diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
15 files changed, 154 insertions, 16 deletions
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt index 33df3932168e..8db32384a486 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -27,6 +27,8 @@ property is used. - amd,serdes-cdr-rate: CDR rate speed selection - amd,serdes-pq-skew: PQ (data sampling) skew - amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable Example: xgbe_phy@e1240800 { @@ -41,4 +43,6 @@ Example: amd,serdes-cdr-rate = <2>, <2>, <7>; amd,serdes-pq-skew = <10>, <10>, <30>; amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index cfcc52705ed8..f55aa280d34f 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -4,14 +4,21 @@ Ethernet nodes are defined to describe on-chip ethernet interfaces in APM X-Gene SoC. Required properties for all the ethernet interfaces: -- compatible: Should be "apm,xgene-enet" +- compatible: Should state binding information from the following list, + - "apm,xgene-enet": RGMII based 1G interface + - "apm,xgene1-sgenet": SGMII based 1G interface + - "apm,xgene1-xgenet": XFI based 10G interface - reg: Address and length of the register set for the device. It contains the information of registers in the same order as described by reg-names - reg-names: Should contain the register set names - "enet_csr": Ethernet control and status register address space - "ring_csr": Descriptor ring control and status register address space - "ring_cmd": Descriptor ring command register address space -- interrupts: Ethernet main interrupt +- interrupts: Two interrupt specifiers can be specified. + - First is the Rx interrupt. This irq is mandatory. + - Second is the Tx completion interrupt. + This is supported only on SGMII based 1GbE and 10GbE interfaces. +- port-id: Port number (0 or 1) - clocks: Reference to the clock entry. - local-mac-address: MAC address assigned to this device - phy-connection-type: Interface type between ethernet device and PHY device @@ -46,6 +53,7 @@ Example: <0x0 0X10000000 0x0 0X200>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; interrupts = <0x0 0x3c 0x4>; + port-id = <0>; clocks = <&menetclk 0>; local-mac-address = [00 01 73 00 00 01]; phy-connection-type = "rgmii"; diff --git a/Documentation/devicetree/bindings/net/broadcom-sf2.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt index 30d487597ecb..30d487597ecb 100644 --- a/Documentation/devicetree/bindings/net/broadcom-sf2.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt diff --git a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt index 451fef26b4df..451fef26b4df 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/brcm,systemport.txt index 877da34145b0..877da34145b0 100644 --- a/Documentation/devicetree/bindings/net/broadcom-systemport.txt +++ b/Documentation/devicetree/bindings/net/brcm,systemport.txt diff --git a/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index ab0bb4247d14..ab0bb4247d14 100644 --- a/Documentation/devicetree/bindings/net/broadcom-mdio-unimac.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index e124847443f8..f0b4cd72411d 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -19,7 +19,9 @@ the parent DSA node. The maximum number of allowed child nodes is 4 (DSA_MAX_SWITCHES). Each of these switch child nodes should have the following required properties: -- reg : Describes the switch address on the MII bus +- reg : Contains two fields. The first one describes the + address on the MII bus. The second is the switch + number that must be unique in cascaded configurations - #address-cells : Must be 1 - #size-cells : Must be 0 diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 3fc360523bc9..41b3f3f864e8 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -19,6 +19,12 @@ The following properties are common to the Ethernet controllers: - phy: the same as "phy-handle" property, not recommended for new bindings. - phy-device: the same as "phy-handle" property, not recommended for new bindings. +- rx-fifo-depth: the size of the controller's receive fifo in bytes. This + is used for components that can have configurable receive fifo sizes, + and is useful for determining certain configuration settings such as + flow control thresholds. +- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This + is used for components that can have configurable fifo sizes. Child nodes of the Ethernet controller are typically the individual PHY devices connected via the MDIO bus (sometimes the MDIO bus controller is separate). diff --git a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt index d3bbdded4cbe..168f1be50912 100644 --- a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt +++ b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt @@ -6,11 +6,14 @@ Required properties: - spi-max-frequency: maximal bus speed, should be set to 7500000 depends sync or async operation mode - reg: the chipselect index - - interrupts: the interrupt generated by the device + - interrupts: the interrupt generated by the device. Non high-level + can occur deadlocks while handling isr. Optional properties: - reset-gpio: GPIO spec for the rstn pin - sleep-gpio: GPIO spec for the slp_tr pin + - xtal-trim: u8 value for fine tuning the internal capacitance + arrays of xtal pins: 0 = +0 pF, 0xf = +4.5 pF Example: @@ -18,6 +21,7 @@ Example: compatible = "atmel,at86rf231"; spi-max-frequency = <7500000>; reg = <0>; - interrupts = <19 1>; + interrupts = <19 4>; interrupt-parent = <&gpio3>; + xtal-trim = /bits/ 8 <0x06>; }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt index 0071883c08d8..fb6d49f184ed 100644 --- a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt +++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt @@ -13,11 +13,15 @@ Required properties: - cca-gpio: GPIO spec for the CCA pin - vreg-gpio: GPIO spec for the VREG pin - reset-gpio: GPIO spec for the RESET pin +Optional properties: + - amplified: include if the CC2520 is connected to a CC2591 amplifier + Example: cc2520@0 { compatible = "ti,cc2520"; reg = <0>; spi-max-frequency = <4000000>; + amplified; pinctrl-names = "default"; pinctrl-0 = <&cc2520_cape_pins>; fifo-gpio = <&gpio1 18 0>; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index f9c07710478d..d0e6fa38f335 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -49,6 +49,7 @@ Required properties: - compatible: Should be "ti,netcp-1.0" - clocks: phandle to the reference clocks for the subsystem. - dma-id: Navigator packet dma instance id. +- ranges: address range of NetCP (includes, Ethernet SS, PA and SA) Optional properties: - reg: register location and the size for the following register @@ -64,10 +65,30 @@ NetCP device properties: Device specification for NetCP sub-modules. 