diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
8 files changed, 403 insertions, 21 deletions
diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt new file mode 100644 index 000000000000..78183182dad9 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -0,0 +1,160 @@ +Binding for TI/National Semiconductor LP872x Driver + +Required properties: + - compatible: "ti,lp8720" or "ti,lp8725" + - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725 + +Optional properties: + - ti,general-config: the value of LP872X_GENERAL_CFG register (u8) + (LP8720) + bit[2]: BUCK output voltage control by external DVS pin or register + 1 = external pin, 0 = bit7 of register 08h + bit[1]: sleep control by external DVS pin or register + 1 = external pin, 0 = bit6 of register 08h + bit[0]: time step unit(usec). 1 = 25, 0 = 50 + + (LP8725) + bit[7:6]: time step unit(usec). 00 = 32, 01 = 64, 10 = 128, 11 = 256 + bit[4]: BUCK2 enable control. 1 = enable, 0 = disable + bit[3]: BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh + bit[2]: BUCK1 output voltage control by external DVS pin or register + 1 = register 08h, 0 = DVS + bit[1]: LDO sleep control. 1 = sleep mode, 0 = normal + bit[0]: BUCK1 enable control, 1 = enable, 0 = disable + + For more details, please see the datasheet. + + - ti,update-config: define it when LP872X_GENERAL_CFG register should be set + - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. + - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. + - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + + Sub nodes for regulator_init_data + LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) + LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2) + For more details, please see the following binding document. + (Documentation/devicetree/bindings/regulator/regulator.txt) + +Datasheet + - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf + - LP8725: http://www.ti.com/lit/ds/symlink/lp8725.pdf + +Example 1) LP8720 + +lp8720@7d { + compatible = "ti,lp8720"; + reg = <0x7d>; + + /* external DVS pin used, timestep is 25usec */ + ti,general-config = /bits/ 8 <0x03>; + ti,update-config; + + /* + * The dvs-gpio depends on the processor environment. + * For example, following GPIO specifier means GPIO134 in OMAP4. + */ + ti,dvs-gpio = <&gpio5 6 0>; + ti,dvs-vsel = /bits/ 8 <1>; /* SEL_V2 */ + ti,dvs-state = /bits/ 8 <1>; /* DVS_HIGH */ + + vaf: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vmmc: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_io: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcam_core: ldo4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2850000>; + regulator-boot-on; + }; + + vcam: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcc: buck { + regulator-name = "VBUCK"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2300000>; + }; +}; + +Example 2) LP8725 + +lp8725@7a { + compatible = "ti,lp8725"; + reg = <0x7a>; + + /* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */ + ti,general-config = /bits/ 8 <0xdd>; + ti,update-config; + + vcam_io: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_core: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcmmb_io: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcmmb_core: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vaux1: lilo1 { + regulator-name = "VAUX1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vaux2: lilo2 { + regulator-name = "VAUX2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vcc1: buck1 { + regulator-name = "VBUCK1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; + + vcc2: buck2 { + regulator-name = "VBUCK2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt new file mode 100644 index 000000000000..4f15d8a1bfd0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -0,0 +1,21 @@ +* Maxim MAX8973 Voltage Regulator + +Required properties: + +- compatible: must be "maxim,max8973" +- reg: the i2c slave address of the regulator. It should be 0x1b. + +Any standard regulator properties can be used to configure the single max8973 +DCDC. + +Example: + + max8973@1b { + compatible = "maxim,max8973"; + reg = <0x1b>; + + regulator-min-microvolt = <935000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt index 9e5e51d78868..5c186a7a77ba 100644 --- a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -1,6 +1,6 @@ * Maxim MAX8997 Voltage and Current Regulator -The Maxim MAX8997 is a multi-function device which includes volatage and +The Maxim MAX8997 is a multi-function device which includes voltage and current regulators, rtc, charger controller and other sub-blocks. It is interfaced