply: Phandle to the regulator node necessary for the core power. +- io-supply: Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt + for details for the regulator setup on these boards. + +If the property mediatek,mcm isn't defined, following property is required + +- reset-gpios: Should be a gpio specifier for a reset line. + +Else, following properties are required + +- resets : Phandle pointing to the system reset controller with + line index for the ethsys. +- reset-names : Should be set to "mcm". + +Required properties for the child nodes within ports container: + +- reg: Port address described must be 6 for CPU port and from 0 to 5 for + user ports. +- phy-mode: String, must be either "trgmii" or "rgmii" for port labeled + "cpu". + +See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +required, optional properties and how the integrated switch subnodes must +be specified. + +Example: + + &mdio0 { + switch@0 { + compatible = "mediatek,mt7530"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + reset-gpios = <&pio 33 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/moxa,moxart-mac.txt b/Documentation/devicetree/bindings/net/faraday,ftmac.txt index 583418b2c127..be4f55e23bf7 100644 --- a/Documentation/devicetree/bindings/net/moxa,moxart-mac.txt +++ b/Documentation/devicetree/bindings/net/faraday,ftmac.txt @@ -1,8 +1,11 @@ -MOXA ART Ethernet Controller +Faraday Ethernet Controller Required properties: -- compatible : Must be "moxa,moxart-mac" +- compatible : Must contain "faraday,ftmac", as well as one of + the SoC specific identifiers: + "andestech,atmac100" + "moxa,moxart-mac" - reg : Should contain register location and length - interrupts : Should contain the mac interrupt number diff --git a/Documentation/devicetree/bindings/net/ftgmac100.txt b/Documentation/devicetree/bindings/net/ftgmac100.txt new file mode 100644 index 000000000000..c1ce1680246f --- /dev/null +++ b/Documentation/devicetree/bindings/net/ftgmac100.txt @@ -0,0 +1,35 @@ +* Faraday Technology FTGMAC100 gigabit ethernet controller + +Required properties: +- compatible: "faraday,ftgmac100" + + Must also contain one of these if used as part of an Aspeed AST2400 + or 2500 family SoC as they have some subtle tweaks to the + implementation: + + - "aspeed,ast2400-mac" + - "aspeed,ast2500-mac" + +- reg: Address and length of the register set for the device +- interrupts: Should contain ethernet controller interrupt + +Optional properties: +- phy-mode: See ethernet.txt file in the same directory. If the property is + absent, "rgmii" is assumed. Supported values are "rgmii*" and "rmii" for + aspeed parts. Other (unknown) parts will accept any value. +- use-ncsi: Use the NC-SI stack instead of an MDIO PHY. Currently assumes + rmii (100bT) but kept as a separate property in case NC-SI grows support + for a gigabit link. +- no-hw-checksum: Used to disable HW checksum support. Here for backward + compatibility as the driver now should have correct defaults based on + the SoC. + +Example: + + mac0: ethernet@1e660000 { + compatible = "aspeed,ast2500-mac", "faraday,ftgmac100"; + reg = <0x1e660000 0x180>; + interrupts = <2>; + status = "okay"; + use-ncsi; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt b/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt new file mode 100644 index 000000000000..a1046e636fa1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt @@ -0,0 +1,28 @@ +* CA8210 IEEE 802.15.4 * + +Required properties: + - compatible: Should be "cascoda,ca8210" + - reg: Controlling chip select + - spi-max-frequency: Maximum clock speed, should be *less than* + 4000000 + - spi-cpol: Requires inverted clock polarity + - reset-gpio: GPIO attached to reset + - irq-gpio: GPIO attached to IRQ +Optional properties: + - extclock-enable: Include for the ca8210 to route its 16MHz clock + to an output + - extclock-freq: Frequency in Hz of the external clock + - extclock-gpio: GPIO of the ca8210 to output the clock on + +Example: + ca8210@0 { + compatible = "cascoda,ca8210"; + reg = <0>; + spi-max-frequency = <3000000>; + spi-cpol; + reset-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; + irq-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + extclock-enable; + extclock-freq = 16000000; + extclock-gpio = 2; + }; diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt index 5fbab29718e8..c329608fa887 100644 --- a/Documentation/devicetree/bindings/net/marvell,prestera.txt +++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt @@ -32,19 +32,16 @@ DFX Server bindings ------------------- Required properties: -- compatible: must be "marvell,dfx-server" +- compatible: must be "marvell,dfx-server", "simple-bus" +- ranges: describes the address mapping of a memory-mapped bus. - reg: address and length of the register set for the device. Example: -dfx-registers { - compatible = "simple-bus"; +dfx-server { + compatible = "marvell,dfx-server", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>; - - dfx: dfx@0 { - compatible = "marvell,dfx-server"; - reg = <0 0x100000>; - }; + reg = <MBUS_ID(0x08, 0x00) 0 0x100000>; }; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt index 9417e54c26c0..ccdabdcc8618 100644 --- a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -7,17 +7,20 @@ interface. Required properties: - compatible: "marvell,orion-mdio" -- reg: address and length of the SMI register +- reg: address and length of the MDIO registers. When an interrupt is + not present, the length is the size of the SMI register (4 bytes) + otherwise it must be 0x84 bytes to cover the interrupt control + registers. Optional properties: - interrupts: interrupt line number for the SMI error/done interrupt -- clocks: Phandle to the clock control device and gate bit +- clocks: phandle for up to three required clocks for the MDIO instance The child nodes of the MDIO driver are the individual PHY devices connected to this MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. -Example at the SoC level: +Example at the SoC level without an interrupt property: mdio { #address-cells = <1>; @@ -26,6 +29,16 @@ mdio { reg = <0xd0072004 0x4>; }; +Example with an interrupt property: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x84>; + interrupts = <30>; +}; + And at the board level: mdio { diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index 4754364df4c6..6b4956beff8c 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -1,17 +1,28 @@ -* Marvell Armada 375 Ethernet Controller (PPv2) +* Marvell Armada 375 Ethernet Controller (PPv2.1) + Marvell Armada 7K/8K Ethernet Controller (PPv2.2) Required properties: -- compatible: should be "marvell,armada-375-pp2" +- compatible: should be one of: + "marvell,armada-375-pp2" + "marvell,armada-7k-pp2" - reg: addresses and length of the register sets for the device. - Must contain the following register sets: + For "marvell,armada-375-pp2", must contain the following register + sets: - common controller registers - LMS registers - In addition, at least one port register set is required. -- clocks: a pointer to the reference clocks for this device, consequently: - - main controller clock - - GOP clock -- clock-names: names of used clocks, must be "pp_clk" and "gop_clk". + - one register area per Ethernet port + For "marvell,armada-7k-pp2", must contain the following register + sets: + - packet processor registers + - networking interfaces registers + +- clocks: pointers to the reference clocks for this device, consequently: + - main controller clock (for both armada-375-pp2 and armada-7k-pp2) + - GOP clock (for both armada-375-pp2 and armada-7k-pp2) + - MG clock (only for armada-7k-pp2) +- clock-names: names of used clocks, must be "pp_clk", "gop_clk" and + "mg_clk" (the latter only for armada-7k-pp2). The ethernet ports are represented by subnodes. At least one port is required. @@ -19,8 +30,10 @@ required. Required properties (port): - interrupts: interrupt for the port -- port-id: should be '0' or '1' for ethernet ports, and '2' for the - loopback port +- port-id: ID of the port from the MAC point of view +- gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the + GOP (Group Of Ports) point of view. This ID is used to index the + per-port registers in the second register area. - phy-mode: See ethernet.txt file in the same directory Optional properties (port): @@ -29,7 +42,7 @@ Optional properties (port): - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). -Example: +Example for marvell,armada-375-pp2: ethernet@f0000 { compatible = "marvell,armada-375-pp2"; @@ -57,3 +70,30 @@ ethernet@f0000 { phy-mode = "gmii"; }; }; + +Example for marvell,armada-7k-pp2: + +cpm_ethernet: ethernet@0 { + compatible = "marvell,armada-7k-pp22"; + reg = <0x0 0x100000>, <0x129000 0xb000>; + clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, <&cpm_syscon0 1 5>; + clock-names = "pp_clk", "gop_clk", "gp_clk"; + + eth0: eth0 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + gop-port-id = <0>; + }; + + eth1: eth1 { + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + gop-port-id = <2>; + }; + + eth2: eth2 { + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + port-id = <2>; + gop-port-id = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/mdio.txt b/Documentation/devicetree/bindings/net/mdio.txt new file mode 100644 index 000000000000..96a53f89aa6e --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio.txt @@ -0,0 +1,37 @@ +Common MDIO bus properties. + +These are generic properties that can apply to any MDIO bus. + +Optional properties: +- reset-gpios: One GPIO that control the RESET lines of all PHYs on that MDIO + bus. +- reset-delay-us: RESET pulse width in microseconds. + +A