diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator/regulator.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/regulator.yaml | 200 |
1 files changed, 200 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/regulator/regulator.yaml b/Documentation/devicetree/bindings/regulator/regulator.yaml new file mode 100644 index 000000000000..02c3043ce419 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator.yaml @@ -0,0 +1,200 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Voltage/Current Regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +properties: + regulator-name: + description: A string used as a descriptive name for regulator outputs + $ref: "/schemas/types.yaml#/definitions/string" + + regulator-min-microvolt: + description: smallest voltage consumers may set + + regulator-max-microvolt: + description: largest voltage consumers may set + + regulator-microvolt-offset: + description: Offset applied to voltages to compensate for voltage drops + + regulator-min-microamp: + description: smallest current consumers may set + + regulator-max-microamp: + description: largest current consumers may set + + regulator-input-current-limit-microamp: + description: maximum input current regulator allows + + regulator-always-on: + description: boolean, regulator should never be disabled + type: boolean + + regulator-boot-on: + description: bootloader/firmware enabled regulator + type: boolean + + regulator-allow-bypass: + description: allow the regulator to go into bypass mode + type: boolean + + regulator-allow-set-load: + description: allow the regulator performance level to be configured + type: boolean + + regulator-ramp-delay: + description: ramp delay for regulator(in uV/us) For hardware which supports + disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay + = <0>) for disabling ramp delay. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-enable-ramp-delay: + description: The time taken, in microseconds, for the supply rail to + reach the target voltage, plus/minus whatever tolerance the board + design requires. This property describes the total system ramp time + required due to the combination of internal ramping of the regulator + itself, and board design issues such as trace capacitance and load + on the supply. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-settling-time-us: + description: Settling time, in microseconds, for voltage change if regulator + have the constant time for any level voltage change. This is useful + when regulator have exponential voltage change. + + regulator-settling-time-up-us: + description: Settling time, in microseconds, for voltage increase if + the regulator needs a constant time to settle after voltage increases + of any level. This is useful for regulators with exponential voltage + changes. + + regulator-settling-time-down-us: + description: Settling time, in microseconds, for voltage decrease if + the regulator needs a constant time to settle after voltage decreases + of any level. This is useful for regulators with exponential voltage + changes. + + regulator-soft-start: + description: Enable soft start so that voltage ramps slowly + type: boolean + + regulator-initial-mode: + description: initial operating mode. The set of possible operating modes + depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-allowed-modes: + description: list of operating modes that software is allowed to configure + for the regulator at run-time. Elements may be specified in any order. + The set of possible operating modes depends on the capabilities of + every hardware so each device binding document explains which values + the regulator supports. + $ref: "/schemas/types.yaml#/definitions/uint32-array" + + regulator-system-load: + description: Load in uA present on regulator that is not captured by + any consumer request. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-pull-down: + description: Enable pull down resistor when the regulator is disabled. + type: boolean + + regulator-over-current-protection: + description: Enable over current protection. + type: boolean + + regulator-active-discharge: + description: | + tristate, enable/disable active discharge of regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + + regulator-coupled-with: + description: Regulators with which the regulator is coupled. The linkage + is 2-way - all coupled regulators should be linked with each other. + A regulator should not be coupled with its supplier. + $ref: "/schemas/types.yaml#/definitions/phandle-array" + + regulator-coupled-max-spread: + description: Array of maximum spread between voltages of coupled regulators + in microvolts, each value in the array relates to the corresponding + couple specified by the regulator-coupled-with property. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-max-step-microvolt: + description: Maximum difference between current and target voltages + that can be changed safely in a single step. + +patternProperties: + ".*-supply$": + description: Input supply phandle(s) for this node + + regulator-state-(standby|mem|disk): + type: object + description: + sub-nodes for regulator state in Standby, Suspend-to-RAM, and + Suspend-to-DISK modes. Equivalent with standby, mem, and disk Linux + sleep states. + + properties: + regulator-on-in-suspend: + description: regulator should be on in suspend state. + type: boolean + + regulator-off-in-suspend: + description: regulator should be off in suspend state. + type: boolean + + regulator-suspend-min-microvolt: + description: minimum voltage may be set in suspend state. + + regulator-suspend-max-microvolt: + description: maximum voltage may be set in suspend state. + + regulator-suspend-microvolt: + description: the default voltage which regulator would be set in + suspend. This property is now deprecated, instead setting voltage + for suspend mode via the API which regulator driver provides is + recommended. + + regulator-changeable-in-suspend: + description: whether the default voltage and the regulator on/off + in suspend can be changed in runtime. + type: boolean + + regulator-mode: + description: operating mode in the given suspend state. The set + of possible operating modes depends on the capabilities of every + hardware so the valid modes are documented on each regulator device + tree binding document. + $ref: "/schemas/types.yaml#/definitions/uint32" + + additionalProperties: false + +examples: + - | + xyzreg: regulator@0 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + +... |