to the host controller using a i2c interface. Each sub-block is addressed by the host system using different i2c slave address. This document diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt new file mode 100644 index 000000000000..d5a308629c57 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -0,0 +1,72 @@ +* palmas regulator IP block devicetree bindings + +Required properties: +- compatible : Should be from the list + ti,twl6035-pmic + ti,twl6036-pmic + ti,twl6037-pmic + ti,tps65913-pmic + ti,tps65914-pmic +and also the generic series names + ti,palmas-pmic +- interrupt-parent : The parent interrupt controller which is palmas. +- interrupts : The interrupt number and the type which can be looked up here: + arch/arm/boot/dts/include/dt-bindings/interrupt-controller/irq.h +- interrupts-name: The names of the individual interrupts. + +Optional properties: +- ti,ldo6-vibrator : ldo6 is in vibrator mode + +Optional nodes: +- regulators : Must contain a sub-node per regulator from the list below. + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a + description of standard properties for these sub-nodes. + Additional custom properties are listed below. + + For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP, + smps45, smps457, smps7 depending on variant, smps6, smps[8-10], + ldo[1-9], ldoln, ldousb. + + Optional sub-node properties: + ti,warm-reset - maintain voltage during warm reset(boolean) + ti,roof-floor - control voltage selection by pin(boolean) + ti,sleep-mode - mode to adopt in pmic sleep 0 - off, 1 - auto, + 2 - eco, 3 - forced pwm + ti,tstep - slope control 0 - Jump, 1 10mV/us, 2 5mV/us, 3 2.5mV/us + ti,smps-range - OTP has the wrong range set for the hardware so override + 0 - low range, 1 - high range. + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupts-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps12_reg : smps12 { + regulator-name = "smps12"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,warm-reset; + ti,roof-floor; + ti,mode-sleep = <0>; + ti,tstep = <0>; + ti,smps-range = <1>; + }; + + ldo1_reg: ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index ecfc6ccd67ef..48a3b8e5d6bd 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -9,6 +9,7 @@ Optional properties: - regulator-max-microamp: largest current consumers may set - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator +- regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt index a35ff99003a5..d1660a90fc06 100644 --- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -1,6 +1,6 @@ * Samsung S5M8767 Voltage and Current Regulator -The Samsung S5M8767 is a multi-function device which includes volatage and +The Samsung S5M8767 is a multi-function device which includes voltage and current regulators, rtc, charger controller and other sub-blocks. It is interfaced to the host controller using a i2c interface. Each sub-block is addressed by the host system using different i2c slave address. This document @@ -103,13 +103,13 @@ Example: s5m8767,pmic-buck-default-dvs-idx = <0>; - s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ - <&gpx0 1 1 0 0>, /* DVS2 */ - <&gpx0 2 1 0 0>; /* DVS3 */ + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ + <&gpx0 1 0>, /* DVS2 */ + <&gpx0 2 0>; /* DVS3 */ - s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ - <&gpx2 4 1 0 0>, /* SET2 */ - <&gpx2 5 1 0 0>; /* SET3 */ + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ + <&gpx2 4 0>, /* SET2 */ + <&gpx2 5 0>; /* SET3 */ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, <1250000>, <1200000>, diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt new file mode 100644 index 000000000000..2e57a33e9029 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -0,0 +1,128 @@ +Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs + +Required Properties: +- compatible: Should be one of: + - "ti,abb-v1" for older SoCs like OMAP3 + - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + - "base-address" - contains base address of ABB module + - "int-address" - contains address of interrupt register for ABB module + (also see Optional properties) +- #address-cell: should be 0 +- #size-cell: should be 0 +- clocks: should point to the clock node used by ABB module +- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module + to settle down(target time for SR2_WTCNT_VALUE). +- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for + computing settling time from SoC Documentation for ABB module(clock + cycles for SR2_WTCNT_VALUE). +- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask + indicating LDO tranxdone (operation complete). +- ti,abb_info: An array of 6-tuples u32 items providing information about ABB + configuration needed per operational voltage of the device. + Each item consists of the following in the same order: + volt: voltage in uV - Only used to index ABB information. + ABB mode: one of the following: + 0-bypass + 1-Forward Body Bias(FBB) + 3-Reverse Body Bias(RBB) + efuse: (see Optional properties) + RBB enable efuse Mask: (See Optional properties) + FBB enable efuse Mask: (See Optional properties) + Vset value efuse Mask: (See Optional properties) + + NOTE: If more than 1 entry is present, then regulator is setup to change + voltage, allowing for various modes to be selected indexed off + the regulator. Further, ABB LDOs are considered always-on by + default. + +Optional Properties: +- reg-names: In addition to the required properties, the following are optional + - "efuse-address" - Contains efuse base address used to pick up ABB info. + - "ldo-address" - Contains address of ABB LDO overide register address. + "efuse-address" is required for this. +- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override + register to provide override vset value. +- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO + override register to enable override vset value. +- ti,abb_opp_sel: Addendum to the description in required properties + efuse: Mandatory if 'efuse-address' register is defined. Provides offset + from efuse-address to pick up ABB characteristics. Set to 0 if + 'efuse-address' is not defined. + RBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to RBB mode if value at "efuse-address" + + efuse maps to RBB mask. Set to 0 to ignore this. + FBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to FBB mode if value at "efuse-address" + + efuse maps to FBB mask (valid only if RBB mask does not match) + Set to 0 to ignore this. + Vset value efuse Mask: Mandatory if ldo-address is set. Picks up from + efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address. + +Example #1: Simplest configuration (no efuse data, hard coded ABB table): +abb_x: regulator-abb-x { + compatible = "ti,abb-v1"; + regulator-name = "abb_x"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 1012500 0 0 0 0 0 /* Bypass */ + 1200000 3 0 0 0 0 /* RBB mandatory */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #2: Efuse bits contain ABB mode setting (no LDO override capability) +abb_y: regulator-abb-y { + compatible = "ti,abb-v2"; + regulator-name = "abb_y"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; + reg-names = "base-address", "int-address", "efuse-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1012500 0 0 0x40000 0 0 /* RBB optional */ + 1200000 0 0x4 0 0x40000 0 /* FBB optional */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #3: Efuse bits contain ABB mode setting and LDO override capability +abb_z: regulator-abb-z { + compatible = "ti,abb-v2"; + regulator-name = "abb_z"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, + <0x4a002194 0x8>, <0x4ae0C314 0x4>; + reg-names = "base-address", "int-address", + "efuse-address", "ldo-address"; + ti,tranxdone-status-mask = <0x8000000>; + /* LDOVBBMM_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBMM_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1200000 0 0x4 0 0x40000 0x1f00 /* FBB optional, vset */ + >; +}; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 658749b90b97..75b0c1669504 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -18,20 +18,20 @@ For twl6030 regulators/LDOs - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS -For twl6025 regulators/LDOs +For twl6032 regulators/LDOs - compatible: - - "ti,twl6025-ldo1" for LDO1 LDO - - "ti,twl6025-ldo2" for LDO2 LDO - - "ti,twl6025-ldo3" for LDO3 LDO - - "ti,twl6025-ldo4" for LDO4 LDO - - "ti,twl6025-ldo5" for LDO5 LDO - - "ti,twl6025-ldo6" for LDO6 LDO - - "ti,twl6025-ldo7" for LDO7 LDO - - "ti,twl6025-ldoln" for LDOLN LDO - - "ti,twl6025-ldousb" for LDOUSB LDO - - "ti,twl6025-smps3" for SMPS3 SMPS - - "ti,twl6025-smps4" for SMPS4 SMPS - - "ti,twl6025-vio" for VIO SMPS + - "ti,twl6032-ldo1" for LDO1 LDO + - "ti,twl6032-ldo2" for LDO2 LDO + - "ti,twl6032-ldo3" for LDO3 LDO + - "ti,twl6032-ldo4" for LDO4 LDO + - "ti,twl6032-ldo5" for LDO5 LDO + - "ti,twl6032-ldo6" for LDO6 LDO + - "ti,twl6032-ldo7" for LDO7 LDO + - "ti,twl6032-ldoln" for LDOLN LDO + - "ti,twl6032-ldousb" for LDOUSB LDO + - "ti,twl6032-smps3" for SMPS3 SMPS + - "ti,twl6032-smps4" for SMPS4 SMPS + - "ti,twl6032-vio" for VIO SMPS For twl4030 regulators/LDOs - compatible: - "ti,twl4030-vaux1" for VAUX1 LDO |