1 files changed, 0 insertions, 104 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
deleted file mode 100644
index 16589fb6f420..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
+++ /dev/null
@@ -1,104 +0,0 @@
-Broadcom Cygnus GPIO/PINCONF Controller
-
-Required properties:
-
-- compatible:
-    Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio",
-    "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio"
-
-- reg:
-    Define the base and range of the I/O address space that contains the Cygnus
-GPIO/PINCONF controller registers
-
-- #gpio-cells:
-    Must be two. The first cell is the GPIO pin number (within the
-controller's pin space) and the second cell is used for the following:
-    bit[0]: polarity (0 for active high and 1 for active low)
-
-- gpio-controller:
-    Specifies that the node is a GPIO controller
-
-Optional properties:
-
-- interrupts:
-    Interrupt ID
-
-- interrupt-controller:
-    Specifies that the node is an interrupt controller
-
-- gpio-ranges:
-    Specifies the mapping between gpio controller and pin-controllers pins.
-    This requires 4 fields in cells defined as -
-    1. Phandle of pin-controller.
-    2. GPIO base pin offset.
-    3  Pin-control base pin offset.
-    4. number of gpio pins which are linearly mapped from pin base.
-
-Supported generic PINCONF properties in child nodes:
-
-- pins:
-    The list of pins (within the controller's own pin space) that properties
-in the node apply to. Pin names are "gpio-<pin>"
-
-- bias-disable:
-    Disable pin bias
-
-- bias-pull-up:
-    Enable internal pull up resistor
-
-- bias-pull-down:
-    Enable internal pull down resistor
-
-- drive-strength:
-    Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA)
-
-Example:
-	gpio_ccm: gpio@1800a000 {
-		compatible = "brcm,cygnus-ccm-gpio";
-		reg = <0x1800a000 0x50>,
-		      <0x0301d164 0x20>;
-		#gpio-cells = <2>;
-		gpio-controller;
-		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-controller;
-
-		touch_pins: touch_pins {
-			pwr: pwr {
-				pins = "gpio-0";
-				drive-strength = <16>;
-			};
-
-			event: event {
-				pins = "gpio-1";
-				bias-pull-up;
-			};
-		};
-	};
-
-	gpio_asiu: gpio@180a5000 {
-		compatible = "brcm,cygnus-asiu-gpio";
-		reg = <0x180a5000 0x668>;
-		#gpio-cells = <2>;
-		gpio-controller;
-		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-controller;
-		gpio-ranges = <&pinctrl 0 42 1>,
-				<&pinctrl 1 44 3>;
-	};
-
-	/*
-	 * Touchscreen that uses the CCM GPIO 0 and 1
-	 */
-	tsc {
-		...
-		...
-		gpio-pwr = <&gpio_ccm 0 0>;
-		gpio-event = <&gpio_ccm 1 0>;
-	};
-
-	/* Bluetooth that uses the ASIU GPIO 5, with polarity inverted */
-	bluetooth {
-		...
-		...
-		bcm,rfkill-bank-sel = <&gpio_asiu 5 1>
-	}