list of child nodes, one per device on the bus is expected. These +should follow the generic phy.txt, or a device specific binding document. + +The 'reset-delay-us' indicates the RESET signal pulse width in microseconds and +applies to all PHY devices. It must therefore be appropriately determined based +on all PHY requirements (maximum value of all per-PHY RESET pulse widths). + +Example : +This example shows these optional properties, plus other properties +required for the TI Davinci MDIO driver. + + davinci_mdio: ethernet@0x5c030000 { + compatible = "ti,davinci_mdio"; + reg = <0x5c030000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + reset-delay-us = <2>; + + ethphy0: ethernet-phy@1 { + reg = <1>; + }; + + ethphy1: ethernet-phy@3 { + reg = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt index 32b35a07abe4..c627bbb3009e 100644 --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -5,8 +5,8 @@ Required properties: - spi-max-frequency: Maximum SPI frequency (<= 2000000). - interrupt-parent: phandle of parent interrupt handler. - interrupts: A single interrupt specifier. -- ti,enable-gpios: Two GPIO entries used for 'EN' and 'EN2' pins on the - TRF7970A. +- ti,enable-gpios: One or two GPIO entries used for 'EN' and 'EN2' pins on the + TRF7970A. EN2 is optional. - vin-supply: Regulator for supply voltage to VIN pin Optional SoC Specific Properties: @@ -21,6 +21,8 @@ Optional SoC Specific Properties: - t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum where an extra byte is returned by Read Multiple Block commands issued to Type 5 tags. +- vdd-io-supply: Regulator specifying voltage for vdd-io +- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz Example (for ARM-based BeagleBone with TRF7970A on SPI1): @@ -39,10 +41,12 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1): <&gpio2 5 GPIO_ACTIVE_LOW>; vin-supply = <&ldo3_reg>; vin-voltage-override = <5000000>; + vdd-io-supply = <&ldo2_reg>; autosuspend-delay = <30000>; irq-status-read-quirk; en2-rf-quirk; t5t-rmb-extra-byte-quirk; + clock-frequency = <27120000>; status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/net/nokia-bluetooth.txt b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt new file mode 100644 index 000000000000..42be7dc9a70b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt @@ -0,0 +1,51 @@ +Nokia Bluetooth Chips +--------------------- + +Nokia phones often come with UART connected bluetooth chips from different +vendors and modified device API. Those devices speak a protocol named H4+ +(also known as h4p) by Nokia, which is similar to the H4 protocol from the +Bluetooth standard. In addition to the H4 protocol it specifies two more +UART status lines for wakeup of UART transceivers to improve power management +and a few new packet types used to negotiate uart speed. + +Required properties: + + - compatible: should contain "nokia,h4p-bluetooth" as well as one of the following: + * "brcm,bcm2048-nokia" + * "ti,wl1271-bluetooth-nokia" + - reset-gpios: GPIO specifier, used to reset the BT module (active low) + - bluetooth-wakeup-gpios: GPIO specifier, used to wakeup the BT module (active high) + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor (active high) + - clock-names: should be "sysclk" + - clocks: should contain a clock specifier for every name in clock-names + +Optional properties: + + - None + +Example: + +/ { + /* controlled (enabled/disabled) directly by BT module */ + bluetooth_clk: vctcxo { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + bluetooth { + compatible = "ti,wl1271-bluetooth-nokia", "nokia,h4p-bluetooth"; + + reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; /* gpio26 */ + host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ + bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* gpio37 */ + + clocks = <&bluetooth_clk>; + clock-names = "sysclk"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index d3bfc2b30fb5..c3a7be6615c5 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -7,9 +7,12 @@ Required properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupts: Should contain the STMMAC interrupts -- interrupt-names: Should contain the interrupt names "macirq" - "eth_wake_irq" if this interrupt is supported in the "interrupts" - property +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Valid interrupt names are: + - "macirq" (combined signal for various interrupt events) + - "eth_wake_irq" (the interrupt to manage the remote wake-up packet detection) + - "eth_lpi" (the interrupt that occurs when Tx or Rx enters/exits LPI state) - phy-mode: See ethernet.txt file in the same directory. - snps,reset-gpio gpio number for phy reset. - snps,reset-active-low boolean flag to indicate if phy reset is active low. @@ -28,9 +31,9 @@ Optional properties: clocks may be specified in derived