1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications. Required properties: - label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb. +- compatible: Must be one of below:- + "ti,netcp-gbe" for 1GbE on NetCP 1.4 + "ti,netcp-gbe-5" for 1GbE N NetCP 1.5 (N=5) + "ti,netcp-gbe-9" for 1GbE N NetCP 1.5 (N=9) + "ti,netcp-gbe-2" for 1GbE N NetCP 1.5 (N=2) + "ti,netcp-xgbe" for 10 GbE + - reg: register location and the size for the following register regions in the specified order. - - subsystem registers - - serdes registers + - switch subsystem registers + - sgmii port3/4 module registers (only for NetCP 1.4) + - switch module registers + - serdes registers (only for 10G) + + NetCP 1.4 ethss, here is the order + index #0 - switch subsystem registers + index #1 - sgmii port3/4 module registers + index #2 - switch module registers + + NetCP 1.5 ethss 9 port, 5 port and 2 port + index #0 - switch subsystem registers + index #1 - switch module registers + index #2 - serdes registers + - tx-channel: the navigator packet dma channel name for tx. - tx-queue: the navigator queue number associated with the tx dma channel. - interfaces: specification for each of the switch port to be registered as a @@ -120,14 +141,13 @@ Optional properties: Example binding: -netcp: netcp@2090000 { +netcp: netcp@2000000 { reg = <0x2620110 0x8>; reg-names = "efuse"; compatible = "ti,netcp-1.0"; #address-cells = <1>; #size-cells = <1>; - ranges; - + ranges = <0 0x2000000 0xfffff>; clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>; dma-coherent; /* big-endian; */ @@ -137,9 +157,9 @@ netcp: netcp@2090000 { #address-cells = <1>; #size-cells = <1>; ranges; - gbe@0x2090000 { + gbe@90000 { label = "netcp-gbe"; - reg = <0x2090000 0xf00>; + reg = <0x90000 0x300>, <0x90400 0x400>, <0x90800 0x700>; /* enable-ale; */ tx-queue = <648>; tx-channel = <8>; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index aaa696414f57..ba19d671e808 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -2,10 +2,13 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" - Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs. + Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP + available on sama5d3 SoCs. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". + Use "cdns,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. + Use "cdns,sama5d4-gem" for the Gigabit IP available on Atmel sama5d4 SoCs. - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt new file mode 100644 index 000000000000..5b6cd9b3f628 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt @@ -0,0 +1,35 @@ +* NXP Semiconductors NXP NCI NFC Controllers + +Required properties: +- compatible: Should be "nxp,nxp-nci-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the chip +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): + +&i2c2 { + + status = "okay"; + + npc100: npc100@29 { + + compatible = "nxp,nxp-nci-i2c"; + + reg = <0x29>; + clock-frequency = <100000>; + + interrupt-parent = <&gpio1>; + interrupts = <29 GPIO_ACTIVE_HIGH>; + + enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 8ca65cec52ae..f34fc3c81a75 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -35,15 +35,18 @@ Optional properties: - reset-names: Should contain the reset signal name "stmmaceth", if a reset phandle is given - max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock, - further clocks may be specified in derived bindings. +- clocks: If present, the first clock should be the GMAC main clock and + the second clock should be peripheral's register interface clock. Further + clocks may be specified in derived bindings. - clock-names: One name for each entry in the clocks property, the - first one should be "stmmaceth". + first one should be "stmmaceth" and the second one should be "pclk". - clk_ptp_ref: this is the PTP reference clock; in case of the PTP is available this clock is used for programming the Timestamp Addend Register. If not passed then the system clock will be used and this is fine on some platforms. - snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. +- tx-fifo-depth: See ethernet.txt file in the same directory +- rx-fifo-depth: See ethernet.txt file in the same directory Examples: @@ -58,6 +61,8 @@ Examples: phy-mode = "gmii"; snps,multicast-filter-bins = <256>; snps,perfect-filter-entries = <128>; + rx-fifo-depth = <16384>; + tx-fifo-depth = <16384>; clocks = <&clock>; clock-names = "stmmaceth"; }; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt new file mode 100644 index 000000000000..2a3d90de18ee --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -0,0 +1,47 @@ +TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices + +This node provides properties for controlling the wilink wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + - compatible: should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" + - interrupts : specifies attributes for the out-of-band interrupt. + +Optional properties: + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - ref-clock-frequency : ref clock frequency in Hz + - tcxo-clock-frequency : tcxo clock frequency in Hz + +Note: the *-clock-frequency properties assume internal clocks. In case of external +clock, new bindings (for parsing the clock nodes) have to be added. + +Example: + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; +}; |