bindings. - clock-names: One name for each entry in the clocks property, the first one should be "stmmaceth" and the second one should be "pclk". -- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is - available this clock is used for programming the Timestamp Addend Register. - If not passed then the system clock will be used and this is fine on some +- ptp_ref: this is the PTP reference clock; in case of the PTP is available + this clock is used for programming the Timestamp Addend Register. If not + passed then the system clock will be used and this is fine on some platforms. - tx-fifo-depth: See ethernet.txt file in the same directory - rx-fifo-depth: See ethernet.txt file in the same directory @@ -72,7 +75,45 @@ Optional properties: - snps,mb: mixed-burst - snps,rb: rebuild INCRx Burst - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. - +- Multiple RX Queues parameters: below the list of all the parameters to + configure the multiple RX queues: + - snps,rx-queues-to-use: number of RX queues to be used in the driver + - Choose one of these RX scheduling algorithms: + - snps,rx-sched-sp: Strict priority + - snps,rx-sched-wsp: Weighted Strict priority + - For each RX queue + - Choose one of these modes: + - snps,dcb-algorithm: Queue to be enabled as DCB + - snps,avb-algorithm: Queue to be enabled as AVB + - snps,map-to-dma-channel: Channel to map + - Specifiy specific packet routing: + - snps,route-avcp: AV Untagged Control packets + - snps,route-ptp: PTP Packets + - snps,route-dcbcp: DCB Control Packets + - snps,route-up: Untagged Packets + - snps,route-multi-broad: Multicast & Broadcast Packets + - snps,priority: RX queue priority (Range: 0x0 to 0xF) +- Multiple TX Queues parameters: below the list of all the parameters to + configure the multiple TX queues: + - snps,tx-queues-to-use: number of TX queues to be used in the driver + - Choose one of these TX scheduling algorithms: + - snps,tx-sched-wrr: Weighted Round Robin + - snps,tx-sched-wfq: Weighted Fair Queuing + - snps,tx-sched-dwrr: Deficit Weighted Round Robin + - snps,tx-sched-sp: Strict priority + - For each TX queue + - snps,weight: TX queue weight (if using a DCB weight algorithm) + - Choose one of these modes: + - snps,dcb-algorithm: TX queue will be working in DCB + - snps,avb-algorithm: TX queue will be working in AVB + [Attention] Queue 0 is reserved for legacy traffic + and so no AVB is available in this queue. + - Configure Credit Base Shaper (if AVB Mode selected): + - snps,send_slope: enable Low Power Interface + - snps,idle_slope: unlock on WoL + - snps,high_credit: max write outstanding req. limit + - snps,low_credit: max read outstanding req. limit + - snps,priority: TX queue priority (Range: 0x0 to 0xF) Examples: stmmac_axi_setup: stmmac-axi-config { @@ -81,12 +122,41 @@ Examples: snps,blen = <256 128 64 32 0 0 0>; }; + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,priority = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <2>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + + queue1 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3E800>; + snps,low_credit = <0xFFC18000>; + snps,priority = <0x1>; + }; + }; + gmac0: ethernet@e0800000 { compatible = "st,spear600-gmac"; reg = <0xe0800000 0x8000>; interrupt-parent = <&vic1>; - interrupts = <24 23>; - interrupt-names = "macirq", "eth_wake_irq"; + interrupts = <24 23 22>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; mac-address = [000000000000]; /* Filled in by U-Boot */ max-frame-size = <3800>; phy-mode = "gmii"; @@ -104,4 +174,6 @@ Examples: phy1: ethernet-phy@0 { }; }; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; }; diff --git a/Documentation/devicetree/bindings/net/ti,wilink-st.txt b/Documentation/devicetree/bindings/net/ti,wilink-st.txt new file mode 100644 index 000000000000..cbad73a84ac4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,wilink-st.txt @@ -0,0 +1,35 @@ +TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices + +TI WiLink devices have a UART interface for providing Bluetooth, FM radio, +and GPS over what's called "shared transport". The shared transport is +standard BT HCI protocol with additional channels for the other functions. + +These devices also have a separate WiFi interface as described in +wireless/ti,wlcore.txt. + +This bindings follows the UART slave device binding in +../serial/slave-device.txt. + +Required properties: + - compatible: should be one of the following: + "ti,wl1271-st" + "ti,wl1273-st" + "ti,wl1831-st" + "ti,wl1835-st" + "ti,wl1837-st" + +Optional properties: + - enable-gpios : GPIO signal controlling enabling of BT. Active high. + - vio-supply : Vio input supply (1.8V) + - vbat-supply : Vbat input supply (2.9-4.8V) + +Example: + +&serial0 { + compatible = "ns16550a"; + ... + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; +}; |